Használati útmutató Pyle PDA30BU

Pyle Vevő PDA30BU

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Pyle PDA30BU (6 oldal) a Vevő kategóriában. Ezt az útmutatót 2 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Oldal 1/6
Wireless Stereo Power Amplifier BT Compatible
PDA30BU
Blue Series Compact and Audio Streaming Amp
with RCA & Speaker Terminals
www.PyleUSA.com
2
Read through this user manual before using the product
to ensure its correct use. Keep this manual for future reference.
Quick Setup:
1. Main Power ON Switch: Switch ON/OFF the amplier by using this switch.
2. --LINE input model --Wireless BT input model.Input LED: RED Green
3. MIC Input
4. Mic volume control: Use this control to set the volume level of Microphone.
5. Adjust to boost or cut LOW frequencies.BASS KNOB:
6. Adjust to boost or cut HIGH frequencies.TREBLE KNOB:
7. Master Volume: Adjusts main audio system volume level.
8. Lets you connect the desired LINE input source.RCA L/R LINE Input:
9. Speaker output (L/R)
10. AC IN
11. Wireless BT Antenna: Wireless BT Streaming receiver
Rear PanelFront Panel
www.PyleUSA.com
3
Setup and pairing (Wireless BT ampliers) are really easy. The following
instructions will help you connect Audio Ampliers to your music system or
pair with your tablet, computer, or smartphone.
1. Connecting the Speaker Wire
Audio stereo power ampliers that will power one pair of passive speakers
between 4 and 8 ohms (or subwoofer if you got the 2.1 CH amp or subwoofer
amp). To connect the amplier to your speakers you will need 2-conductor
stranded speaker wire. The ampliers use high-quality binding posts that will
accept heavy gauge bare wire banana plugs, spade lugs, or pin terminators.
If you use your own speaker wire we recommend using at least 16 gauge wire
and using the same length of wire from the amplier to each speaker It's also a
good idea to turn o your amplier before connecting power, audio sources or
speakers.
Preparing the Speaker Wire
1. Separate the last 3" of each speaker wire conductor.
2. Strip 1/2" of insulation from the end of each wire.
3. Twist the exposed copper strands with your ngers 3 or 4 times so the strands
stay together.
NOTE:
As you make your connections, be sure to connect the positive (+) terminals on
your amplier to the positive (+) terminals on your speakers. Even if your wire does
not have (+) or (-) markings, most 2-conductor speaker wire has printing on one
side to help you dierentiate between the wire pairs.
If you are Using Bare Wire
1. Use your thumb and nger to unscrew the binding post connectors on the back
of each speaker.
2. Insert each speaker wire into the holes on the side of the binding post connectors,
observing proper polarity.
3. Retighten the binding posts with your ngers.
4. The stripped portion of the wire should be secured rmly in each connector.
5. Make sure that none of the speaker wire strands have come in contact with an
adjoining terminal.

Termékspecifikációk

Márka: Pyle
Kategória: Vevő
Modell: PDA30BU

Szüksége van segítségre?

Ha segítségre van szüksége Pyle PDA30BU, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek




Útmutatók Vevő Pyle

Pyle

Pyle PLMRMBT5B Útmutató

6 December 2024
Pyle

Pyle P3001AT Útmutató

6 December 2024
Pyle

Pyle PLA2200 Útmutató

30 Szeptember 2024
Pyle

Pyle PTAU45.5 Útmutató

22 Szeptember 2024
Pyle

Pyle PWMA3003BT Útmutató

21 Szeptember 2024
Pyle

Pyle PDC22 Útmutató

19 Szeptember 2024
Pyle

Pyle PFA320BT Útmutató

18 Szeptember 2024
Pyle

Pyle PTAUWIFI46 Útmutató

16 Szeptember 2024
Pyle

Pyle PPG-460A Útmutató

13 Szeptember 2024

Útmutatók Vevő

Legújabb útmutatók Vevő