Használati útmutató Power Dynamics PDA-B2500

Power Dynamics Vevő PDA-B2500

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Power Dynamics PDA-B2500 (6 oldal) a Vevő kategóriában. Ezt az útmutatót 8 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Oldal 1/6
171.193
171.193
171.193
171.193 171.193
171.
171.
171.
171.171.194
194
194
194 194
171.196
171.196
171.196
171.196 171.196
PDA-B1500
PDA-B1500
PDA-B1500
PDA-B1500 PDA-B1500
2x
2x
2x
2x 2x
75
75
75
75750W
0W
0W
0W0W
PDA-B2000
PDA-B2000
PDA-B2000
PDA-B2000 PDA-B2000
2x
2x
2x
2x 2x 0
0
0
00
10
10
10
1010 0W
0W
0W
0W0W
PDA-B2500
PDA-B2500
PDA-B2500
PDA-B2500 PDA-B2500
2x
2x
2x
2x 2x
1200W
1200W
1200W
1200W1200W
PDA-B SERIES
6 - 31
DISPLAY
Standard indication:
Line- Output power of both output channels. Amplier calculated the output power. 1:
NOTE : Select the correct load impedance (button 8)
Calculation not 100% correct in bridge operatio
Line- If CLIP ON the amplier input/output is overloaded. Reduce in that case the input level. 2:
Line- Protection information. 3:
Line- Tempeture of the output stage of both channels 4:
Bargraph: Vertical bargraph in the middle of LCD display indication the output signal level of both
channels
Indication for a few seconds after actuating a volume controller:
Line 1:- Operation mode STEREO, BRIDGE or PARALL
Line- Limiter ON or OFF 2:
Line-3 & 4: ATTEN, attenuation of the input signals, line 4 shows the level.
Bargraph: Vertical bargraph in the middle of LCD display indication the output signal level of both
channels
Indication for a few seconds after selection the output impedance button (8):
Selected the correct output load for the calculation of the output power.
19 31 -
DISPLAY
Standard Indikation:
Zeile- Hier wird die Ausgangsleistung angezeigt der beiden Kanäle, vom Verstärker berechnet. 1:
Hinweis : Selekti en Sie 4 oder 8 Ohm Impedanz (Frontseite taste 8) er
Zeile- Bei Überlastung eines Kanals lautet die Anzeige 2: “CLIP ON” . Drehen Sie die
Lautstärkeregler auf Minimum.
Zeile- Wenn die Anzeige lautet tritt den Überlastschutz in Kraft. 3: “PROT ON”
Zeile- Hier wird die Temperatur von beiden Kanälen angezeigt. 4:
Balkendiagramm: Das Niveau (vertikaler Strich) der Ausgang der beiden Kanäle wird in der Mitte des
LCD-Displays angezeigt.
Indikation (für ein paar Sekunden) wenn der Lautstärkeregler gedreht wird:
Zeile- STEREO o BRIDGE-Modus wird hier gezeigt. 1: der
Zeile- Limiter ist ON (Ein) oder OFF (Aus). 2:
Zeile-3 & 4: ATTEN = Eingangspegel der beide Kanäle wird hier gezeigt.
Balkendiagramm: Das Niveau (vertikaler Strich) der Ausgang der beiden Kanäle wird in der Mitte des
LCD-Displays angezeigt.
Für ein paar Sekunden wird der Ausgangsimpedanz gezeigt (mit Taste 8 gewählt):
Der Verstärker benötigt die Einstellung um die Ausgangsleistung zu berechnen.

Termékspecifikációk

Márka: Power Dynamics
Kategória: Vevő
Modell: PDA-B2500

Szüksége van segítségre?

Ha segítségre van szüksége Power Dynamics PDA-B2500, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek




Útmutatók Vevő Power Dynamics

Útmutatók Vevő

Legújabb útmutatók Vevő