Használati útmutató PCE Instruments PCE-CT 50

PCE Instruments Mérőberendezések PCE-CT 50

Olvassa el alább 📖 a magyar nyelvű használati útmutatót PCE Instruments PCE-CT 50 (3 oldal) a Mérőberendezések kategóriában. Ezt az útmutatót 3 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF

Oldal 1/3

Manual

Thickness Gauge

PCE-CT 40 / PCE-CT 50

PCE Americas Inc.

711 Commerce Way

Suite 8

Jupiter

FL-33458

USA

From outside US: +1

Tel: (561) 320-9162

Fax: (561) 320-9176

info@pce-americas.com

www.pce-instruments.com/english

www.pce-instruments.com

PCE Instruments UK Ltd.

Units 12/13

Southpoint Business Park

Ensign way

Hampshire / Southampton

United Kingdom, SO31 4RF

From outside UK: +44

Tel: (0) 2380 98703 0

Fax: (0) 2380 98703 9

info@pce-instruments.com

Congratulations on the purchase of our coating

thickness gauge PCE-CT 40 / 50

Description

The is a simple in use andPCE-CT 40 / 50

cost effective measuring device. It belongs to a

range of non-destructive coating thickness

gauges.

Measuring ability of PCE-CT 40 / 50

It is easy and handy to use and allows the user

to make all necessary adjustments with the aid

of a menu ( –button). This allows forMODE

change to be implemented quickly and simply.

The gauge can be used for aPCE-CT 40 / 50

wide variety of applications and has to offer a

large measuring range from 0 to 5 mm. Modern

electronic and the robust casing guarantee an

extended lifetime for the high precision

instruments.

Battery exchange

The gauge is powered by a PCE-CT 40 / 50

9V alkaline battery. The battery compartment

can be found in the top back portion of the

instrument. If a battery icon appears in the

display, the battery has to be exchanged.

If a replacement battery is not available

immediately, several measurements can still be

taken until the gauge shuts down completely

(the display shows bA

bAbAT

TT and a discontinuous

beep tone is audible).

Attention: Exhausted batteries are hazardous

waste. Used batteries not with the domestic

waste decontaminate, but deliver at stated

collective places.

Switching on and off of the device

➢The gauge can be switched on manually

via pressing of -button or by ON/OFF

directly placing the probe on the

measurement object.

➢It appears or Sd4

Sd4

Sd4Sd4 Sd5

Sd5

Sd5Sd5 (name of device) and

then the last measured value.

➢The gauge switched off automatically after

40 seconds of non-use or by long pressing

(about 3 seconds) of -button.ON/OFF

Handling and storage

The gauge is a high precisionPCE-CT 40 / 50

instrument with a wide scope of applications. It

is therefore of great importance that the device

is handled with care to ensure a long life and a

prerequisite for precise and accurate

measurement results. The following guidelines

are to be followed to achieve the above:

➢Protect the device from dust and dirt.

➢Do not drop the device to the floor.

➢Protect the device from moisture,

aggressive vapors and chemicals.

➢After use please put the device in the

carrying case.

➢Avoid direct strong sunlight and

temperature shocks as these can have a

negative influence on the measurement

result.

➢Precise measurement results can be

achieved only with a clean probe.

Therefore, use regularly a clean, damp

cloth.

➢Check the probe regularly for soiling such

as paint or iron particles.

➢If the device is not used for a long time, it is

advisable to remove the battery to avoid

possible damage caused by the leakage of

a battery.

➢If the device has a failure, contact your

supplier for help.

Taking measurements

➢Hold the device vertically on the location to

be measured.

➢Place the probe flat ( ).avoid tipping!

➢To get the best results, place the thumb on

the elliptical indicated position with the

other fingers behind the gauge for balance.

➢A beep is audible and the measured value

appears on the display.

➢Improper placement, as well as picking up

the device before the end of the

measurement and the zeroing on a non-

metallic surface (substrate) is displayed

with (error).

Er0

Er0Er0

➢If the coating thickness exceeds the

maximum range (5000 µm) or if the device

is placed on the incorrect substrate (wood,

paper, cardboard etc), the display shows InF

InF

InFInF

(infinite).

➢The V-groove on the measuring head helps

by measurements on round objects, such

as rods, tubes, shafts, radii etc.

Please do not perform measurements on

magnets and in magnetic fields.

Magnetic fields influence the results by the

PCE-CT 40 /Fe- and strong electromagnetic

radiation has the influence by the

PCE-CT 50 /NFe measurements.

Zero calibration

A zeroing of the instrument is necessary after

switching on, by different measurement

processes, inserting of new battery or after

prolonged use.

Place the device on the iron- or the aluminum

plate in the carrying case. You can also use a

piece of uncoated ferro (Fe) or non-ferro (NFe)

metal (substrate) used in your process. If the

displayed value is out of the basic tolerance,

the instrument has to be zeroed. The following

steps are to be taken to zero the gauge:

➢Remove the device from the zero plate or

the substrate.

➢Press the button. The display showsZero

P0.0

P0.0P0.0 (zero point).

➢Place the gauge on the zero plate or the

substrate. (infinity) appears followed by

PInPIn

a beep tone.

➢Lift the device at least 5 cm from the zero

plate. appears followed by another

0.0

0.00.0

beep.

➢To check the zeroing place the gauge on

the zero plate or the substrate again. 0.0

0.0

0.00.0

should appear on the display followed by

beep. If the result is different repeat the

zeroing procedure.

➢The device is now ready for accurate

measurements.

Note that it is not necessarily to receive the

same displayed result by repeated

measurements at the same location.

Measurement variations can be caused by

roughness, dirt or bumps.

The menu of PCE-CT 40 / 50

The various options from the menu can be

accessed by repeatedly pressing the -Mode

button. Pressing the -key allows to selectEnter

the displayed option. Now the -buttonMode

change or select the setting. Pressing of Enter

confirms your choice and exits the menu.

rST

rSTrST - Resetting the average value (mean)

of the measurements

( - Yes, - no)

YES

YESYES no

nono

CnT

CnTCnT - continuous measurement indicated

by icon in the displayCONT

( - On,

OnOn OFF

OFF

OFFOFF - Off)

UnT

UnTUnT - Choice of measuring unit between

microns / mm and mil

(25.4

25.4

25.425.4 - µm/mm, - mil)

11.00

0000

bEP

bEPbEP - Switching on or off of tons keys

( - On,

OnOn OFF

OFF

OFFOFF - Off)

SnSn - Displays the serial number of the

device

PCE-CT 40

all non-magnetic

coatings such as

synthetics,

lacquers, enamels,

copper, chromium,

zinc, etc.

on steel or

iron

PCE-CT 50

all isolating

coatings such as

lacquers,

synthetics,

enamels, paper,

glass, rubber etc.

on copper,

aluminum or brass.

This includes

anodized coatings

on aluminum as

well.

Display of the average value (mean) and the

number of measurements

The device calculates with each measurement

and without storing of individual results the

average value. The display of mean is due to

the short press (less than 3 seconds) of the

ON/OFF-button and is indicated with Ave

(average) icon in the display. If the -ON/OFF

button is short pressed again, the number of

last measurements applied to the mean

together with icon appears in the display. Then

rST

rSTrST option of the menu resets these values.

Delivery

➢Coating thickness gauge PCE-CT 40 / 50

➢Carrying case with zero plate (steel or aluminum )

➢9 Volt battery (alkaline)

➢user manual

Technical Specifications

Base material (substrate)

steel or iron:

Non magnetic metals:

such zinc, copper, brass,

aluminum, stainless steel,

anodized aluminum:

Continuous measuring range:

Display of measured values:

Display resolution:

Repeatability (basic tolerance):

Minimum object size:

Minimum curvature:

convex:

concave:

Minimum substrate thickness:

PCE-CT 40 /Fe:

PCE-CT 50 /NFe:

Temperature range:

Storing:

Operating:

Probes:

Power supply:

Dimension (LxWxH):

Weight incl. battery:

PCE-CT 40 /Fe

PCE-CT 50 /NFe

0 - 5000 µm or 0 -196 mil

from 0.0 - 999 in µm

from 1.00 - 3.50 in mm

or from 0.00 - 140 mil

0,1 µm in the range of 0.0 - 99.9 µm

1 µm in the range of 100 - 999 µm

0.01 mm in the range of 1.00 – 5.00 mm

0.01 mil in the range of 0.00 - 9.99 mil

0.1 mil in the range of 10.0 - 99.9 mil

1.0 mil in the range of 100 - 196 mil

+/- (1,5 µm + 2%) from 0 - 1000 µm

+/- 3,5% from 1.00 – 5.00 mm

10 x 10 mm² or (0.4“ x 0.4“)

5 mm or 0.02“

30 mm or 1“

0.20 mm or 8 mil

0.05 mm or 2 mil

-10°C to +60°C (14°F to 140°F)

0°C to +60°C (32°F to 140°F)

Single point

9 Volt E block alkaline

118 x 58 x 38 mm or 4.6" x 2.3" x 1.5"

approx. 150 g or 5.3 oz

DIN 50981, 50984

ISO 2178, 2360, 2808

BS 5411 (3, 11) 3900 (c, 5)

ASTM B499, D1400

Technical data subject to change without notification.

Stand: 05/2016

Termékspecifikációk

Márka:	PCE Instruments
Kategória:	Mérőberendezések
Modell:	PCE-CT 50

Szüksége van segítségre?

Ha segítségre van szüksége PCE Instruments PCE-CT 50, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek

Az Ön neve*

Az Ön e-mail címe*

Írja ide kérdését

Útmutatók Mérőberendezések PCE Instruments

PCE Instruments PCE-HT-225A Útmutató

29 Március 2025

PCE Instruments PCE-DD-A Útmutató

28 Március 2025

PCE Instruments PCE-128 Útmutató

28 Március 2025

PCE Instruments PCE-3000UL Útmutató

28 Március 2025

PCE Instruments PCE-BPD-C-66A Útmutató

28 Március 2025

PCE Instruments PCE-DFG N 5TW Útmutató

28 Március 2025

PCE Instruments PCE-MA 100 Útmutató

28 Március 2025

PCE Instruments PCE-MA 110 Útmutató

28 Március 2025

PCE Instruments PCE-DFG NF 5K Útmutató

28 Március 2025

PCE Instruments PCE-LES 103UV Útmutató

28 Március 2025

Útmutatók Mérőberendezések

Legújabb útmutatók Mérőberendezések

Uni-T UT220 Útmutató

3 Április 2025

Uni-T UT681C Útmutató

3 Április 2025

Uni-T UT216C Útmutató

3 Április 2025

Uni-T UT611 Útmutató

3 Április 2025

Uni-T UT210D Útmutató

3 Április 2025

Uni-T UT210C Útmutató

3 Április 2025

Uni-T UT210B Útmutató

3 Április 2025

Uni-T UT682 Útmutató

3 Április 2025

Uni-T UT275 Útmutató

3 Április 2025

Uni-T UT08A Útmutató

3 Április 2025