Használati útmutató Pantum P3502DN

Pantum nyomtató P3502DN

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Pantum P3502DN (100 oldal) a nyomtató kategóriában. Ezt az útmutatót 3 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF

Oldal 1/100

It is recommended to carefully read this Guide before using the printer

Pantum P3500 Series

Monochrome Single Function Laser Printer

User Guide

Preface

Welcome to the Pantum series products!

We heartily appreciate your using of Pantum series products!

To protect your vital interests, please carefully read the following statements.

Legal Notice

Trademark

Pantum and Pantum logos are registered trademarks of Zhuhai Pantum Electronics Co.,Ltd.

Microsoft®, Windows®, Windows Server® and Windows Vista® are trademarks registered by

Microsoft Corporation in the United States or other countries/regions.

Mopria®, the Mopria® Logo and the Mopria® Alliance logo are registered trademarks and

service marks of Mopria Alliance, Inc. in the United States and other countries. Unauthorized

use is strictly prohibited.

AirPrint and the AirPrint logo are trademarks of Apple Inc.

Wi-Fi®, Wi-Fi Alliance®,Wi-Fi Protected Access®(WPA),the Wi-Fi CERTIFIED logo, the Wi-Fi

logo and the Wi-Fi Protected Setup logo are registered trademarks of Wi-Fi Alliance.

The ownership to the names of the software in this User Guide belongs to their respective

companies in accordance with corresponding license agreement, and they are referred for

instructions only.

All other product and brand names herein may be the registered trademarks, trademarks or

service marks of their respective owners, and they are referred for instructions only.

The copyright of this User Guide is owned by Zhuhai Pantum Electronics Co.,Ltd.

It is prohibited to copy, translate, modify and transmit this User Guide by any means or in any

form without the prior written consent of Zhuhai Pantum Electronics Co.,Ltd.

Version: V1.2

Disclaimer

For a better user experience, Zhuhai Pantum Electronics Co.,Ltd. reserves the right to make

changes to the User Guide. The information contained herein is subject to change without

notice.

Users are responsible for any damages arising from failing to follow this User Guide.

Meanwhile, except the express warranty made in the product maintenance manual or service

commitment, Zhuhai Pantum Electronics Co.,Ltd. does not make any express or implied

warranty or guarantee to this User Guide (including composing or words).

Using this product to copy, print, scan certain documents or images or make other forms

of operations may be prohibited by the local laws. If you are uncertain about the legality of

using this product for certain documents or images, you should consult your legal advisor in

advance.

The product can only be used safely in the non-tropical areas at an altitude no higher than

2000 meters.

III

Safety Precautions

Laser Safety

The laser radiation is harmful to the human body. Since laser components are completely

sealed in the printer, laser radiation will not leak. To avoid laser radiation, please do not

randomly disassemble the printer!

The printer follows the provisions of Class 1 laser products under CFR standard. The printer

has a Class III b laser diode, which has no laser radiation leakage among laser components.

The laser components shall complies with the requirements of: U.S. Code of Federal

Regulations, 21 CFR 1040, IEC 60825-1

The following label is attached to the laser components inside the printer:

Reclamation and recycling

To protect the environment, our corporation has already established the system of reclamation

and recycling for waste products. Please refer to the Pantum ofcial website for product

recovery at www.pantum.com.

Safety Warning

Please note the following safety warnings before using the printer:

There is high-voltage electrode inside the printer. Before

cleaning the printer, make sure the power is turned off!

Plugging and unplugging the power cord plug with a

wet hand can result in an electric shock.

The fuser unit is attached with a high temperature

warning label. Please do not remove or damage

this label.

The fuser unit is hot when and after printing.

Touching the fuser unit (the shaded area as

shown) may cause burns!

Warning

Precautions

Precautions before Using the Printer:

1. Read and understand all instructions;

2. Familiarize yourself with the basic principles associated with operating electrical appliances;

3. Comply with all warnings and instructions marked on the equipment or specied in the manual

supplied with the equipment;

4. If the operating instructions conict with the safety information, please refer back to the safety

information, as you may have misunderstood the operating instructions. If you cannot resolve the

conicts, please call the Customer Service Hotline or contact a service representative for help;

5. Before cleaning the equipment, remove the power cord from the AC power supply outlet. Do not

use liquid or aerosol cleaners;

6. Please make sure that the equipment is put on a stable desktop surface to avoid serious damage

caused by the falling of the equipment;

7. Do not put the equipment near a radiator, an air conditioner, or a ventilation pipe;

8. Do not put any articles on the power cord. Do not put the equipment at the place where its power

cord could be stepped on by people;

9. Outlets and extension cords must not be overloaded. This may reduce performance and could

result in re or electric shock;

10. Do not allow pets to chew on the AC power cord or the computer interface cable;

11. Do not allow sharp objects piercing equipment slot, so as to avoid contact with the

high-voltage device, which otherwise may result in re or electric shock. Take care not to spill

liquids onto the equipment;

12. Do not disassemble the equipment so as to avoid the risk of electric shock. Necessary repairs may

only be carried out by professional maintenance personnel. Opening or removing the cover could

result in an electric shock or other potential hazards. Incorrect disassembly and assembly could

also result in an electric shock during future use;

13. If any one of the following occurs, disconnect the equipment from the computer and pull out the

power cord from the AC wall socket and contact a qualied member of the service personnel for

maintenance:

• Liquid has been spilled into the equipment.

• The equipment has been exposed to rain or water.

• The equipment falls, or the cover is damaged.

• Signicant changes in the equipment’s performance.

14. Only adjust the control mentioned in the instructions. Incorrect adjustment of other controls may result

in damage and mean that professional maintenance personnel need to spend more time xing it;

15. Do not use the equipment in a thunderstorm so as to avoid the risk of an electric shock. If possible,

pull out the AC power cord during a thunderstorm;

16. If you continuously print multiple pages, the surface of the tray will become very hot. Take care not

to touch this surface, and keep children away from this surface;

17. The signal wire of the device connected with the printer can not be connected to the outdoors;

18. Please ensure timely ventilation in case of a prolonged use or printing huge amounts of documents

in a poorly ventilated room;

19. In standby status, the product will automatically enter into the power saving (sleep) mode if it does

not receive any job order for a while (such as 1 minute); and it can realize zero power consumption

only if it has not been connected with any external input power supply;

20. As the Class 1 equipment, the product must be connected to the power supply outlet with

protective grounding line when using;

21.

This product should be placed according to the shipping marks on the product package box during delivery;

22. This product is a kind of low-voltage equipment. When using this product below the specied

voltage range, please refer to the product precautions or call Pantum Aftersales Service Centre, if

the toner comes off the printed contents, or the equipment starts slowly;

23. This product is sold as a complete machine. The consumers can go to Pantum Aftersales Service

Centre to purchase parts they need. If the product sold is inconsistent with the package list, please

go to the specied Aftersales Service Centre to solve the problem;

24. Install this product in a place with the temperature between 10°C and 32.5°C and the relative

humidity between 20% and 80%;

25. For security and other reasons the printer may switch to intermittent printing after a certain amount

of continuous printing.

26. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject

to the following two conditions:

(1) this device may not cause interference, and

(2) this device must accept any interference, including interference that may cause undesired

operation of the device.

27. IC Radiation Exposure Statement:

This equipment complies with Canada and FCC radiation exposure limits set forth for uncontrolled

environments. This equipment should be installed and operated with a minimum distance of 20cm

between the radiator and your body.

This transmitter must not be co-located or operating in conjunction with any other antenna or

transmitter.

28. This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can

be determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/TV technician for help.

29. Changes or modication not expressly approved by the party responsible for compliance could

void the user’s authority to operate the equipment.

30. The power consumption of the product is XXX W in networked standby if all wired network ports

are connected and all wireless network ports are activated;

31. Shielded cables must be used with this unit to ensure compliance with the Class B FCC limits.

32. The product's Power Consumption in Off mode is less than 0W, in Networked standby mode is less

than 0W.

33. Please keep this User Guide properly.

Legal Information

This symbol indicates that, at the end of your product’s life, it must not be discarded

as domestic waste. Instead, you should dispose of your used equipment at

a designated collection point for the recycling of waste electrical and electronic

equipment. Ref: EU Directive 2002/96/EC on Waste Electrical and Electronic

Equipment (WEEE). Please contact your distributor / supplier for further

information.

This product is suitable for indoor use only.

European Community (EC) directives conformity

This product complies with the protection requirements of EC directives 2004/108/

EC and 2006/95/EC on the approximation and harmonization of the laws of the

Member States relating to electromagnetic compatibility and safety of electrical

equipment designed for use within certain voltage limits.

The manufacturer of this product is: Zhuhai Pantum Electronics Co.,Ltd., No.3883,

Zhuhai Avenue, Zhuhai, Guangdong, China 519060.

A declaration of conformity to the requirements of the Directives is available upon

request from the Authorized Representative.

This product satises the Class B limits of EN 55022 and safety requirements of

EN 60950.

This printer is fully compliant with the ROHS Directive 2009/95/EC and the

requirements of the revised Directive 2011/65/EU for managing toxic and

hazardous substances.

VII

1. Before Using the Printer 1-2 .................................................................................................................

1.1. Packing List .............................................................................................................................1-2

1.2. Product View ............................................................................................................................1-3

1.3. Laser Toner Cartridge ..............................................................................................................1-5

1.4. Control Panel ...........................................................................................................................1-6

1.5. Print the Product Report ..........................................................................................................1-7

2. Paper and Print Media ....................................................................................................................2-2

2.1. Paper Specication ..................................................................................................................2-2

2.2. Loading Paper .........................................................................................................................2-4

2.2.1. Loading into Standard Input Tray .......................................................................................2-4

2.2.2. Loading into Multipurpose Input Tray .................................................................................2-6

2.2.3. Loading into Optional Tray .................................................................................................2-7

2.3. Non-printing Area .....................................................................................................................2-8

3. Installation and Uninstallation of the Driver Software .....................................................................3-2

3.1. Windows-based Driver .............................................................................................................3-2

3.1.1. Introduction ........................................................................................................................3-2

3.1.2. Installation Steps ................................................................................................................3-2

3.1.3. Driver Uninstallation .........................................................................................................3-11

3.2. Installation of the Driver Software based on Mac System .....................................................3-13

4. Network Conguration (For printer models that support wired/wireless network features) ............4-2

4.1. Wired Network Conguration (For printer models that support wired network features) .........4-2

4.2. Wireless Network Conguration (For printer models that support wireless network features) ...4-2

4.2.1. Wi-Fi Protected Setup ........................................................................................................4-2

4.2.2. Setting up through Wi-Fi Conguration Tool ......................................................................4-3

4.2.3. Setting up through Web Server ........................................................................................4-15

4.2.4. Turn on/off Wireless Device .............................................................................................4-16

4.3. Set Network Printer ................................................................................................................4-17

4.3.1. Web Server Settings ........................................................................................................4-17

4.3.2. Control Panel Settings ....................................................................................................4-20

5. Mobile Print....................................................................................................................................5-2

5.1. Infrastructure connection mode................................................................................................5-2

5.2. Wi-Fi hotspot connection mode (recommended)......................................................................5-3

5.2.1. Android device mobile printing............................................................................................5-3

5.2.2.IOS device mobile printing..................................................................................................5-4

6. System Settings..............................................................................................................................6-2

6.1. Language Setting .....................................................................................................................6-2

6.2. Sleep Time Setting ...................................................................................................................6-2

6.3. Toner Save Setting ..................................................................................................................6-3

6.4. Restore Factory Settings .........................................................................................................6-5

7. Print ................................................................................................................................................7-2

7.1. Print Function ...........................................................................................................................7-2

7.2. Tray Setup ...............................................................................................................................7-3

7.2.1. Tray Dial Settings ...............................................................................................................7-3

7.2.2. Tray Settings through Control Panel .................................................................................7-4

7.3. Open Help Document ..............................................................................................................7-5

7.4. Printing Mode ...........................................................................................................................7-5

7.4.1. Printing with Standard Input Tray .......................................................................................7-6

7.4.2. Printing with Multipurpose Input Tray .................................................................................7-6

7.4.3. Printing with Optional Tray .................................................................................................7-7

7.5. Automatic Duplex Print ............................................................................................................7-9

Table of Contents

VIII

8. Routine Maintenance......................................................................................................................8-2

8.1. Cleaning the Printer .................................................................................................................8-2

8.2. Maintenance of Laser Toner Cartridge ....................................................................................8-3

8.2.1. About Laser Toner Cartridge ..............................................................................................8-3

8.2.2. Replace Laser Toner Cartridge ..........................................................................................8-4

9. Troubleshooting ..............................................................................................................................9-2

9.1. Clearing Jammed Paper .........................................................................................................9-2

9.1.1. Paper Jam in the Tray ........................................................................................................9-2

9.1.2. Paper Jam in the Manual Input Tray .................................................................................9-3

9.1.3. Paper Jam in the Optional Tray .........................................................................................9-4

9.1.4. Internal Paper Jam .............................................................................................................9-5

9.1.5. Paper Jam in the Fuser Unit .............................................................................................9-6

9.1.6. Duplex Unit Jam .................................................................................................................9-7

9.2. Software Failure ......................................................................................................................9-8

9.3. Common Trouble Shooting .....................................................................................................9-8

9.3.1. Common Trouble ..............................................................................................................9-8

9.3.2. Image Defects .................................................................................................................9-10

1-1

Chapter

Before Using the Printer

1. Before Using the Printer 1-2 .................................................................................................................

1.1. Packing List .............................................................................................................................1-2

1.2. Product View ............................................................................................................................1-3

1.3. Laser Toner Cartridge ..............................................................................................................1-5

1.4. Control Panel ...........................................................................................................................1-6

1.5. Print the Product Report ..........................................................................................................1-7

1-2

1. Before Using the Printer

1.1. Packing List

When you open the package, make sure that the following parts are included in the carton:

Parts Name Quantity

Printer 1

Laser Toner Cartridge 1

USB Interface Cable 1

Power Cord 1

CD-ROM 1

Quick Setup Guide 1

Pantum Warranty 1

Note: • The Pantum Warranty may not be attached in some regions.

1-3

1.2. Product View

Side view

1 Output Bin For storing the printed paper

2 Control Panel To indicate the printer status and conduct the print settings

operation

3 Output Tray To prevent the printed paper from falling

4 Front Cover To open the front cover to take out the laser toner cartridge

5Multipurpose Input

Tray

To open the front cover of the multipurpose input tray, and

put in the print media

6Multipurpose Input

Tray Guide To adjust the width of the both sides of the paper

7 Main Power Switch To turn on or turn off the power supply

8 To hold the print paperStandard Input Tray

9 Paper-width Guide To adjust the width of the paper inside the standard input

tray

1-4

Rear view

1 USB Interface For directly connecting with the computer

2 Network Interface For connecting the printer to the network

3 Power Interface For connecting the power cord

4 Rear Cover To be opened for checking the jammed paper

5 Duplex Printing Unit For releasing jammed paper at the rear during duplex

printing

Note: • The illustration may vary with different models and features, please prevail in

kind.

1-5

1.3. Laser Toner Cartridge

Service Life of the Laser Toner Cartridge

Type Average Print Volume

Laser Toner Cartridge with

Standard Capacity

About 3,000 pages (The volume is based on ISO/IEC 19752

standard)

Laser Toner Cartridge with

High Capacity

About 6,000 pages (The volume is based on ISO/IEC 19752

standard)

Laser Toner Cartridge with

Ultra-high Capacity

About 10,000 pages (The volume is based on ISO/IEC 19752

standard)

Note: • The model is subject to volume increase without prior notice.

• Consumables capacity may vary depending on the different types used.

• We do not recommend using consumables other than that of the original

Pantum consumables.

• Any damages caused by using non-Pantum original consumables are not

covered by the Warranty.

• The appearances of laser toner cartridges will vary with different types,

illustrations are for reference only.

1-6

1.4. Control Panel

1. Layout and Functions of Control Panel

The layout of the printer control panel is shown below:

No. Name Functions

1 LCD Display The display provides information about the printer and can be

used for setting up the Product Settings.

2 UP

Press this button to browse through each menu and its

options.

For menu items need to input, change the numeric value by

cycle accumulating.

3 Menu Open the main menu of the control panel to conduct the menu

setting.

4 Down

Press this button to browse through each menu and its

options.

For menu items need to input, move the position of the cursor,

e.g., IP address input.

5Wi Fi/Conguration -

Report

This button can enable the Wi Fi feature and indicate the Wi Fi - -

connection status (only applicable to Wi Fi model).-

For non-Wi Fi model, this button will be used to print the -

"Printer Information Page" and the "Network Conguration

Report".

6 OK

• Press this button to save the settings.

• Open the submenu on the display of the control panel.

• Select the menu item.

7 Back

Back Arrow Button: use this button to perform the following

operations:

• Exit the control panel menu.

• Scroll back to the previous menu in the list in the submenu.

• Return to the previous menu; if already at the top menu,

return to the Ready interface.

8 Cancel Press this button to cancel the operation.

Cancel the current printing operation if there is any.

9 Status Indicator

This light indicates the ready, alarm and other statuses of the

printer.

Green light: Normal.

Orange light: Alarm or cartridge toner level is low.

Red light: Error.

10 Power Indicator Green for starting up, working, and sleeping; while staying on

indicates the power supply is ready

1-7

2. Status Indicator

The multi-colored LED indicator will display red, orange and green with the specic meanings

as follows:

Red indicates the emergence of a serious error, such as the laser toner cartridge

is not installed, the laser toner cartridge does not match the printer, or the paper

tray is out of paper; and in such a case, it will keep the red light on.

For specic error, see Chapter 9 Troubleshooting.

The display provides information about the printer and can be used for setting

up the Product Settings.

Press this button to browse through each menu and its options.

For menu items need to input, change the numeric value by cycle

accumulating.

1.5. Print the Product Report

Users can print the product report by manipulating the control panel. These pages can help

you understand the product information, diagnose and resolve product failures.

1) Press "Menu" to enter the Menu Settings interface.

2) Press direction key "▲" or "▼" to select the "5.Prt Info Rept" option.

3) Press "OK" to enter the Print Information Report interface, and users can print the product

report according to their needs.

Note: • In case of non-Wi-Fi model, users can also print the network conguration

report of the printer directly through the shortcut button of "Network Conguration

Report" on the control panel.

2-1

Chapter

Paper and Print Media

2. Paper and Print Media 2-2 ....................................................................................................................

2.1. Paper Specication ..................................................................................................................2-2

2.2. Loading Paper .........................................................................................................................2-4

2.2.1. Loading into Standard Input Tray .......................................................................................2-4

2.2.2. Loading into Multipurpose Input Tray .................................................................................2-6

2.2.3. Loading into Optional Tray .................................................................................................2-7

2.3. Non-printing Area .....................................................................................................................2-8

2-2

2. Paper and Print Media

2.1. Paper Specication

P3500

Series

Standard Input

Tray

Media type Plain, thin paper

Media size

Auto*, A4, A5 Short Edge, A5 Long Edge, A6, JIS

B5, IS0 B5, B6, Letter, Legal, Executive, Folio,

Ocio, Statement, 16K, Big 16K, 32K, Big 32K.

Media weight 60~105 g/m²

Maximum

capacity of the

tray

250 pages

Multipurpose

Feeder

Media type

Plain paper, thick paper, thin paper, transparent

lm paper, carton paper, label paper, envelope

paper

Media size

Auto*, A4, A5 Short Edge, A5 Long Edge, A6,

JIS B5, IS0 B5, B6, Letter, Legal, Executive,

Folio, Ocio, Statement, 16K, Big 16K, 32K, Big

32K, No.10 Env., Monarch Env, DL Env, C5 Env,

C6 Env, ZL, Japanese Postcard, Long Paper

(Maximum 1.2m), Custom, Yougata4, Postcard,

Younaga3, Nagaga3, Yougata2

Media weight 60~200 g/m²

Maximum

capacity of the

tray

60 pages

Optional Tray

Media type Auto*, Plain, thin paper

Media size

Auto*, A4, A5 Short Edge, JIS B5, IS0 B5, Letter,

Legal, Executive, Folio, Ocio, Statement, 16K,

Big 16K.

Media weight 60~105 g/m²

Maximum

capacity of the

tray

550 pages (single optional tray)

Output Tray

Capacity 150 pages

2-3

Note: • It is recommended to use the standard paper and recycled paper for the printer.

• It is not recommended to use special paper extensively, which may affect the

service life of the printer.

• The print media that does not meet the guidelines listed in this User Guide may

result in poor print quality, increased paper jam and excessive wear of the printer.

• Properties such as weight, composition, texture and humidity are important

factors affecting the printer performance and output quality.

• Please note the following matters when selecting the print media:

1. Desired print result: The selected print media should meet the requirement of

the print tasks.

2. Surface smoothness: The smoothness of the print media may affect the

sharpness of the print outcome.

3. Some print media may meet all the use guidelines contained herein, but

they still cannot bring satisfactory effect. This may be due to incorrect operation,

inappropriate temperature and humidity, or other factors beyond the control of

Pantum. Before purchasing large quantities of print media, make sure that the

print media meets the specications specied in this User Guide.

4. Using print media that does not meet these specifications may cause

damage to the printer.

Paper and Manuscript Use Principles

• Papers or manuscripts with rough texture, concave and convex, oil stain and good

smoothness have poor printing performance.

• Please make sure no dust and uff on the paper.

• Paper shall be put on a at surface and stored under a cool and dry environment.

Special Paper Description

This printer supports using special paper for printing. Special paper includes: label, envelope,

transparency, thick paper, thin paper, carton paper, etc. Special paper should be loaded into

the multipurpose input tray for printing.

Note: • When using special paper or print media, be sure to select the matched print

type and size in the print settings so as to get the best print result.

• A maximum of 60 pages can be loaded into the multipurpose input tray when

a special media is used for printing.

2-4

Please observe the following standards:

Types of Print

Media Correct Practices Incorrect Practices

Label

Use labels with no exposed lining

paper only.

Labels shall be put at when

using.

Use labels of full sheet only.

There is no guarantee that all the

labels in the market can meet

corresponding requirements.

Use wrinkled, blistering or damaged

labels.

Envelope Envelopes should be loaded

evenly.

Use wrinkled, nicked, stuck or damaged

envelopes.

Use envelopes with clips, snaps,

Windows, or coated linings.

Use envelopes with self-adhesive

stickers or other synthetic materials.

Transparency Use only transparencies approved

for use in laser printers.

Use transparent print media that is not

suitable for laser printers.

Thick paper,

carton paper

Use only heavy paper that

is approved for use in laser

printers and meets the weight

specications of this printer.

Use the paper whose weight is more

than the specication of the media

recommended for this printer, unless the

paper is approved for use in this printer.

2.2. Loading Paper

2.2.1. Loading into Standard Input Tray

1. Completely draw out the standard input tray from the printer.

2. Slide the paper-length guide and paper-width guide of the standard input tray to the desired

paper size slot, so as to match with the length and width of the paper.

Note: • Do not overly squeeze the "paper-length guide" and "paper-width guide",

otherwise it will easily lead to deformation of paper.

2-5

3. Unfold the stacked paper before loading to avoid paper jam or paper feed error, and then

load the paper into the tray with the print-side down; the standard input tray can be loaded

with 250 pages (80 g/m²) at maximum.

Note: • The printer tray is designed with the "paper type dial" for commonly used paper

size, which can be adjusted as required. When the paper type used for printing is

different from that the dial sets, the LCD display of the printer will show "PaprSize

Mismat." indicating an error, then it is necessary to reset the dial to eliminate the

error.

• For those paper types that are not shown on the dial, please set up the paper

size through the control panel.

4. Raise the output tray to avoid the printed paper from slipping and falling.

Note: • If the paper loaded into the standard tray at one time exceed 250 pages

(80 g/m²), paper will jam or cannot be fed in.

• If printing only the single side, please make the side to be printed (the blank

side) down.

2-6

2.2.2. Loading into Multipurpose Input Tray

1. Raise the output tray to avoid the printed paper from slipping and falling, or immediately

remove the printed document after the printing is completed.

2. Open the Multipurpose Input Tray

3. Slide the paper guides of the multipurpose input tray to match both sides of the paper. Do

not exert too much force, otherwise it will cause paper jam or paper skew.

4. Put the print media (such as an envelope or transparency) into the multipurpose input tray

with two hands until the front end of the envelope or transparency contacts the correction

roller.

Note: • When loading paper into the multipurpose input tray, and the paper source is

set up as Auto-select or Multipurpose Input Tray as specified, the printing will be

performed with the paper from the Multipurpose Input Tray as priority.

• 60 pieces of print media can be loaded into the multipurpose input tray each

time at maximum.

• Load the print media into the multipurpose input tray with the print-side up.

When loading, the top of the paper first enters into the multipurpose input tray.

• When using printed paper, please make the side to be printed (the blank side)

up.

• After printing, please immediately remove the paper, envelopes and

transparencies. Stacking paper or envelopes may cause a paper jam or the paper

curling.

2-7

2.2.3. Loading into Optional Tray

The optional trays can be overlaid for this printer, with each tray loaded with 550 pages

(80 g/m²) at maximum. If you need the optional trays, please contact the local distributor from

whom you bought the printer.

Note: • For installation of the optional tray, please refer to Chapter 7.

1. Completely draw out the optional input tray from the printer.

2. Slide the paper-length guide and paper-width guide of the tray to the desired paper size

slot, so as to match with the length and width of the paper.

Note: • Do not overly squeeze the "paper-length guide" and "paper-width guide",

otherwise it will easily lead to deformation of paper.

• To load the Legal size paper, press the release button on the rear of the tray to

draw out the rear, so as to lengthen the tray.

3. Unfold the stacked paper before loading to avoid paper jam or paper feed error, and then

load the paper into the tray with the print-side down; the optional input tray can be loaded with

550 pages (80 g/m²) at maximum.

2-8

Note: • The printer tray is designed with the "paper type dial" for commonly used paper

size, which can be adjusted as required. When the paper type used for printing is

different from that the dial sets, the LCD display of the printer will show "Optl tray

I, PaprSize Mismat." indicating an error, then it is necessary to reset the dial to

eliminate the error.

• For those paper types that are not shown on the dial, please set up the paper

size through the control panel.

4. Raise the output tray to avoid the printed paper from slipping and falling.

Note: • If the paper loaded into the optional tray at one time exceed 550 pages

(80 g/m²), paper will jam or cannot be fed in.

• If printing only the single side, please make the side to be printed (the blank

side) down.

• For installation of the optional tray, please refer to the Installation Guide

attached with the optional tray.

2.3. Non-printing Area

The shaded section indicates the non-printing area.

Usage Paper Size Top and Bottom

Margins (A)

Left and Right

Margins (B)

A4 5 mm (0.197 in) 5 mm (0.197 in)

Letter 5 mm (0.197 in) 5 mm (0.197 in)

Note: •The above margin settings only correspond to PCL6.

3-1

Chapter

Installation and

Uninstallation of the Driver

Software

3. Installation and Uninstallation of the Driver Software 3-2 .....................................................................

3.1. Windows-based Driver .............................................................................................................3-2

3.1.1. Introduction ........................................................................................................................3-2

3.1.2. Installation Steps ................................................................................................................3-2

3.1.3. Driver Uninstallation .........................................................................................................3-11

3.2. Installation of the Driver Software based on Mac System .....................................................3-13

3-2

3. Installation and Uninstallation of the Driver Software

3.1. Windows-based Driver

3.1.1. Introduction

Driver software helps users to run the installer and uninstaller through the installation and

uninstallation wizards, which provides the following modules and main functions:

• Autorun completes the automatic running of the installation CD.

• Installation: Provides users with the installation wizard of the printer driver.

• Uninstallation: Provides users with the uninstallation wizard of the printer driver.

Note: • For users of Windows XP and Windows Server 2003, when connecting the

equipment for the rst time, the system will pop up the window of Found New

Hardware Wizard. Please close this window. If this window is not closed, the

printer may not be detected, resulting in failure of installation.

3.1.2. Installation Steps

3.1.2.1 USB Model Installation.

1) Autorun Interface

After running the installation CD, the program will run automatically and display the following

interface:

3-3

2) Installation Interface

After the running of Autorun completes, the following installation interface appears:

Note: • The information shown on the interface may vary with different printer models.

Description of Options:

• it is the language corresponding to the operating system by default, Installation Language:

and users can select different languages according to their different needs.

• Select Printer: it shows the printer model, and users can select the corresponding model

based on the printer to be installed.

• the "USB printer" is checked by default.Installation Mode:

• click to view the User Guide documents.User Guide:

• "I agree to the License Agreement" is checked by default. Click the License Agreement:

agreement to open the corresponding window, as shown in the following gure:

3-4

Click "Back" to return to the original interface.

3) Installation Process Interface

Select Install to enter the Driver Installation Process interface.

3-5

4) Installation Complete

The program will automatically enter this interface after the driver installation is completed. It

will automatically exit in 3 seconds and set the printer as default.

3.1.2.2. NET Model (Wired and Wireless)

1) Running Interface

After inserting the CD, the main interface pops up and the program runs automatically.

3-6

2) Installation Conguration

After the running interface, it will enter the Installation Conguration interface. Users can

select the corresponding series name, language and installation method according to the

printer model to be installed.

Installation Instruction:

USB Printer: applicable to the local installation of all models.

Printers connected to the network: applicable to NET Model Network Installation; or

reinstallation when the Wi Fi Model has connected to the Internet.-

Printers connected to a new network: only applicable to the conguration of Wi Fi for -

models with Wi Fi function.-

1. Wired NET Model Installation

1) The following interface will display, if users install the Wired NET Model:

3-7

Users select the corresponding wired NET Model through "Select Printer", and the

corresponding installation options are available through Installation mode.

2) Search for Printers interface

After entering the Search for Printers interface, the program will automatically search for any

appropriate printer devices connected to the computer.

3-8

3) Printer List

After searching for printers, the program will automatically enter the "Select Printer" interface.

Users can select the found printer or add printer by manually adding IP or Host Name.

Note: • If the printer name does not appear in the Detected Printer, please click Refresh

and search for printers on the network;

• If you know the IP address of the printer to be connected, you can select Specify

an IP Address for Installation to enter the printer's IP address for connection.

4) Printer Installation Interface

Click on "Next" in the "Printer List" interface, the program will enter the "Printer Installation"

interface. After the installation is completed, it will enter the "Installation Complete" interface,

and exit in 3 seconds and set the printer as default.

3-9

2. Wi Fi Model Installation-

1) If users install the Wi Fi Model, the following interface will display:-

Users select the corresponding Wi Fi Model through "Select Printer", and the corresponding -

installation options are available through Installation mode. Generally, users select the third

installation method at the rst-time installation.

2) Wi Fi Conguration Interface-

3-10

Note: • At the rst installation, user can also install Wi Fi Model through Wi Fi - -

Conguration interface and connect the printer to Wi Fi. Please refer to -Chapter 4

for the specific setting steps of the Wi Fi configuration tools.-

3) Installation Complete Interface

This interface indicates that the installation is completed. It will automatically exit in 3 seconds

and set the printer as default.

3-11

3.1.3. Driver Uninstallation

1) Select Uninstallation Mode.

Click Start > All Programs to nd the "Pantum" folder, and then click the name of the product

to be uninstalled to enter the uninstallation interface. Or click Start > Control Panel, and then

click Uninstall Programs to nd the product to be uninstalled, with the uninstallation interface

shown as follows.

2) Select the name of the printer to be deleted, and click "Remove One" or directly click

"Remove All" to enter the uninstallation progress interface.

3-12

3) Uninstallation privilege verication prompt.

If any task remains in the print queue, a warning will pop up, saying "The Pantum P3500

Series Laser Printer is in use. Please uninstall the driver after the printing is completed." See

the gure below:

4) Complete Interface.

After the progress bar advancing is completed, it will enter the Complete Interface.

Click the "Done" button, the following window will pop up prompting you to restart the

computer. Click "OK" to exit the uninstaller and restart the computer; click "Cancel" to exit the

uninstaller.

3-13

3.2. Installation of the Driver Software based on Mac System

Introduction

The installation is divided into the following steps: introduction, license, destination volume,

installation type, installation, and summary.

Installation Steps:

1. Introduction

Insert the CD-ROM into the CD-ROM driver, run the CD-ROM and click the Mac system

installation package, then the following interface will display:

2. License

Click Continue on the above gure to display the contents of the License Agreement, as

shown below:

3-14

3. Click Continue, it will pop up the "To continue installing the software, you must agree to the

terms of the software license agreement." dialog box.

Click Agree to accept the License Agreement and continue the installation.

4. Installation Type

Display the installation-related information, as shown below.

Click Install, the following prompt box will pop up. Logging in as an administrator and getting

permission, you can continue with the installation.

3-15

5. Installation

The installation progress is shown below:

6. Summary

Installation completes, as shown below:

4-1

Chapter

Network Conguration

(For printer models that

support wired/wireless

network features)

4. Network Conguration (For printer models that support wired/wireless network features) ............4-2

4.1. Wired Network Conguration (For printer models that support wired network features) .........4-2

4.2. Wireless Network Conguration (For printer models that support wireless network features) ....4-2

4.2.1. Wi Fi Protected Setup- ........................................................................................................4-2

4.2.2. Setting up through Wi Fi Conguration Tool- ......................................................................4-3

4.2.3. Setting up through Web Server ........................................................................................4-15

4.2.4. Turn on/off Wireless Device .............................................................................................4-16

4.3. Set Network Printer ................................................................................................................4-17

4.3.1. Web Server Settings ........................................................................................................4-17

4.3.2. Control Panel Settings ....................................................................................................4-20

4-2

4. Network Configuration (For printer models that support

wired/wireless network features)

4.1. Wired Network Conguration (For printer models that support wired

network features)

Printers that support wired network printing can be connected to the LAN or WAN, thereby

the printer will work through a wired network connection.

In this setting, the printer is directly connected to the network and can be set to allow all

computers on the network to print directly on the printer, and achieve network sharing print.

Before starting the printer, rst connect the network cable to the network port of the printer

and ensure both the printer and the computer are under the same network environment to

directly connect the printer to the network. For detail installation steps, please refer to

Chapter 3.

4.2. Wireless Network Conguration (For printer models that support

wireless network features)

For printer models that support Wi Fi features, users can connect the printer with the wireless -

network through "Wi Fi Protected Setup", "Web Server Setup" or "Wi Fi Conguration Tool". - -

Wireless Workstation Mode

The printer communicates with the

wireless device via the access point.

Note: • The printer can connect with both the wired and wireless network at the same

time.

4.2.1. Wi Fi Protected Setup-

If the wireless router to which the printer is going to be connected supports the Wi Fi -

Protected Setup feature, it will be not necessary for users to use the computer, instead, they

can just use the "Wi Fi" button on the control panel of the printer to complete the connection -

between the printer and the wireless network.

Setup Method: Press and hold the "Wi Fi" button on the control panel of the printer for about -

2 seconds to start the , with the indicator of "Wi Fi" button beginning to ash. Wi-Fi Protected Setup -

Press the WPS button on the wireless router after 2 minutes of the launching, then the

printer will be connected to the wireless network.

4-3

Note: • The access point (or the wireless router) must support Wi Fi Protected Setup-.

4.2.2. Setting up through Wi Fi Conguration Tool-

Wi Fi conguration tool is a computer software that helps users to set the printer SSID, -

encryption method and password. Use USB cable to connect the printer with the computer,

then launch the Pantum wireless network conguration tool on your computer and conduct

wireless network conguration on the printer.

Open the Wi Fi conguration tool from the driver installation package. The specic steps are -

as follows:

4.2.2.1. Windows System

1) Detect Wireless Network Card

Wi Fi conguration tool can search the wireless network automatically by using a wireless card -

in the computer. If the computer does not have a wireless card, the option of "Enter SSID

Manually" will be automatically ticked on the "Wireless Network List" page. Please skip to

Step 3 in this case.

2) Wireless Network List

After launching the conguration tool, the display of Network List detected by the wireless

network conguration program appears, where you can select the wireless network.

4-4

Note:  •Afterlaunchingtheconfigurationtool,theNetworkListinterfaceappearswith

theinformationfoundbytheprogram,e.g.,thenameofthewirelessnetwork,

whichissortedbySSID.Userscanselectaniteminthelist,andthendouble-

clickorclickNexttoentertheInformationInputinterface.

•"EnterSSIDManually":clicktoswitchtotheEnterSSIDManuallyinterface,i.e.,

Step3.

•"Refresh":Searchingforwirelessnetworkinformationagain.

•"Next":EntertheInformationInputinterface.

•"Cancel":Thepromptofcancellationappearsafterclickingit.Asshownbelow

(click"OK"toexit,otherwisestayattheoriginalinterface).

3)EnterSSIDManually

Click"EnterSSIDManually"toswitchtotheinterfaceofmanuallyenteringtheSSID.

EntertheSSIDfortheprintertobeconnectedinthe"SSID"bar.

ClickPrintWirelessNetworkInformationPagetoprintthelistofwirelessnetworksdetected

bytheprinter.

4-5

Note: • If the printer with current conguration has ongoing printing work, the following

error prompting window will pop up.

4) Information Input Conguration

Entering the Information Input interface, users can set relative information of the wireless

network.

Note: • Safe Mode is currently available in three types: None, WEP, and WPA/WPA2.

When it is None, the password entry eld will be hidden, which means no

password is needed while connecting the SSID provided. The range for WEP

entry is 1-26 characters, and that of WPA/WPA2 is 8-64 characters.

• Show Password is unchecked by default; when it is checked, the password

entered will be displayed as it is instead of asterisks.

4-6

If the printer with current conguration has ongoing printing work, the following error

prompting window will pop up.

5) Conguration Completed

After completing the above steps, the Wireless Network Conguration Result interface pops

up. The conguration result will be displayed.

If the conguration of the printer’s wireless network is successful, the following interface will

pop up:

4-7

The following message will appear if the printer is not connected to the computer: Please use

the USB cable provided to connect your printer with the computer.

Click "Next" and the program will automatically search for the printers connected to the PC

currently. If searching for the printer models supported by this PC is failed, it will remain at

the current interface; if it nds any supported models, a message of "Trying to establish

a wireless connection with the printer" will pop up.

4-8

The following message will appear if the printer fails to apply the conguration by using the

wireless network provided:

The printer cannot connect to any wireless networks with the wireless credentials provided.

To reenter the credentials, please click Previous.

The following message will appear if the printer can apply the conguration by using the

wireless network provided, but the PC does not support the wireless network:

"The printer can successfully connect to a wireless network with the wireless credentials

provided. However, this computer is unable to communicate with the printer."

4-9

4.2.2.2. Mac System Conguration

The following operating systems are supported: Mac OS 10.6, 10.7, 10.8, 10.9, and 10.1 . 10.10 1

1) Detect Wireless Network Card

Wi Fi conguration tool can search the wireless network automatically by using a wireless card -

in the computer. If the computer does not have a wireless card, the option of "Enter SSID

Manually" will be automatically ticked on the "Wireless Network List" page. Please skip to

Step 3 in this case.

2) Wireless Network List

After launching the conguration tool, the display of Network List detected by the wireless

network conguration program appears, where you can select the wireless network.

4-10

Note: • After launching the conguration tool, the Network List interface appears with

the information found by the program, e.g., the name of the wireless network,

which is sorted by SSID. Users can select an item in the list, and then double-

click or click Next to enter the Information Input interface.

• Enter SSID Manually: click to switch to the Enter SSID Manually interface, i.e.,

Step 3.

• Refresh: Searching for wireless network information again.

• Next: Enter the Information Input interface.

• Cancel: The prompt of cancellation appears after clicking it. As shown below

(click OK to cancel, click Cancel to stay at the original interface):

3) Enter SSID Manually

Click "Enter SSID Manually" to switch to the interface of manually entering the SSID.

4-11

SSID: enter the service set identier of the network for the printer to be connected, with the

maximum length of 32 characters.

Print Wireless Network Information Page: allow you to print the list of wireless networks

detected by the printer.

Next: enter the Information Input interface.

Note: • If the printer with current conguration has ongoing printing work, the following

error prompting window will pop up.

4) Information Input Conguration

Entering the Information Input interface, users can set relative information of the wireless

network.

4-12

Note: • Safe Mode is currently available in three types: None, WEP, and WPA/WPA2.

When it is None, the password entry field will be hidden, which means no

password is needed while connecting the SSID provided. The range for WEP

entry is 1-26 characters, and that of WPA/WPA2 is 8-64 characters.

• Show Password is unchecked by default; when it is checked, the password

entered will be displayed as it is instead of asterisks.

If the printer with current conguration has ongoing printing work, the following error

prompting window will pop up.

5) Conguration Completed

After completing the above steps, the Wireless Network Conguration Result interface pops

up. The conguration result will be displayed.

If the conguration of the printer’s wireless network is successful, the following interface will

pop up:

4-13

The following message will appear if the printer is not connected to the computer: Please use

the USB cable provided to connect your printer with the computer.

Click "Next" and the program will automatically search for the printers connected to the PC

currently. If searching for the printer models supported by this PC is failed, it will remain at

the current interface; if it nds any supported models, a message of "Trying to establish

a wireless connection with the printer" will pop up.

4-14

The following message will appear if the printer fails to apply the conguration by using the

wireless network provided:

The printer cannot connect to any wireless networks with the wireless credentials provided.

To reenter the credentials, please click Previous.

The following message will appear if the printer can apply the conguration by using the

wireless network provided, but the PC does not support the wireless network:

The printer can successfully connect to a wireless network with the wireless credentials

provided. However, this computer is unable to communicate with the printer.

4-15

If the printer can apply the conguration with the wireless network provided, and the PC

supports the wireless network, the following message will appear:

The printer can successfully connect to a wireless network with the wireless credentials

provided.

4.2.3. Setting up through Web Server

You can use the embedded Web server of the printer to conduct the wireless network

conguration.

1. Print the network information page, and view the IP address of the printer.

2. Enter the IP address into the Web browser's address bar to access the embedded Web

server of the printer. Click "Settings", and the page is shown as follows:

4-16

3. Click "Wireless Network" to enter the Wireless Network Conguration interface.

4.2.4. Turn on/off Wireless Device

If you want to disconnect the printer with the wireless network, you can turn off the wireless

feature of the printer via the Menu button on the control panel.

1) Press "Menu" to enter the Menu Settings interface.

2) Press direction key "▲" or "▼" to select the " .Network Set" option and press "OK".3

3) Press direction key "▲" or "▼" to select the "2.Wireless Conf" option and press "OK".

4) Select the "1.Wireless NetW" option, and press "OK" to select the "1.Turn Off" option, and

then click "OK" to turn off the wireless network.

After the wireless network is turned off, the indicator of the Wi Fi button on the control panel -

goes out.

4-17

4.3. Set Network Printer

User can control the network settings through the embedded Web Server of the printer or the

Printer Control Panel.

4.3.1. Web Server Settings

4.3.1.1. View Web Server or Change Network Settings

You can use the embedded Web server to view or change IP settings.

1. Print the network information page, and view the IP address of the printer.

Note: • For printing product network information page, please refer to .Chapter 1

Enter the IP address into the Web browser's address bar to access the embedded Web

server of the printer. The page is shown as the following gure:

Note: • This printer supports the HTTP application protocol, and users can realize

secure encrypted access by typing: https://xxxx… in the Web explorer.

4-18

2. There are Network Settings and Printer Settings in the "Settings" column. For Network

Settings, users can complete the settings of the Networking Protocol, wireless network, Wi Fi -

hotspot, etc.; for Printer Setting, can complete the settings of Printing Preferences, e-mail and

other relative conguration information.

4.3.1.2. Set or Change Web Page Login Password

Users can realize the management and control of the printer through User Management

Settings.

Steps:

1. To open the embedded Web server, please log in rst. The login page is shown as follows:

4-19

Note: • The default username of the printer is "admin", and the initial password is

"000000".

2. Click the "User Management" tab to perform the corresponding operations.

3. Enter the new password in the Password box and Conrm Password box.

4. In the bottom of the window, click Changes to save the settings.

4.3.1.3. IP Address

The printer's IP address can be automatically set through the DHCP function and can also be

set manually.

Automatic Setting

The DHCP automatic setting function is enabled by default.

1. Connect the printer to the network through a network cable and complete the startup

preparation work.

2. The printer will automatically obtain the IP address assigned by the server. The IP address

obtained automatically can be used after a few minutes.

Note: • If DHCP cannot automatically obtain the IP address, the printer will automatically

use the default IP address: 169.254.1.1.

• Due to the features of DHCP, the IP address of the printer automatically

assigned by the network may vary if the printer has not been used for a long

time or the network access point changes, which could result in unsuccessful

connection to the printer. It is recommended that the IP address automatically

assigned by the network is bound to the Mac address of the printer while the

DHCP function is enabled.

4-20

Manual Setting

Enter the IP address in the Web browser's address bar to open the embedded Web server.

1. Click Settings in the navigation bar to open the Settings page;

2. Select Network Settings - IP 4 Settings;v

3. Set IP Address Assignment Mode (Manual), IP Address and Subnet Mask. Other items are

optional;

4. Click Apply to save the settings.

Note: • You can use the embedded Web server to change the IP Address Assignment

Mode into Automatic or Manual.

• To reset all the parameter settings of the printer, users can restore to the factory

settings, and please refer to Chapter 6 for the specic operations.

4.3.2. Control Panel Settings

Users can set up the wired network and wireless network through the Control Panel menu.

4.3.2.1. Network Settings

Users can set the network status through Network Settings.

1) Press "Menu" to enter the Menu Settings interface.

2) Press direction key "▲" or "▼" to select the " .Network Set" option and press "OK".3

3) Press direction key "▲" or "▼" to select the "1.Wired Cong" and press "OK"; Press

direction key "▲" or "▼" to select "1.IPv4" or "2.IPv6".

4-21

4) Press direction key "▲" or "▼" to select the "2.Wireless Conf" and press "OK"; Press

direction key "▲" or "▼" to select "1.Wireless NetW" or "2.WPS PIN mode".

4.3.2.2. Network Information

Users can check the network status through Network Information.

1) Press "Menu" to enter the Menu Settings interface.

2) Press direction key "▲" or "▼" to select the "4.Network Info" option and press "OK".

3) Press direction key "

▲

" or "▼" to select "1.Wired Info", "2.Wireless Info", or "3.WiFi Hots

Info".

4-22

4) Select the "1.Wired Info" option and press "OK"; Press direction key "▲" or "▼" to select

"1.IP Address", "2.Subnet mask", or "3.Gateway".

5) Select the "2.Wireless Info" option and press "OK"; Press direction key "▲" or "▼" to select

"1 .Connect state", "2.IP Address", "3.Subnet mask", "4.Gateway", "5.Channel", or "6.SSID".

6) Select the "3.WiFi Hots Info" option and press "OK"; Press direction key "▲" or "▼" to

select "1.Status", "2.Device name", "3.IP Address", "4.Password", "5.Channel", or "6.Conn

device #".

5-1

Chapter

Mobile Print

5. Mobile Print.....................................................................................................................................5-2

5.1. Infrastructure connection mode ...............................................................................................5-2

5.2. Wi-Fi hotspot connection mode (recommended) .....................................................................5-3

5.2.1. Android device mobile printing ...........................................................................................5-3

5.2.2. OS device mobile printingI .................................................................................................5-4

5-2

5. Mobile Print

The connection modes of wireless network are comprised of infrastructure connection and

Wi-Fi hotspot (recommended) connection.

The mode of infrastructure connection:

connect wireless device via router

1. The mobile device which connects

to the access point via wireless

network

2. Access point (wireless router)

3. Wireless network printer

Wi-Fi hotspot connection mode:

mobile device connects with printer

which has Wi-Fi feature

1. The mobile device which connects

to the access point via wireless

network

2. Wireless network printer

5.1. Infrastructure connection mode

You can connect the mobile device with wireless network printer by using access point

(wireless router) as a medium.

Important note: Prior to the installation of wireless network, you must know both the network

name (SSID) and password of your access point (wireless router). If you're not sure of that,

please consult your network administrator or the manufacturer of the access point (wireless

router).

1. Connect the printer with the access point (wireless router), please refer to Chapter 4.2. for

connection method.

2. Connect the mobile device with the access point (wireless router), please consult your

network administrator or the manufacturer of the mobile device for the connection method.

3. If you're using Android mobile device, then you can use the Mopria mobile printing. Please

refer to Chapter 5.2.1. for how to print.

If you're using OS mobile device, then you can use the AirPrint mobile printing. Please I

refer to Chapter 5.2.2. for how to print.

5-3

5.2. Wi-Fi hotspot connection mode (recommended)

Instead of the using of the access point (wireless router), you can connect mobile device with

the Wi-Fi hotspot of wireless network printer.

5.2.1. Android device mobile printing

Mopria mobile printing is supported.

5.2.1.1. Mopria mobile print

Mopria mobile printing is required to install Android print plug-in at Mopria Print Service mobile

device. You can print photo, email, web page and document.

5.2.1.1.1. The operating systems and applications which support Mopria mobile

printing

1. Mopria mobile printing is suitable for Android4.4 or higher version.

2. Mopria mobile printing is supported by applications, e.g. Microsoft Ofce

1.01(16.0.4201.1006) or higher version, Adobe Reader (V11.7.1) or higher version.

For more information about applications which support Mopria printing, please visit:

http://mopria.org/Developers/SpotlightAppsWall.aspx

5.2.1.1.2. How to download Mopria Print Service

1. Download and install Mopria Print Service plugin to the Android mobile device from Google

Play Store.

5.2.1.1.3. Preliminary preparations

1. A printer with wireless network feature.

2. Android mobile device.

5.2.1.1.4. How to use Mopria mobile printing

Before printing, please set the Mopria print service as "ON".

1. Tap the "settings" of the Home Screen on Android mobile device, and select "print".

2. Set the "Mopria print service" as "ON".

For using Mopria mobile printing feature, please turn off " Cloud Print " or set “HP Print

Service Plugin” as "OFF".

The printing steps may varied by applications, taking Adobe Reader as an example for

explanation.

1. Turn on the printer.

2. Connect the Android mobile device with wireless network of the printer (Please refer to

Chapter 4.2. for how to connect).

3. Start the application (such as Adobe Reader).

4. Select document, and tap the upper right corner .

5. Tap "print".

6. Please make sure the Pantum printer is selected.

5-4

If you selected other printer (or failed to select any printer), please tap the pull-down menu of

printer, and select your Pantum printer.

7. Set printing parameters, e.g. print pages.

8. Tap “Print”.

Note: •If print failed, check whether the Android mobile device is connected to the

printer's wireless hotspot (Wi-Fi).

• If the Android mobile device did not detect any printer, check whether the printer

is powered on and the printer is turned on.

5.2.2. OS device mobile printingI

Only the AirPrint -certied printers are applicable for using AirPrint feature. Please check out

whether AirPrint -certied symbol is printed on the carton of the printer.

5.2.2.1. The operating systems which support OS mobile printingI

Applicable for OS7.0 or higher version.I

5.2.2.2. Preliminary preparations

1. A printer with wireless network feature.

2. OS mobile device.I

5.2.2.3. How to use AirPrint mobile printing

The printing steps may varied by applications, taking PDF as an example for explanation.

1. Turn on the printer.

2. Connect the OS mobile device with wireless network of the printer (Please refer to Chapter I

4.2. for how to connect).

3. Start the application (such as PDF).

4. Select document, and tap .

5. Tap "print".

6. Please make sure the Pantum printer is selected.

If you selected other printer (or failed to select any printer), please tap the pull-down menu of

printer, and select your Pantum printer.

7. Set printing parameters, e.g. print pages.

8. Tap “Print”.

Note: • If print failed, check whether the OS mobile device is connected to the printer's I

wireless hotspot (Wi-Fi).

• If the OS mobile device did not detect any printer, check whether the printer is I

powered on and the printer is turned on.

6-1

Chapter

System Settings

6. System Settings..............................................................................................................................6-2

6.1. Language Setting .....................................................................................................................6-2

6.2. Sleep Time Setting ...................................................................................................................6-2

6.3. Toner Save Setting ..................................................................................................................6-3

6.4. Restore Factory Settings .........................................................................................................6-5

6-2

6. System Settings

This Chapter mainly introduces some general settings.

6.1. Language Setting

1) Press "Menu" to enter the Menu Settings interface.

2) Press "OK" to select the "1.System Setting" option.

3) Press "OK" to select the "1.Language Set" option, as shown below:

6.2. Sleep Time Setting

Set the Sleep Time Mode can lower the power consumption. "Sleep time Set" allows users to

select the idle time before the device enter into Sleep Mode.

1) Press "Menu" to enter the Menu Settings interface.

2) Press "OK" to select the "1.System Setting" option.

3) Press direction key "▲" or "▼" to select the "2.Sleep time Set" option and press "OK".

6-3

4) Press direction key "▲" or "▼" to select "1min", "5min", "15min", "30min", "60min", or

"8hrs".

Note: • Pressing any button or sending any print job will wake it up when the printer is

in Sleep mode.

6.3. Toner Save Setting

Users can select Toner Save Setting to lower the cost of printing. When the Toner Save mode

is "On", the output color of the print will be lighter. The Default Setting is "Off".

1) Press "Menu" to enter the Menu Settings interface.

2) Press "OK" to select the "1.System Setting" option.

3) Press direction key "▲" or "▼" to select the "3.Toner Save" option and press "OK".

6-4

4) Press direction key "▲" or "▼" to select the "1.Turn Off" option and press "OK". When

symbol "*" appears after "1.Close", it indicates that the toner save setting is off; or press

direction key "▲" or "▼" to select the "2.Open" option and press "OK". When symbol "*"

appears after selecting the "2.Open" option, it indicates that the toner save setting is on.

5) Press "Menu" to exit the menu interface, or select "Back" which is the last item of each

menu, and press "OK" to exit the menu interface step by step.

The Second Method:

Click "Printing Preferences" and then the "Layout" button on the top left to enter the following

interface, and then select the "Toner Save" mode, under which the output color of the print will

be lighter.

6-5

6.4. Restore Factory Settings

"Restore Factory Settings" is used to restore the default settings of the printer.

1) Press "Menu" to enter the Menu Settings interface.

2) Press "OK" to select the "1.System Setting" option.

3) Press direction key "▲" or "▼" to select the "4.Restore Set" option and press "OK".

7-1

Chapter

7. Print 7-2 ................................................................................................................................................