Használati útmutató Paasche TS-1AS

Paasche nincs kategorizálva TS-1AS

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Paasche TS-1AS (3 oldal) a nincs kategorizálva kategóriában. Ezt az útmutatót 3 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF

Oldal 1/3

TS Specications:

• Dual Action • Siphon Feed • Internal Mix • Head Size .66mm • PTFE Packing

Options for Talon:

• .38mm head (TT-2 tip, TN-2 Needle and TA-2 Aircap) - Great for jobs requiring ne detail

• .66mm Fan Aircap (TAF-3 Aircap, TN-3 Needle and TT-3 tip) Will give a 2-1/2 to 3 inch at pattern

Working Pressures:

• Operating pressures 15-55 PSI; Maximum pressure 85 PSI. Fan aircap needs 20 PSI or more.

• 20-30 PSI is best for detail spraying w/ properly thinned paint

• Use the higher pressures for thicker material where ne detail is not critical or thin the paint to allow lower pressures.

Equipment Set-up:

The Airbrush is held in the same manner as a pen, with the index nger comfortably over the nger button.

1. Attach air hose to air supply and to airbrush. If using a regulator set pressure between 15 -55 PSI.

Airbrush Operation:

1. Press down on Finger Button to release air and pull back on button to control quantity of color.

2. To spray a ne line without heavy ends, start moving the airbrush without release of color. Then start the color at the

beginning of line and stop the color at the end, but continue the motion of the airbrush after the color has stopped.

3. Practice this movement until you can spray a ne line or a broad pattern without heavy build up at the beginning

or end of your strokes.

4. Speed of movement controls density of color and fading e󰀨ects at beginning and end of strokes.

5. For detail, hold the airbrush very close to the surface push down for air and pull back very slowly on the Finger

Button to release a small amount of paint.

6. For background work and broad e󰀨ects, hold the airbrush away from the work surface and pull back on Finger Button

to release required amount of color.

REMOVING / REPLAClNG THE NEEDLE AND HANDLE :

1. Unscrew the handle and loosen the Locknut- #TAL-19 by turning counterclockwise. Depress the Trigger- #TAL-37

and hold in Down position while removing or inserting the needle. This assures the needle moves freely through the

trigger. Gently remove the needle, rotating if necessary, Do NOT force out!

2. Inspect the condition of the needle. If it is bent or misshapen in any way, replace it with a new needle. A bent needle

can damage or split the Tip- #TT causing bubbles or a rough spray pattern.

3. Hold trigger in DOWN position, insert the new needle into the Rocker Assembly- #TAL-18. Gently push needle

through, rotating if necessary, push gently forward until the needle stops in the front of the tip.

4. Release trigger and tighten Locknut by turning clockwise.

REPLACING THE FINGER LEVER ASSEMBLY :

1. Hold trigger so the round side of the stem is to the front and at side to the back of the airbrush.

2. Insert trigger straight DOWN through the opening in the top of the airbrush shell.

4. You want the bottom of the trigger to cover the round ball on top of the exposed plunger. Once the connection is

made you should have spring action when pushing down on the trigger. Proceed to replace Rocker Assembly and

balance of parts as above. When the needle is inserted it will prevent the removal of the trigger.

1. Remove handle, loosen Locknut- #TAL-19 and withdraw needle about one inch (1”).

2. Un-screw the Aircap- #TA and remove. The Tip- #TT can now be Unscrewed with Wrench #TAL-28.

until it is seated fully forward into tip.

3. Place a new tip into position and tighten with wrench. The tip must be wrench tight. Finally push the needle forward

ADJUSTING WORN PACKING WASHER:

1. If Packing Assembly- #TAL-8 becomes worn or loose it must be tightened or replaced.

2. Tighten packing nut with small screwdriver. To reach packing all internal parts must be removed.

3. Replace needle and make sure packing nut is not too tight. A slight resistance to movement is needed when needle

is passed through.

4. Completely re-assemble guts of airbrush.

INSTRUCTIONS AND PARTS LIST TS-8/06/2019

TS – Airbrush

Double Action - Internal Mix

Siphon Feed

INTRODUCTlON:

Paasche® model TS features hand crafted

construction using quality materials. The body

is machined brass, polished and chrome

plated. Needles are stainless steel & the needle

packing is PTFE. Preferred by professional and

hobbyist alike.

REPLACING THE TIP:

CLEANING THE AIRBRUSH:

1. Paint passes from the bottle connection forward so the trigger area back will most likely not need cleaning.

2. You can back ush the paint into your bottle by covering the aircap with your nger and then pressing down on the

trigger and pulling slightly back. This forces paint from back into the bottle. Never use open cup for back ushing.

3. In between color changes or before storing attach bottle with cleaner and spray into sink until it runs clear.

4. Remove needle and wipe clean then replace.

5. If paint has dried you can remove the tip and aircap for soaking or soak just the front of the airbrush in cleaner.

6. Use cleaner for the material you are spraying. Keep trigger area dry if soaking.

PERSONAL SETTINGS:

Spring Housing- #TAL-17 Used to increase or decrease spring tension for the trigger pull back. Thread into the shell

until the trigger stroke feels comfortable. Threading in until it stops can cause the trigger to jam.

TROUBLESHOOTING:

Bubbling in cup:

1. Aircap- #TA needs to be tightened

2. Tip- #TT needs to be tightened further

Skipping or Spitting:

1. Paint too thick -reduce with thinner

2. Tip not seated -tighten Tip- #TT with wrench

3. Tip split or damaged needle -replace tip or needle

4. Needle or tip dirty -clean and replace

5. Air pressure too low -increase pressure or thin paint further (need 20 or more PSI to spray most paints)

Airbrush Not Spraying:

1. Clogged tip -remove tip and clean

2. Needle not moving -tighten needle locknut

3. Low air pressure -increase pressure (need 20 or more PSI to spray most paint)

Sprays double line or heavy to one side:

1. Split tip or bent needle - replace

2. Dirty tip or needle - remove and clean

Jammed trigger or poor trigger motion:

1. Adjust Spring Housing - screw or unscrew the housing to lessen or increase tension on trigger motion

2. Paint leaking to trigger area - remove guts of airbrush and slightly tighten packing or replace if needed

3. Lubricate needle and trigger - apply Paasche Airbrush Lube (AL-2) to needle shaft and trigger slot area

NO. PART DESCRIPTION

1. XI-41 Needle Protection Cap

*2. TA-3 Aircap (.66mm)

*3. TT-3 Tip (.66mm)

4. MIL-12 “O” Ring

5. TS-30 Shell Assembly

6. TAL-8 Packing Assembly PTFE

7. TAL-37 Trigger

8. TAL-18 Rocker Assembly

9. MIL-11 Needle Spring

10. TAL-17 Spring Housing

11. TAL-19 Needle Lock Nut

12. TS-33 Handle

13. TAL-14 Valve Casing

14. TAL-32 Air Valve Assembly

15. TAL-26 “O” Ring

16. TAL-22 “O” Ring

*17. TN-3 Needle (.66mm)

18. TAL-28 Wrench

19. TAL-35 Allen Wrench

20. A-22 Spring

Optional Items:

TAF-3 Fan Aircap for .66mm Head-

(uses TT-3 & TN-3)(Optional)

TT-1 & TT-2 Tip (.25mm & .38mm)

TN-1 & TN-2 Needle (.25mm & .38mm)

TA-1 & TA-2 Aircap (.25mm & .38mm)

T-227-1, 2 or 3 Complete Head Assembly

(.25mm, .38mm & .66mm)

(A)

*Note: Etch lines on Items

2.,3. and 17. indicate size.

All should match when

installed on airbrush.

For Multi-Language Manuals Go To: www.paascheairbrush.com

DA400R AIR COMPRESSOR (1/6 H.P.)

1/6 H.P. Piston Compressor with Auto shuto󰀨. Compressor shuts o󰀨 when airbrush is not

in use. Operating pressure 30 - 50 PSI depending on airbrush being used, delivers up to

55 psi.. 110-120VAC, 1 Ph, 60 Hz, 42L/Min. (1.48CFM), 1720 rpm. With Regulator R-75

& Moisture Trap included. Shipping Weight: 13 lbs. 9 oz. (6.16 kgs)

D500 AIR COMPRESSOR (1/8 H.P.) (ETL Listed)

Economical and suitable for all airbrushes spraying properly thinned uids. It is capable

of delivering up to 35 P.S.I. operating pressure depending on airbrush being used. The

Paasche D500 is an oilless piston compressor. It operates on 110-120 Volt, 1 phase,

60Hz, and delivers .4 C.F.M. @ 20 P.S.I. Shipping Weight: 8 lbs. 3 oz. (3.7kg)

D500SR AIR COMPRESSOR (1/8 H.P.), ETL Listed with Switch & R-75 Regulator

Economical and suitable for all airbrushes spraying properly thinned uids. Maximum 20

- 35 P.S.I. operating pressure depending on airbrush being used. The Paasche D500SR

is an oilless piston unit and comes with the Regulator/Filter with gauge. It operates R-75

on 110-120 Volt, 1 phase, 60Hz, and delivers .4 C.F.M. @ 20 Regulator will P.S.I. R75

regulate up to 35 P.S.I. depending on usage (intermittent or constant) and size of airbrush

being used. Shipping Weight: 8 lbs. 12 oz. (3.97kg)

D220R AIR COMPRESSOR (1/6 H.P.), with Switch & R-75 Regulator

Economical and suitable for all airbrushes spraying properly thinned uids. It is capable

of delivering 30 - 45 P.S.I. operating pressure depending on airbrush being used. The

Paasche D220R is an oilless diaphragm unit and comes with the R-75 Regulator/Filter

with gauge. It operates on 110-120 Volt, 1 phase, 60Hz, and delivers .7 C.F.M. @ 20

P.S.I. R75 Regulator will regulate up to 45 P.S.I. depending on usage (intermittent or

constant) and size of airbrush being used. Shipping Weight: 11 lbs. (5kg)

Printed in the USA

TS TALON CUP AND BOTTLE ASSEMBLIES

VL-1/4-OZ

(1/4oz Metal)

VL-3-OZ

(3oz Glass)

VL-1-OZ

(1oz Glass)

VLP-3-OZ

(3oz Plastic)

VL-2-OZ

(2oz Metal)

VLP-8-OZ

(8oz Plastic)

BA-60-3P

(3oz Plastic)

BA-60-1P

(1oz Plastic)

BA-60-4P

(3oz Plastic)

BA-60-2P

(1oz Plastic)

e BA bottle assemblies are a new cover conguration and all

use plastic bottle. e 2P and 4P are narrow neck and work with

most airbrush paint bottles like Createx and Paasche

WARNING: Spray materials may be harmful if

inhaled or allowed to come into contact with the

skin or eyes. Consult the product label and material

safety data sheet supplied for the spray material.

Follow all safety precautions. Well CAUTION:

Ventilated Area Required to remove fumes, dust or

overspray. Maximum Air Pressure 75 P.S.I.

For Multi-Language Manuals Go To: www.paascheairbrush.com

Paasche Airbrush Co. 9511 58th Place Kenosha, WI. 53144 Phone:773/867-9191 Email:info@paascheairbrush.com

Termékspecifikációk

Márka:	Paasche
Kategória:	nincs kategorizálva
Modell:	TS-1AS

Szüksége van segítségre?

Ha segítségre van szüksége Paasche TS-1AS, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek

Az Ön neve*

Az Ön e-mail címe*

Írja ide kérdését

Útmutatók nincs kategorizálva Paasche

Paasche 2000SI Útmutató

20 Augusztus 2024

Paasche VL-1AS Útmutató

20 Augusztus 2024

Paasche TS-3AS Útmutató

20 Augusztus 2024

Paasche D220R Útmutató

20 Augusztus 2024

Paasche VL-100D Útmutató

20 Augusztus 2024

Paasche RG-3AS Útmutató

20 Augusztus 2024

Paasche TG-1AS Útmutató

20 Augusztus 2024

Paasche H-100D Útmutató

20 Augusztus 2024

Paasche FP-1/32 Útmutató

20 Augusztus 2024

Paasche H-3AS Útmutató

20 Augusztus 2024

Útmutatók nincs kategorizálva

Legújabb útmutatók nincs kategorizálva

Roland SD-20 Útmutató

16 Október 2024

SilverCrest SRG 1300 C3 Útmutató

16 Október 2024

IFM TY0058 Útmutató

16 Október 2024

Thule Kit 186039 Útmutató

16 Október 2024

Blumfeldt Solidflor Útmutató

16 Október 2024

Dimplex QRAD200E Útmutató

16 Október 2024

DAS Audio AX-112-5 Útmutató

16 Október 2024

Ferplast Ergocomfort Freetime Útmutató

16 Október 2024

AEG MECK52 Útmutató

16 Október 2024

Black Diamond BD1121530000ALL1 Útmutató

16 Október 2024