Használati útmutató Ozito SCMS-8STANDU

Ozito Fűrészgép SCMS-8STANDU

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Ozito SCMS-8STANDU (2 oldal) a Fűrészgép kategóriában. Ezt az útmutatót 4 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/2
ASSEMBLY OF STAND
SLIDING
COMPOUND MITRE
SAW & STAND
210mm (8¼”)
ORIGINAL INSTRUCTIONS
STAND ASSEMBLY
STAND
FASTENERS
The stand is constructed by assembling each half of the structure and
then joining them together.
7 Bolt Small - 36 pc
8 Washer Small - 36 pc
9 Nut Small - 36 pc
10 Rubber Foot - 4 pc
11 Bolt Large with Rubber
Stopper - 4 pc
12 Saw Mounting Bolts - 4 pc
1 Short Upper Support - 2 pc
2 Short Lower Support - 2 pc
3 Long Upper Support - 2 pc
4 Long Lower Support - 2 pc
5 Upper Leg - 4 pc
6 Lower Leg - 4 pc
1197 10
16
2 3 4 5
x2
x2
x2
x2
x2
x2
x2
x2
x2
x2
x2
x2
x4 x4
1 Remove the stand components
from the box and group matching
pieces together. Check that you
have all the contents listed to the
left.
Note: All upper members can be
identied by the 2 holes very close
together.
2 Lay two upper and lower legs on
the ground aligning 2 of the bolt
holes, parallel to each other.
The upper leg sits outside the
lower leg.
3 Place one long lower support
in between the legs and align
the bolt holes. The side support
should have its lip on the high side
(facing up) and should sit inside
the legs.
Ensure the lip with the lengthened
bolt holes is facing upwards.
4 Once aligned, insert small bolts
into the 2 aligned holes at both
sides of the lower support. Insert
the bolt from the outside and
screw a small washer and nut
onto each bolt to secure (only
hand tight at this initial stage).
5 Place one long upper support on
the of the legs at the top outside
(This will ensure the mounting
holes will align correctly once
assembled)
Insert a bolt from the outside into
the 2 aligned holes at either side
of the upper support and hand
tighten a small washer and nut
onto each.
6 At this stage your frame should
look like this.
128
SCMS-8STANDU
Art.-No.: 30.003.16 I.-No.: 11017
WARNING! ONLY USE THIS STAND WITH THE PROVIDED
MITRE SAW. THE STAND MUST NOT BE USED WITH
OTHER PRODUCTS OR FOR OTHER APPLICATIONS.
SCMS-8STANDU
x2
x2
x2
12 Once all of the members are
joined together and all fasteners
are assembled, place the 4
mounting bolts into the holes
at the top of the stand. This
will ensure the mounting holes
align correctly while the stand is
tightened.
Tighten all nuts and bolts rmly.
Note: We recommend that the stand
is mounted to a stable surface
for additional stability.
13 The Rubber Feet can now be
tted and the large bolts with
rubber stops inserted into the
rubber feet.
These bolts can be adjusted to
level the stand.
14 Remove the mounting bolts that
you inserted prior to tightening
the stand, then place the saw on
the stand. The supplied mounting
bolts, washers and nuts should
be used to secure the saw to the
top of the stand.
7 Align one short lower support
inside the legs at the same height
as the long lower support. Ensure
that the lip of the side support is
facing up.
Insert 2 small bolts in the aligned
holes from the outside and
attaching a small washer and
nut (only hand tight at this initial
stage).
8 On the same side as Step 7,
assemble one short upper support
to the top of the upper leg using 2
small bolts, washers and nuts.
One half of the frame is now
complete.
9 Repeat the same process for the
other side, which should leave
you with 2 identical halves.
11 Align the holes of each opposing
member. Bolts, washers and nuts
can be inserted & tightened with
hand force only.
12 Insert a bolt into the 4 overlapping
lower support holes and attach a
washer and nut onto each.
10 These halves can now be aligned
together to complete the frame.
Note: Nuts & bolts should only be
nger tight at this stage.
0318

Termékspecifikációk

Márka: Ozito
Kategória: Fűrészgép
Modell: SCMS-8STANDU

Szüksége van segítségre?

Ha segítségre van szüksége Ozito SCMS-8STANDU, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók Fűrészgép Ozito

Ozito

Ozito PXBCS-1830 Útmutató

24 December 2024
Ozito

Ozito ECS-406A Útmutató

6 Október 2024
Ozito

Ozito OCS-018 Útmutató

21 Szeptember 2024
Ozito

Ozito PXCCSK-4182 Útmutató

4 Szeptember 2024
Ozito

Ozito PXBPCK-1825 Útmutató

4 Szeptember 2024
Ozito

Ozito PXTCSK-2520 Útmutató

4 Szeptember 2024
Ozito

Ozito PXPRSS-018 Útmutató

3 Szeptember 2024
Ozito

Ozito PXBPCS-1815 Útmutató

3 Szeptember 2024
Ozito

Ozito RTB-003 Útmutató

20 Augusztus 2024
Ozito

Ozito JSW-6100U Útmutató

19 Augusztus 2024

Útmutatók Fűrészgép

Legújabb útmutatók Fűrészgép

Bavaria By Einhell

Bavaria By Einhell BHS 66 Útmutató

3 Április 2025
Bavaria By Einhell

Bavaria By Einhell BPS 600 E Útmutató

3 Április 2025
Makita

Makita DCS4610 Útmutató

2 Április 2025
Makita

Makita DPC6430 Útmutató

1 Április 2025
Makita

Makita DCS431 Útmutató

1 Április 2025
Makita

Makita DCS430 Útmutató

1 Április 2025
Makita

Makita EK6101 Útmutató

1 Április 2025
Makita

Makita DCS6401 Útmutató

1 Április 2025
Kraftronic

Kraftronic KT-ST 550 Útmutató

30 Március 2025
Kraftronic

Kraftronic KT-US 650 Útmutató

30 Március 2025