Használati útmutató Onkyo SKF-201

Onkyo hangszóró SKF-201

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Onkyo SKF-201 (2 oldal) a hangszóró kategóriában. Ezt az útmutatót 3 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF

Oldal 1/2

Thank you for your purchase of the Onkyo speaker system.

Please read this manual thoroughly before using it.

Following the instructions in this manual will enable you to

obtain optimum performance and listening enjoyment from

your new speaker system.

Please retain this manual for future reference.

Before using this unit

The speaker cabinet is made of wood and is therefore

sensitive to extreme temperatures and humidity. Avoid

placing the speaker systems in locations subjected to direct

sunlight, or in smokey or in humid places, such as near an

air conditioner, humidiﬁer, bathroom, or kitchen. Doing so

may result in damage to the speaker.

Place the unit on a rigid, level surface. Placing it on a

slanted surface or weak base not only may cause the unit to

fall, but also results in decreased sound quality.

Be sure to turn oﬀ your ampliﬁer before connecting the

speaker system. Connecting them with the ampliﬁer's power

on may result in damage to the ampliﬁer or the speaker

system.

Keep water or other liquids away from the unit. If water is

spilled into the unit, not only the unit but also the speakers

themselves may be damaged.

Name and function of each part

Precaution on use

This speaker system can handle the speciﬁed input power

when it is used for ordinary music reproduction. If the

following abnormal signals are fed to the speaker, however,

an overcurrent may ﬂow in the internal circuits, causing

burning or breakage of the wires even if the input power is

below the speciﬁed rating.

1. Noise produced when FM station is not tuned in

2. Sound produced when fast-forwarding cassette tape

deck

3. High-frequency sound generated by an oscillator, an

electronic musical instruments, etc.

4. Oscillating ampliﬁer signals

5. Special test signals produced by audio checking CD, etc.

6. Sound produced when connecting or disconnecting audio

connection cables (Always turn off the amplifier’s power

before connecting or disconnecting cables.)

7. Howling when a microphone is used

Do not place magnetic objects such as screwdrivers and iron

parts near the speaker system since they use speakers with

strong magnets. Otherwise, the objects may be attracted,

causing injury or damaging the diaphragm.

Connection

Turn the sound volume to the minimum and turn OFF the

amplifier power switch (POWER) before connecting the speaker

cables.

The nominal impedance of this speaker system is 6

Ω

. Use only

amplifiers capable of handling this impedance.

Use the supplied speaker cables to connect between speaker 's

binding posts and the amplifier's speaker terminals as illustrated

below.

Connect the speaker cables securely to the terminals, with the

core wires twisted properly. In this case, make sure that the core

wires do not touch each other. Note that a short circuit in core

wires may result in damage to the amplifier.

✩This speaker system uses banana-plug compatible binding

posts.

Connect the Right and Left speakers (as viewed from the

listening position) to the amplifier's corresponding Right and Left

speaker terminals.

SKF-201

Front Speaker System

Before turning on the amplifier's power switch:

Make sure that the positive (+) and negative (–) speaker

cables do not contact each other. Otherwise, a short-circuit

may occur, causing damage to the ampliﬁer.

Be sure to connect the speaker cables with correct polarity

(connect the speaker's positive (+) and negative (–) binding

posts with the ampliﬁer's corresponding speaker terminals).

Reversed polarity results in impaired bass-range

reproduction, causing mislocalization of the sound image.

Also, be sure to connect the Right and Left speakers with

the ampliﬁer's corresponding speaker terminals.

Pull lightly on the speaker cables to ensure that they are

connected ﬁrmly.

R L

Ordinary connection (single-wiring)

1. Loosen the LOW-FREQUENCY binding post screws, with the

jumper bars attached.

2. Insert the speaker wires to the connection holes. Fasten the

screws securely again.

* To use banana-plug speaker cables, insert the banana plug

into the center hole of each binding post.

Note:

Make sure that the HIGH-FREQUENCY jumper bars are not loosened.

Bi-wiring connection (Remove the attached jumper bars.)

1. Using two sets of speaker cables, connect the HIGH FRE-

QUENCY and LOW-FREQUENCY binding posts independently

to your ampliﬁer.

2. On the ampliﬁer, connect the speaker cables to the speaker

output terminals paying close attention to maintain consistent

polarity (See below.).

Remove the

jumper bars.

Ampliﬁer's speaker output

terminals

(Or AV ampliﬁer's front

speaker output terminals)

Amplifier's speaker output terminals

(Or AV amplifier's front speaker output

terminals)

Cabinet

Grille

Grille plug holes

Woofer

Tweeter

Bass-reﬂex port

LOW-FREQUENCY binding post

HIGH-FREQUENCY binding post

ReplacementRemoval

Use with a TV set

In general, Braun tubes used for color television sets, etc. are

extremely sensitive and can be affected even by the magnetism of

the earth. If a speaker system is used near them, therefore, discol-

oration or distortion of pictures will occur. To allow use with color

television sets, etc., this speaker system is provided with magnetic

shielding.

Even so, discoloration may still result, depending on the installation

environment. If discoloration occurs, turn off the power of the

television set, wait for 15 to 30 minutes and then turn it on again.

This activates the self-demagnetizing function of the television set,

improving the display condition. If discoloration persists even after

performing this remedy, move the speaker apart from the television

set. Discoloration may also be caused when a magnet or other

magnetizing object exists near the television because of the

combined effect.

The sound quality a speaker system reproduces varies greatly

depending on the construction and area of the room where it is

installed, as well as the location and size of the furniture. For better-

quality sound, observe the following precautions.

Avoid placing the speaker system on an elevated object such as

on concrete blocks. Instead, place it on a rigid floor surface with

minimal vibration. Also note that high-quality bass cannot be

obtained if the speaker system is unstably positioned. Generally

speaking, placing the speaker system on several small-diameter

supports results in better bass than placing it directly on the

installation surface. Moreover, if you feel the bass reproduced by

the system is too weak, move the speaker system closer to the

wall behind it. You can thus control the strength of the repro-

duced bass by the position of the speakers.

In many rooms, the furniture and wall affect the reproduced

sound quality. For stereo sound reproduction, placing the Right

and Left speakers in the same condition produces the best

results. If they are placed in extremely different conditions, the

Right- and Left-channel balance will be adversely affected.

The ideal placement of the speaker system is as follows:

Imagine an equilateral triangle and position the Right and Left

speakers on both ends of the base. The ideal listening position is

at or slightly to the rear of the triangle apex.

Glazed doors or surrounding walls in front of the speaker system

may cause the resonance of specific frequency ranges due to

reflected sound. To eliminate this resonance, place some sound-

absorbing material such as a thick curtain in front of the doors or

walls.

Placement

Attaching and detaching the speaker grilles

This speaker system uses detachable grilles. Use the following

method to attach or detach the grilles.

1.While holding the bottom edge of the speaker grille with your

both hands, pull it gently toward you to remove the bottom of

the grille.

2.In the same way, gently pull the upper edge of the speaker

grille toward you to remove it from the main unit.

3.To replace the grill, push the projections at the corners into

the grille plug holes on the speaker cabinet.

Speaker care

Your Onkyo speakers are finished with a very high quality

polymer laminate covering that serves to protect the wood

speaker cabinet.

Wipe the cabinet periodically with a dry, silicon-embedded or

plain soft cloth.

The covering may be cleaned with a soft cloth moistened with

water and a mild soap. Avoid the use of furniture polishes or

harsh cleansers.

Use a soft brush or hand vacuum cleaner to remove dust and

lint from the grille material.

Speciﬁcations

Model SKF-201

Type 2-way bass reﬂex

Impedance 6 Ω

Maximum input power 150 W

Output sound pressure level 86 dB/W/m

Frequency response 30 Hz-35 kHz

Crossover frequency 1500 Hz

Cabinet capacity 55 L

Speaker Woofer: 20-cm cone x 2

Tweeter: 2.5-cm dome

Dimensions 264 (W) x 981 (H) x 345 (D) mm

(Overall dimensions)

Weight 20 kg

Accessory 2.5-m speaker cable (1)

Instruction manual (1)

Others Magnetic shielding

Termékspecifikációk

Márka:	Onkyo
Kategória:	hangszóró
Modell:	SKF-201

Szüksége van segítségre?

Ha segítségre van szüksége Onkyo SKF-201, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek

Az Ön neve*

Az Ön e-mail címe*

Írja ide kérdését

Útmutatók hangszóró Onkyo

Onkyo D-407M Útmutató

16 Szeptember 2024

Onkyo HTP-L50 Útmutató

30 Augusztus 2024

Onkyo HT-S3405 Útmutató

14 Augusztus 2024

Onkyo HTP-2S Útmutató

7 Augusztus 2024

Onkyo D-407F Útmutató

2 Augusztus 2024

Onkyo D-309H Útmutató

1 Augusztus 2024

Onkyo SKS-HT230 Útmutató

29 Július 2024

Onkyo SKR-L500 Útmutató

28 Július 2024

Onkyo SKS-101 Útmutató

27 Július 2024

Onkyo Smart Speaker G3 VC-GX30 Útmutató

26 Július 2024

Útmutatók hangszóró

Legújabb útmutatók hangszóró

Focal K2 Power M FRAK Útmutató

5 Április 2025

Match UP C42BMW-FRT.3 Útmutató

3 Április 2025

Turbosound PQ12-SB Útmutató

3 Április 2025

Trust Tytan GXT 658 Útmutató

3 Április 2025

Turbosound PQ15-YB Útmutató

3 Április 2025

Klipsch Synergy KSB-S1 Útmutató

3 Április 2025

Klipsch Synergy KSF-10.5 Útmutató

3 Április 2025

Klipsch kO-R1 Útmutató

3 Április 2025

Klipsch Synergy SB-1 Útmutató

3 Április 2025

Klipsch Reference RB-5 II Útmutató

3 Április 2025