Használati útmutató NOCO Genius G2600

NOCO nincs kategorizálva Genius G2600

Olvassa el alább 📖 a magyar nyelvű használati útmutatót NOCO Genius G2600 (136 oldal) a nincs kategorizálva kategóriában. Ezt az útmutatót 4 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/136
EN
User Guide & Warranty
DANGER
READ AND UNDERSTAND ALL SAFETY INFORMATION BEFORE USING THIS
PRODUCT. Failure to follow these safety instructions may result in ELECTRICAL
SHOCK, EXPLOSION, FIRE, which may result in a SERIOUS INJURY, DEATH, or
PROPERTY DAMAGE.
Electrical Shock. Product is an electrical device that can shock and cause serious injury. Do
not cut power cords. Do not submerge in water or get wet.
Explosion. Unmonitored, incompatible, or damaged batteries can explode if used with product.
Do not leave product unattended while in use. Do not attempt to charge a damaged or frozen
battery. Use product only with batteries of recommended voltage. Operate product in well
ventilated areas.
Fire. Product is an electrical device that emits heat and is capable of causing burns. Do not
cover product. Do not smoke or use any source of electrical spark or fire when operating
product. Keep product away from combustible materials.
Eye Injury. Wear eye protection when operating product. Batteries can explode and cause flying
debris. Battery acid can cause eye and skin irritation. In the case of contamination of eyes or
skin, flush affected area with running clean water and contact poison control immediately.
Explosive Gases. Working in the vicinity of a lead-acid is dangerous. Batteries generate
explosive gases during normal battery operation. To reduce risk of battery explosion, follow
all safety information instructions and those published by the battery manufacturer and
manufacturer of any equipment intended to be used in the vicinity of battery. Review cautionary
markings on these products and on engine.
G26000EU
www. /supportno.co
For more information
and support visit:
About G26000. The G26000 recharges all types of 12V lead-acid and 12V lithium-ion batteries, including Wet (Flooded), Gel, MF (Maintenance-
Free), CA (Calcium), EFB (Enhanced Flooded Battery), AGM (Absorption Glass Mat), and LIB (Lithium-Ion) batteries up to 400 amp-hours.
In addition, perfect for maintenance charging of all battery sizes. Before using the charger, carefully read the battery Getting Started.
manufacturer’s specific precautions and recommended rates of charge for the battery. Make sure to determine the voltage and chemistry of the
battery by referring to your battery owner’s manual prior to charging. The G26000 has four (4) external holes for mounting. Mount Mounting.
the charger in a desired location with #10 self-drill screws. Make sure there are no obstructions behind the mounting surface. It is important
to keep in mind the distance to the battery. The DC cable length from the charger is approximately 75-inches (1,900mm). Allow for 12-inches
(304mm) of slack between connections. Battery posts, terminals, and related accessories contain chemicals, including lead. Proposition 65.
These materials are known to the State of California to cause cancer and birth defects and other reproductive harm. Personal Precaution.
Only use product as intended. Someone should be within range of your voice or close enough to come to your aid in case of emergency. Have
a supply of clean water and soap nearby in the case of battery acid contamination. Wear complete eye protection and protective clothing while
working near a battery. Always wash hands after handling batteries and related materials. Do not handle or wear any metal objects when working
with batteries including; tools, watches or jewelry. If metal is dropped onto battery, it may spark or create a short circuit resulting in electrical
shock, fire, explosion which may result in injury, death or property damage. If the product is intended by “Purchaser” to be used by a Minors.
minor, purchasing adult agrees to provide detailed instructions and warnings to any minor prior to use. Failure to do so is the sole responsibility
of the “Purchaser,” who agrees to indemnify NOCO for any unintended use or misuse by a minor. Accessories may present a Choking Hazard.
choking hazard to children. Do not leave children unattended with product or any accessory. The product is not a toy. Handle product Handling.
with care. The product can become damaged if impacted. Do not use a damaged product, including, but not limited to, cracks to the casing or
damaged cables. Do not use product with a damaged power cord. Humidity and liquids may damage product. Do not handle product or any
electrical components near any liquid. Store and operate product in dry locations. Do not operate product if it becomes wet. If product is already
operating and becomes wet, disconnect it from the battery and discontinue use immediately. Do not disconnect the product by pulling on the
cables. Do not attempt to alter, modify or repair any part of the product. Disassembling product may cause injury, death or Modifications.
damage to property. If product becomes damaged, malfunctions or comes in contact with any liquid, discontinue use, and contact NOCO. Any
modifications to the product will void your warranty. This product is only approved for use with NOCO accessories. NOCO is not Accessories.
responsible for user safety or damage when using accessories not approved by NOCO. Prevent battery acid from coming in contact Location.
with the product. Do not operate the product in a closed-in area or an area with restricted ventilation. Do not set a battery on top of product.
Position cable leads to avoid accidental damage by moving vehicle parts (including hoods and doors), moving engine parts (including fan blades,
belts, and pulleys), or what could become a hazard that may cause injury or death. Operating Temperature.This product is designed to work
in ambient temperatures between 32° and 104° F (0° and 40° C). Do not operate outside of temperature ranges. Do not charge a frozen battery.
Discontinue use of product immediately if the battery becomes excessively warm. Do not use or store your product in areas with Storage.
high concentrations of dust or airborne materials. Store your product on flat; secure surfaces so it’s not prone to falling. Store your product in
a dry location. The storage temperature is -20ºC - 25ºC (average temperature). Never exceed 80ºC under any condition. Compatibility. The
Important Safety Warnings
EN
product is only compatible with 12V & 24-volt lead-acid batteries only. Do not attempt to use product with any other type of battery. Charging
other battery chemistries may result in injury, death or property damage. Contact the battery manufacturer prior to attempting to charge
the battery. Do not charge a battery if you are unsure of the battery’s specific chemistry or voltage. Product may emit Medical Devices.
electromagnetic fields. Product contains magnetic components which may interfere with pacemakers, defibrilators, or other medical devises.
These electromagnetic fields may interfere with pacemakers or other medical devices. Consult with your physician prior to use if you have any
medical device including pacemakers. If you suspect the product is interfering with a medical device, stop using the product immediately and
consult your physician. If you have any medical condition that you believe could be affected by product, including but not Medical Conditions.
limited to; seizures, blackouts, eyestrain or headaches, consult your physician prior to use of product. Misusing a lithium-ion Lithium Charging.
battery may cause the battery to get hot, rupture, or ignite, causing serious injury, death or property damage. Not all lithium-ion batteries are
the same chemistry or contain battery management systems. Contact the lithium-ion battery manufacturer before attempting to charge. The
“Purchaser” assumes all risks associated with lithium-ion batteries. Power off the product before attempting any maintenance or Cleaning.
cleaning. Clean and dry product immediately if it comes in contact with liquid or any type of contaminant. Use a soft, lint-free (microfiber) cloth.
Avoid getting moisture in openings. Explosive Atmospheres. Obey all signs and instructions. Do not operate product in any area with a
potentially explosive atmosphere, including fueling areas or areas which contain chemicals or particles such as grain, dust or metal powders.
High-Consequence Activities. This product is not intended for use where the failure of the product could lead to injury, death or severe
environmental damage. Radio Frequency Interference. Product is designed, tested, and manufactured to comply with regulations governing
radio frequency emissions. Such emissions from the product can negatively affect the operation of other electronic equipment, causing them to
malfunction. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: Model Number: G26000
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
Charging Modes.
The G26000 has eleven (11) modes plus JumpCharge for engine starting. Charge modes after the red line require a three (3) second hold to
activate the mode. It is essential to understand the differences and purpose of each charge mode. Do not operate the charger until you confirm
the appropriate charge mode for your battery. Below is a brief description:
How To Use
Explanation
No Power
14.5V | 26A | Up to 500Ah Batteries
In Standby mode, the charger is not charging or providing any power to the battery. Energy Save is activated during this
mode, drawing microscopic power from the electrical outlet. When selected, an orange LED will illuminate.
For charging 12-volt Wet Cell, Gel Cell, Enhanced Flooded, Maintenance-Free and Calcium batteries. When selected, a
white LED will illuminate.
For charging 24-volt Wet Cell, Gel Cell, Enhanced Flooded, Maintenance-Free and Calcium batteries. When selected, a
white LED will illuminate.
29V | 13A | Up to 250Ah Batteries
For charging 24-volt batteries in cold temperatures below 50ºF (10ºC) or AGM batteries. When selected, a blue
LED will illuminate.
29.6V | 13A | Up to 250Ah Batteries
For charging 12-volt batteries in cold temperatures below 50ºF (10ºC) or AGM batteries. When selected, a blue LED will
illuminate.
14.8V | 26A | Up to 500Ah Batteries
For charging 12-volt lithium-ion batteries, including lithium iron phosphate. When selected, a blue LED will illuminate.
14.2V | 26A | Up to 500Ah Batteries
Mode
12V
NORM
Standby
24V
NORM
24V
COLD/AGM
12V
COLD/AGM
12V
LITHIUM
Press & Hold
12V
AGM+
Press & Hold
For charging 12-volt advanced AGM batteries, which requires a higher than normal charging voltage. When selected, a
blue LED will illuminate.
15.5V | 26A | Up to 500Ah Batteries
16V
LITHIUM
Press & Hold
For charging 16-volt lithium-ion batteries, including lithium iron phosphate, which are commonly used in racing vehicles.
When selected, a blue LED will illuminate.
19.45V | 20A | Up to 250Ah Batteries
EN
Using 12V Lithium. [Press & Hold]
12V Lithium charge mode is designed for 12-volt lithium-ion batteries only, including lithium iron phosphate. USE THIS MODE CAUTION.
WITH CARE. THIS MODE IS FOR 12-VOLT LITHIUM BATTERIES ONLY. LITHIUM-ION BATTERIES ARE MADE AND CONSTRUCTED IN
DIFFERENT WAYS AND SOME MAY OR MAY NOT CONTAIN A BATTERY MANAGEMENT SYSTEM (BMS). CONSULT THE LITHIUM BATTERY
MANUFACTURER BEFORE CHARGING AND ASK FOR RECOMMENDED CHARGING RATES AND VOLTAGES. SOME LITHIUM-ION
BATTERIES MAY BE UNSTABLE AND UNSUITABLE FOR CHARGING. MAKE SURE YOU PURCHASE YOUR LITHIUM-ION BATTERY FROM A
WELL-KNOWN AND REPUTABLE BRAND.
Using 12V AGM+. [Press & Hold]
12V AGM+ charge mode is designed for 12-volt advanced AGM batteries only. Advanced AGM batteries are a new battery technology typically
found in startstop micro-hybrid vehicles. These batteries accept a higher than normal charging voltage around 15.5-volts. 12V AGM+ charge
mode is NOT suitable for traditional AGM batteries. Consult the battery manufacturer before using this mode. USE THIS MODE CAUTION.
WITH CARE. THIS MODE IS FOR 12-VOLT LEAD-ACID ADVANCED AGM BATTERIES ONLY. THIS MODE USES A HIGH CHARGING VOLTAGE
AND MAY CAUSE SOME WATER LOSS IN WET (FLOODED) CELL BATTERIES OR OVERCHARGE IN SOME BATTERIES.
Using 16V Lithium. [Press & Hold]
16V Lithium charge mode is for 16V lithium-ion batteries only, including lithium iron phosphate batteries. 16-volt lithium-ion batteries are
commonly found in racing vehicles, where the alternator might be removed, or used to improve the performance of the injector or fuel pump.
CAUTION. THIS MODE IS FOR 16-VOLT LITHIUM BATTERIES ONLY. LITHIUM-ION BATTERIES ARE MADE AND CONSTRUCTED IN
DIFFERENT WAYS AND SOME MAY OR MAY NOT CONTAIN A BATTERY MANAGEMENT SYSTEM (BMS). CONSULT THE LITHIUM BATTERY
MANUFACTURER BEFORE CHARGING AND ASK FOR RECOMMENDED CHARGING RATES AND VOLTAGES. SOME LITHIUM-ION
BATTERIES MAY BE UNSTABLE AND UNSUITABLE FOR CHARGING.
Using 16V AGM. [Press & Hold]
16V
AGM
Press & Hold
For charging 16-volt AGM batteries, which are commonly used in racing vehicles. When selected, a blue LED
will illuminate.
19.6V | 20A | Up to 250Ah Batteries
13.6V
SUPPLY
Press & Hold
Converts to a DC power supply for powering any 12VDC device, like a tire inflator, oil changer, or as a memory retainer
when replacing a battery. When selected, a red LED will illuminate.
13.6V | 5A | Max 6A
12V
REPAIR
Press & Hold
An advanced battery recovery mode for repairing and storing, old, idle, damaged, stratified or sulfated batteries. When
selected, a red LED will illuminate and flash
16.5V | 1.5A | Any Capacity
16V AGM charge mode is for 16V AGM batteries only. 16-volt AGM batteries are commonly found in racing vehicles, where the alternator might
be removed, or used to improve the performance of the injector or fuel pump. USE THIS MODE WITH CARE. THIS MODE IS FOR CAUTION.
16-VOLT AGM BATTERIES ONLY. DO NOT USE ON A 12-VOLT BATTERY. CONSULT THE BATTERY MANUFACTURER BEFORE CHARGING
AND ASK FOR RECOMMENDED CHARGING RATES AND VOLTAGES.
Using 13.6V Supply. [Press & Hold]
13.6V Supply converts the charger to a constant current, constant voltage DC power supply. It can be used to power 12VDC devices, including;
tire inflators, oil changers, coffee pots, seat heaters and more. As a power supply, it can also be used to retain a vehicle’s on-board computer
settings during battery repair or replacement. 13.6V Supply provides 13.6-volts at 5A with overload protection at 6A (Max). THIS CAUTION.
MODE IS FOR 12-VOLT LEAD-ACID BATTERIES ONLY. PRIOR TO USE, READ YOUR12VDC DEVICE MANUAL TO DETERMINE IF IT IS
SUITABLE FOR USE WITH THIS MODE. BOTH THE SPARK PROOF AND REVERSE POLARITY SAFETY FEATURES ARE DISABLED IN THIS
MODE. DO NOT ALLOW THE POSITIVE AND NEGATIVE BATTERY CLAMP OR EYELET TERMINAL CONNECTORS TO TOUCH OR CONNECT
TO EACH OTHER AS THE CHARGER COULD GENERATE SPARKS. CHECK THE POLARITY OF THE BATTERY TERMINALS BEFORE USING
THIS MODE.
JumpCharge.
JumpCharge is a feature for jumpstarting low-voltage or dead vehicle batteries. JumpCharge uses precision charge control to avoid overloading
the battery that shortens the life of your battery. To operate JumpCharge, the charger must be connected to a 12-volt battery with the Battery
Clamp Connectors connected. Press the JumpCharge button to begin jumpstarting your vehicle. Once initiated, the Charge LEDs will begin
showing the progress of the JumpCharge from 25% to 100%. When using this mode, the Charge LEDs do not display the battery’s state-
of-charge (SOC), only the JumpCharge progress. USE THIS MODE WITH CARE. THIS MODE IS FOR 12-VOLT LEAD-ACID CAUTION.
BATTERIES ONLY. DO NOT USE JUMPCHARGE MORE THAN TWO (2) TIMES WITHIN A TWENTY-HOUR (24) HOUR PERIOD. IF TWO (2)
JUMPCHARGES CANNOT SUCCESSFULLY START YOUR VEHICLE, HAVE YOUR BATTERY EVALUATED BY A PROFESSIONAL.
Connecting to the Battery.
Do not connect the AC cable until the connection of the battery is made first. Do not make any connections to the carburetor, fuel lines, or thin
sheet metal parts. The below instructions are for a negative ground system. If a positive ground system (very uncommon), follow the below
instructions in reverse order.
1.) Connect the positive (red) battery connector to the positive (POS,P,+) battery terminal.
2.) Connect the negative (black) battery connector to the negative (NEG,N,-) battery terminal or vehicle chassis.
Jump
CHARGE
Delivers 20A for five (5) minutes to jumpstart your dead vehicle battery. When selected, a white LED will illuminate.
(Red Manual Mode)
5Min | 20A | Up to 500Ah Batteries
EN
LED Explanation
25%
Red LED
The 25% Charge LED will slowly pulse “on” and “off”, when the battery is less than 25% fully charged. When
the battery is 25% charged, the red Charge LED will be solid.
75%
Orange LED
The 75% Charge LED will slowly pulse “on” and “off”, when the battery is less than 75% fully charged. When
the battery is 75% charged, the orange Charge LED will be solid.
The 50% Charge LED will slowly pulse “on” and “off”, when the battery is less than 50% fully charged. When
the battery is 50% charged, the red Charge LED will be solid.
100%
Green LED
The 100% Charge LED will slowly pulse “on” and “off”, when the battery is less than 100% fully charged.
When the battery is fully charged, the green LED will be solid, and the 25%, 50% and 75% Charge LEDs
will turn “off”.
50%
Red LED
25% 50% 75% 100%
25% 50% 75% 100%
25% 50% 75% 100%
25% 50% 75% 100%
3.) Connect the battery charger’s AC power plug into a suitable electrical outlet.
4.) When disconnecting the battery charger, disconnect in the reverse sequence.
Begin Charging.
1.) Verify the voltage and chemistry of the battery.
2.) Confirm you are properly connected to the battery and plugged into an AC electrical outlet.
3.) The charger begins in Standby mode (Orange LED), and not providing any power.
4.) Press the mode button to toggle to the appropriate charge mode for the voltage and chemistry of your battery.
5.) The mode LED will illuminate the selected charge mode and the Charge LEDs will illuminate indicating the charging process has started.
6.) The charger is now charging and can be left connected to the battery.
Understanding Charge LEDs.
The charger has four (4) state-of-charge LEDs - 25%, 50%, 75% and 100%. See the explanation below:
Understanding Advanced Diagnostics.
Advanced Diagnostics displays charging errors by flashing Error LED and Standby LED flashing back and forth. The number of flashes between
each pulse denotes the potential Error Condition (except reverse polarity and low-voltage battery).
Error Reason/Solution
Single Flash The battery will not hold a charge. Replace battery.
Battery short. Replace battery.
Battery voltage is too high. Check the battery voltage and charge mode.
Error LED Solid Red Reverse battery connections.
Battery voltage is too low to detect the battery. Jump start the battery to raise the battery voltage.
Double Flash
Triple Flash
Standby Solid Orange
Battery Size Approx. Time to Charge In Hours
12V 24VAh
Charging Times.
The estimated charge times are based on an average depth of discharge to a fully charged battery. Actual data may differ due to battery
conditions.
50
75
100
150
200
1.0
1.4
1.9
2.9
3.8
1.9
2.9
3.8
5.8
7.7
Maintenance
Green LED
25% 50% 75% 100%
During maintenance charging, the 100% Charge LED will pulse “on” and “off” slowly. When the battery is
topped off and fully charged again, the 100% Charge LED will turn solid green. The charger can be left
connected to the battery indefinitely.
NOCO’S LIABILITY HEREUNDER IS EXPRESSLY LIMITED TO REPLACEMENT OR REPAIR. TO THE MAXIMUM EXTENT PERMITTED BY LAW, NOCO
SHALL NOT BE LIABLE TO ANY PURCHASER OF THE PRODUCT OR ANY THIRD PARTY FOR ANY SPECIAL, INDIRECT, CONSEQUENTIAL OR
EXEMPLARY DAMAGES, INCLUDING, BUT NOT LIMITED TO, LOST PROFITS, PROPERTY DAMAGE OR PERSONAL INJURY, RELATED IN ANY WAY
TO THE PRODUCT, HOWSOEVER CAUSED, EVEN IF NOCO HAD KNOWLEDGE OF THE POSSIBILITY OF SUCH DAMAGES. THE WARRANTIES SET
FORTH HEREIN ARE IN LIEU OF ALL OTHER WARRANTIES, EXPRESS, IMPLIED, STATUTORY OR OTHERWISE, INCLUDING, WITHOUT LIMITATION,
THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, AND THOSE ARISING FROM COURSE OF
DEALING, USAGE OR TRADE PRACTICE. IN THE EVENT THAT ANY APPLICABLE LAWS IMPOSE WARRANTIES, CONDITIONS OR OBLIGATIONS
THAT CANNOT BE EXCLUDED OR MODIFIED, THIS PARAGRAPH SHALL APPLY TO THE GREATEST EXTENT ALLOWED BY SUCH LAWS.
This Limited Warranty is made solely for the benefit of the original purchaser of the Product from NOCO or from a NOCO approved reseller or distributor
and is not assignable or transferable. To assert a warranty claim, the purchaser must: (1) request and obtain a return merchandise authorization (“RMA”)
number and return location information (the “Return Location”) from NOCO Support by emailing or by calling 1.800.456.6626; and support@no.co
(2) send the Product, including RMA number, receipt or a warranty fee (fee required only if not providing receipt) of 45% of MSRP of the defective
Product (the “Warranty Fee”) [RMA will include applicable Warranty Fee amount] to the Return Location. DO NOT SEND IN PRODUCT WITHOUT FIRST
OBTAINING AN RMA FROM NOCO SUPPORT.
THE ORIGINAL PURCHASER IS RESPONSIBLE (AND MUST PREPAY) ALL PACKAGING AND TRANSPORTATION COSTS TO SHIP PRODUCTS FOR
WARRANTY SERVICE.
NOTWITHSTANDING THE ABOVE, THIS LIMITED WARRANTY IS VOID AND DOES NOT APPLY TO PRODUCTS THAT: (a) are misused, mishandled,
subjected to abuse or careless handling, accident, improperly stored, or operated under conditions of extreme voltage, temperature, shock, or vibration
beyond NOCO’s recommendations for safe and effective use; (b) improperly installed, operated or maintained; (c) are/were modified without the express
written consent of NOCO; (d) have been disassembled, altered or repaired by anyone other than NOCO; (e) the defects of which were reported after
the Warranty Period.
THIS LIMITED WARRANTY DOES NOT COVER: (1) normal wear and tear; (2) cosmetic damage that does not affect functionality; or (3) Products where
the NOCO serial number is missing, altered, or defaced.
You may register your NOCO product online at: no.co/register. If you have any questions regarding your warranty or product, contact NOCO Support
(email and phone number above) or write to: The NOCO Company, at 30339 Diamond Parkway, #102, Glenwillow, OH 44139 USA.
déclencher le mode. Ces modes “appuyer et maintenir” sont des modes de chargement avancés qui retiendront toute votre attention avant
de les déclencher. “Appuyer et charger” sont indiqués sur le chargeurs sur une ligne rouge. Il est important de comprendre les différences et
les avantages de chaque mode de chargement. Il est important de charger jusqu’à ce que vous confirmiez le mode de chargement de votre
batterie. Ci-dessous se trouve une brève description :
Explication
No Power
14.5V | 26A | Jusqu’à 500Ah Batterie
En mode veille, le chargeur ne charge pas ou ne fournit aucune électricité à la batterie. Le mode économie d’énergie
est activé durant ce mode et s’alimente à très petites doses sur la prise de courant. Lorsqu’il est choisi, un LED orange
s’allume.
Pour charger une batterie humide, à gel, EFB (enhanced flooded batteriy), sans entretien et au calcium. Lorsqu’il est
choisi, un LED blanc s’allume.
Pour charger une batterie 24 volt humide, à gel, EFB (enhanced flooded batteriy), sans entretien et au calcium. Lorsqu’il
est choisi, un LED blanc s’allume.
29V | 13A | 250Ah BatterieJusqu’à
Pour charger des batteries de 24 volts à des températures en-dessous de 10° C ou des batteries AGM. Lorsqu’il est
choisi, un LED bleu s’allume.
29.6V | 13A | 250Ah BatterieJusqu’à
Pour charger des batteries de 12 volts à des températures en-dessous de 10° C ou des batteries AGM. Lorsqu’il est
choisi, un LED bleu s’allume.
14.8V | 26A | Jusqu’à 500Ah Batterie
Pour charger des batteries 12 volt lithium-ions, y compris lithium fer phosphate. Lorsqu’il est choisi, un LED bleu
s’allume.
14.2V | 26A | Jusqu’à 500Ah Batterie
Modo
12V
NORM
Standby
24V
NORM
24V
COLD/AGM
12V
COLD/AGM
12V
LITHIUM
Appuyer & maintenir
Pour charger des batteries AGM 12 volt qui requièrent une tension de chargement supérieure à la
normale. Lorsqu’il est choisi, un LED bleu s’allume.
15.5V | 26A | Jusqu’à 500Ah Batterie
12V
AGM+
Appuyer & maintenir
de la pompe à carburant ou de l’injecteur. ATTENTION. CE MODE EST UNIQUEMENT ADAPTÉ À DES BATTERIES PLOMBACIDE 16 VOLT.
LES BATTERIES LITHIUM-IONS SONT FABRIQUÉES DE MANIÈRES DIFFÉRENTES ET CERTAINES CONTIENNENT OU NON DES SYSTÈMES
DE GESTION DE BATTERIES (BMS). CONSULTEZ LE FABRICANT DE BATTERIES LITHIUM AVANT DE CHARGER ET RENSEIGNEZ-VOUS
SUR LES TAUX DE CHARGEMENT ET DE TENSION. CERTAINES BATTERIES LITHIUM-IONS PEUVENT ÊTRE INSTABLES ET INADAPTÉES
AU CHARGEMENT.
Utilisation du mode de chargement AGM 16V. Appuyer & maintenir
Le mode de chargement 16V AGM est uniquement adapté à des batteries 16V AGM. Les batteries 16 volt AGM se trouvent habituellement dans
des véhicules de course, où l’alternateur peut être enlevé, ou utilisé pour améliorer la performance de la pompe à carburant ou de l’injecteur.
ATTENTION. UTILISEZ CE MODE AVEC PRÉCAUTION. CE MODE EST UNIQUEMENT ADAPTÉ À DES BATTERIES AGM 16 VOLT. NE PAS
UTILISER AVEC UNE BATTERIE 12 VOLTS. CONSULTEZ LE FABRICANT DE BATTERIES AVANT DE CHARGER ET RENSEIGNEZ-VOUS SUR
LES TAUX DE CHARGEMENT ET DE TENSION.
Utilisation du mode de chargement alimentation 13.6 V. Appuyer & maintenir
Le mode 13.6 V convertit le chargeur en source d’alimentation DC de courant et de tension constants. Il peut être utilisé pour alimenter les
appareils 12 VDC, y compris : des gonfleurs de pneu, des changeurs d’huile, des chauffe-siège et bien plus. En tant qu’alimentation, il peut
également être utilisé pour sauvegarder les paramétrages d’un ordinateur de bord de véhicule pendant la réparation ou le remplacement
d’une batterie. Le mode 13.6V fournit du courant 13.6 volt à 5 ampères avec une protection de surcharge à 6 ampères (max). ATTENTION.
CE MODE EST UNIQUEMENT ADAPTÉ À DES BATTERIES PLOMBACIDE 12 VOLT. AVANT TOUTE UTILISATION, LISEZ LE MANUEL
D’UTILISATION 12VDC POUR DÉTERMINER S’IL EST ADAPTÉ À UNE UTILISATION AVEC CE MODE. DANS CE MODE, LA POLARITÉ
INVERSÉE ET LA PROTECTION ÉTINCELLES SONT DÉSACTIVÉS. N’AUTORISEZ PAS LA BRIDE DE SERRAGE NÉGATIVE ET POSITIVE OU
LES CONNECTEURS DE BORNES À OEIL DE SE TOUCHER OU DE SE CONNECTER COMME LE CHARGEUR POURRAIT GÉNÉRER DES
ÉTINCELLES. VÉRIFIEZ LA POLARITÉ DES BORNES DE LA BATTERIE AVANT D’UTILISER CE MODE.
Chargement Jump.
Le chargement jump est une fonctionnalité pour le démarrage express de batteries de véhicules à basse tension ou mortes. Le chargement
jump utilise un contrôle du chargement précis pour éviter une surcharge de la batterie qui diminue la durée de vie de votre batterie. Pour utiliser
le chargement jump, le chargeur doit être connecté à une batterie 12 volts avec les brides de serrage connectés. Pressez le bouton chargement
jump pour commencer le démarrage express de votre véhicule. Une fois initié, les LEDs de chargement commenceront à montrer le progrès
du chargement jump de 25 à 100 %. En utilisant ce mode, les LEDs de chargement ne montreront pas l’état du chargement (SOC - state
of charge), mais seulement la progression du chargement jump. ATTENTION. UTILISEZ CE MODE AVEC PRÉCAUTION. CE MODE EST
UNIQUEMENT ADAPTÉ À DES BATTERIES PLOMBACIDE 12 VOLT. N’UTILISEZ PAS LE CHARGEMENT JUMP PLUS DE DEUX (2) FOIS DANS
UN INTERVALLE DE VINGTQUATRE (24) HEURES. SI DEUX (2) CHARGEMENTS JUMP NE PEUVENT PAS DÉMARRER VOTRE VÉHICULE,
ÉVALUEZ VOTRE BATTERIE PAR UN MAGASIN DE BATTERIE PROCHE DE CHEZ VOUS.
FR
Connecter la batterie.
Ne connectez pas la prise de courant AC jusqu’à ce que toutes les autres connections soient faites. Identifiez la bonne polarité des bornes de la
batterie sur la batterie. La borne positive de la batterie est généralement indiquée par ces lettres ou symboles (POS, P, +). La borne négative de
la batterie est généralement indiquée par ces lettres ou symboles (NEG, N, -). Ne connectez pas le carburateur, les conduites de carburant, ou
bien des parties fines en métal. Les instructions ci-dessous sont pour une batterie avec masse négative (cas le plus courant). Si votre véhicule
dispose d’une masse positive (cas très rare) suivez les instructions en sens inverse.
1.) Connectez la bride de serrage positive (rouge) sur la borne positive (POS, P, +) de la batterie.
2.) Connectez la bride de serrage négative (noire) avec la borne négative (NEG, N, -) de la batterie ou avec le châssis du véhicule.
3.) Branchez la prise de courant AC de la batterie dans une prise électrique murale adaptée. Ne faites pas face à la batterie lors de cette
opération.
4.) Quand vous déconnectez le chargeur de la batterie, déconnectez les brides dans le sens inverse en commençant par la négative (ou bien
par la positive en cas de masse positive).
Commencez le chargement.
1.) Vérifiez la tension et la composition chimique de la batterie.
2.) Confirmez que vous avez bien connecté les brides de serrages ou les connecteurs de bornes à oeil correctement et que la prise de courant
est bien branché sur le secteur.
3.) Le chargeur commencera par un mode veille, indiqué par un LED orange. En mode veille, le chargeur ne fournit pas d’électricité.
4.) Appuyez sur le bouton mode pour passer au mode de chargement approprié (appuyez et maintenez pour trois secondes pour débuter un
mode de chargement avancé) pour la tension et la composition chimique de la batterie.
5.) Les LEDs correspondant au mode de chargement s’allumeront, ainsi que les LEDs indiquant la progression du chargement (selon l’état de
la batterie).
6.) Le chargeur peut maintenant rester connecté à la batterie à tout moment pour fournir un chargement d’entretien.
Jump
CHARGE
Fournit 30A pour cinq (5) minutes pour charger d’un coup votre batterie 12 volts morte. Lorsqu’il est choisi, un LED
blanc s’allume. (Mode manuel rouge)
5Min | 20A | 500Ah Jusqu’à Batterie
G26000EU
Deutsch
Benutzerhinweise und Garantie
GEFAHR
LESEN UND VERSTEHEN SIE DIESE SICHERHEITSHINWEISE VOR GEBRAUCH DES PRODUKTS.
Die Nichtbefolgung dieser Sicherheitshinweise kann STROMSCHLÄGE, EXPLOSIONEN, oder FEUER
verursachen, was SCHWERE VERLETZUNGEN, TOD, oder SACHSCHÄDEN zur Folge haben kann.
Stromschlag. Das Produkt ist ein elektrisches Gerät, welches Stromschläge und ernsthafte
Verletzungen verursachen kann. Zerschneiden oder beschädigen Sie nicht die Netzkabel. Tauchen
Sie das Gerät nicht unter Wasser und halten Sie es von Feuchtigkeit fern.
Explosion. Nicht überwachte, inkompatible oder beschädigte Batterien können bei der Benutzung
mit dem Produkt zu einer Explosion führen. Lassen Sie das Produkt während des Betriebs nicht
unbeaufsichtigt. Versuchen Sie nicht, eine eingefrorene oder beschädigte Batterie fremdzustarten.
Verwenden Sie das Produkt nur mit Batterien mit der empfohlenen Spannung. Verwenden Sie das
Produkt nur in gut belüfteten Bereichen.
Feuer. Das Produkt ist ein elektrisches Gerät, welches Hitze erzeugt und Verbrennungen
verursachen kann. Decken Sie das Produkt nicht ab. Rauchen Sie nicht und benutzen Sie keinerlei
Gegenstände, die elektrische Funken oder Feuer erzeugen, während Sie das Produkt bedienen.
Halten Sie das Produkt fern von brennbaren Materialien.
Verletzungen am Auge. Tragen Sie bei der Bedienung des Produkts einen Augenschutz. Batterien
können explodieren und herumfliegende Teile können Sie verletzen. Batteriesäure kann zu Augen-
und Hautirritationen führen. Sollte Batteriesäure in die Augen oder auf die Haut gelangen, spülen
Sie den betroffenen Bereich mit laufendem klarem Wasser aus und kontaktieren Sie umgehend den
Giftnotruf.
Explosive Gase. In der Nähe von Bleibatterien zu arbeiten ist gefährlich. Batterien erzeugen
explosive Gase während des normalen Betriebs. Um das Risiko einer Batterieexplosion zu senken,
befolgen Sie alle Sicherheitsanweisungen sowie die Sicherheitshinweise des Batterieherstellers und
der Hersteller von jeglichem Zubehör, das in der Nähe der Batterie verwendet wird. Überprüfen Sie
die Warnhinweise auf diesem Produkt und auf dem Motor.
Weitere Informationen und
Kundensupport unter:
www. /supportno.co

Termékspecifikációk

Márka: NOCO
Kategória: nincs kategorizálva
Modell: Genius G2600

Szüksége van segítségre?

Ha segítségre van szüksége NOCO Genius G2600, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók nincs kategorizálva NOCO

NOCO

NOCO XGrid XGB6 Útmutató

14 Szeptember 2024
NOCO

NOCO Genius GEN Mini 3 Útmutató

5 Augusztus 2024
NOCO

NOCO Genius G1100 Útmutató

4 Augusztus 2024
NOCO

NOCO ChargeLight CL3 Útmutató

3 Augusztus 2024
NOCO

NOCO Genius GEN3 Útmutató

1 Augusztus 2024
NOCO

NOCO XGrid XGB12 Útmutató

31 Július 2024
NOCO

NOCO Genius GEN4 Útmutató

30 Július 2024
NOCO

NOCO XGrid XGB3L Útmutató

28 Július 2024
NOCO

NOCO Genius GB30 Útmutató

28 Július 2024
NOCO

NOCO XGrid XGB3 Útmutató

27 Július 2024

Útmutatók nincs kategorizálva

Legújabb útmutatók nincs kategorizálva

MOZA

MOZA SR-P Útmutató

10 Április 2025
Soundstream

Soundstream VRN-64HBL Útmutató

10 Április 2025
Panasonic

Panasonic Lumix DMW-AC11 Útmutató

10 Április 2025
Planet

Planet PWR-240-48 Útmutató

9 Április 2025
CaterChef

CaterChef 445001 Útmutató

9 Április 2025
IFM

IFM E40581 Útmutató

9 Április 2025
Livn

Livn Bolt Útmutató

9 Április 2025
Livn

Livn Beats Útmutató

9 Április 2025
Alpine

Alpine DP2-40C-BC Útmutató

9 Április 2025
IFM

IFM O3R252 Útmutató

9 Április 2025