Használati útmutató Milwaukee 8950

Milwaukee porszívó 8950

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Milwaukee 8950 (15 oldal) a porszívó kategóriában. Ezt az útmutatót 13 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF

Oldal 1/15

TO REDUCE THE RISK OF INJURY, USER MUST READ AND UNDERSTAND OPERATOR'S

MANUAL.

AFIN DE RÉDUIRE LE RISQUE DE BLESSURES, L'UTILISATEUR DOIT LIRE ET BIEN

COMPRENDRE LE MANUEL DE L'UTILISATEUR.

PARA REDUCIR EL RIESGO DE LESIONES, EL USUARIO DEBE LEER Y ENTENDER EL

MANUAL DEL OPERADOR.

OPERATOR'S MANUAL

MANUEL de L'UTILISATEUR

MANUAL del OPERADOR

HEAVY-DUTY COMMERCIAL VACUUM

EXTRA ROBUSTE ASPIRATEUR COMMERCIAL

HEAVY-DUTY ASPIRADORA COMMERCIAL

Cat. No.

No de cat.

8936-20

8938-20

8950

8955

WARNING - TO REDUCE

THE RISK OF FIRE, ELECTRIC SHOCK OR

INJURY:

• Do not leave appliance when plugged in. Un-

plug from outlet when not in use and before

servicing. Connect to a properly grounded

outlet only. See Grounding Instructions.

• Do not expose to rain – store indoors.

• Do not allow to be used as a toy. Close attention

is necessary when used by or near children.

• Use only as described in this manual. Use only

manufacturer’s recommended attachments.

• Do not use with damaged cord or plug. If ap-

pliance is not working as it should, has been

dropped, damaged, left outdoors, or dropped

into water, return it to a service center.

• Do not pull or carry by cord, use cord as a

handle, close a door on cord, or pull cord

around sharp edges or corners. Do not run

appliance over cord. Keep cord away from

heated surfaces.

• Do not unplug by pulling on cord. To unplug

grasp the plug not the cord.

• Do not handle plug or appliance with wet hands.

• Do not put any object into openings. Do not use

with any opening blocked; keep free of dust, lint,

hair, and anything else that may reduce air ﬂ ow.

• Keep hair, loose clothing, ﬁ ngers, and all parts

of body away from openings and moving parts.

• Do not pick up anything that is burning or

smoking such as cigarettes, matches, or hot

ashes.

• Do not use without dust bag and/or ﬁ lters in

place.

• Turn off all controls before unplugging.

• Use extra care when cleaning on stairs.

• Do not use to pick up ﬂ ammable or combus-

tible liquids such as gasoline or use in areas

where they may be present.

• Vacuum cleaners have motors and other parts

that can produce arcs or sparks during normal

use. Do not use within 20 feet of areas where

explosive gases may be present (such as gaso-

line pumps and places where liquids like paint

thinners, cleaners, solvents, etc. are stored).

• Unplug power cord whenever motor head is

removed from tank.

• Do not use in the presence of explosive liquids

or vapors.

• To reduce the risk of health hazards from

vapors or dust, do not vacuum toxic, carcino-

genic or other hazardous materials such as

asbestos, arsenic, barium, berylium, lead, pes-

ticides or other health endangering materials.

• Do not use where oxygen or anesthetics are used.

• Wear electrically insulated footwear, such as

rubber boots, when vacuuming wet material.

• Maintain labels and nameplates. These carry

important information. If unreadable or missing,

contact a MILWAUKEE service facility for a free

replacement.

• WARNING! NOTDo use this vacuum cleaner

to vacuum lead paint debris because this may-

disperse fine lead particles into the air. This

vacuum cleaner is not intended for use under EPA

Regulation 40 CFR Part 745 for lead paint material

cleanup.

• WARNING: Some dust created by power sanding,

sawing, grinding, drilling, and other construction

activities contains chemicals known to cause

cancer, birth defects or other reproductive harm.

Some examples of these chemicals are:

• lead from lead-based paint

• crystalline silica from bricks and cement and other

masonry products, and

• arsenic and chromium from chemically-treated-

lumber.

Your risk from these exposures varies, depending

on how often you do this type of work. To reduce

your exposure to these chemicals: work in a well

ventilated area, and work with approved safety

equipment, such as those dust masks that are spe-

cially designed to ﬁ lter out microscopic particles.

IMPORTANT SAFETY INSTRUCTIONS

WARNING Failure to follow the warnings and instructions may result

in electric shock, ﬁ re and/or serious injury. When using an electrical appliance,

basic precautions should always be followed, including the following: READ ALL

INSTRUCTIONS BEFORE USING THIS APPLIANCE.

READ AND

SAVE ALL

INSTRUCTIONS

FOR FUTURE USE

GROUNDING

INSTRUCTIONS

WARNING Improper

connection of the equipment-ground-

ing conductor can result in a risk of

electric shock. Check with a quali-

ﬁ ed electrician or service person if

you are in doubt as to whether the

outlet is properly grounded. Do not

modify the plug provided with the

appliance - If it will not ﬁ t the outlet,

have a proper outlet installed by a

qualiﬁ ed electrician.

This appliance must be grounded. If it should mal-

function or breakdown, grounding provides a path

of least resistance for electric current to reduce the

risk of electric shock. This appliance is equipped

with a cord having an equipment-grounding conduc-

tor and grounding plug. The plug must be inserted

into an appropriate outlet that is properly installed

and grounded in accordance with all local codes

and ordinances.

Grounded tools require a three wire extension cord.

As the distance from the supply outlet increases,

you must use a heavier gauge extension cord. Us-

ing extension cords with inadequately sized wire

causes a serious drop in voltage, resulting in loss

of power and possible tool damage. Refer to the

table shown to determine the required minimum

wire size.

The smaller the gauge number of the wire, the

greater the capacity of the cord. For example, a 14

gauge cord can carry a higher current than a 16

gauge cord. When using more than one extension

cord to make up the total length, be sure each cord

contains at least the minimum wire size required.

If you are using one extension cord for more than

one tool, add the nameplate amperes and use the

sum to determine the required minimum wire size.

Guidelines for Using Extension Cords

• If you are using an extension cord outdoors, be

sure it is marked with the sufﬁ x “W-A” (“W” in

Canada) to indicate that it is acceptable for outdoor

use.

• Be sure your extension cord is properly wired

and in good electrical condition. Always replace a

damaged extension cord or have it repaired by a

qualiﬁ ed person before using it.

• Protect your extension cords from sharp objects,

excessive heat and damp or wet areas.

* Based on limiting the line voltage drop to ﬁ ve volts at

150% of the rated amperes.

EXTENSION

CORDS

Recommended Minimum Wire Gauge

For Extension Cords*

Extension Cord Length

Nameplate

Amperes 25' 50' 75' 100' 150'

0 - 2.0

2.1 - 3.4

3.5 - 5.0

5.1 - 7.0

7.1 - 12.0

12.1 - 16.0

16.1 - 20.0

This appliance is for use on a nominal 120-volt

circuit, and has a grounded plug that looks like the

plug illustrated in . A temporary adaptor sketch A

that looks like the adaptor illustrated in sketches

B and C may be used to connect this plug to a

2-pole receptacle as shown in sketch B if a prop-

erly grounded outlet is not available. The tempo-

rary adaptor should be used only until a properly

grounded outlet ( ) can be installed by a sketch A

qualiﬁ ed electrician. The green colored rigid ear, lug

or the like extending from the adaptor must be con-

nected to a permanent ground such as a properly

grounded outlet box cover. Whenever the adaptor

is used, it must be held in place by a metal screw.

IN CANADA, THE USE OF A TEMPORARY ADAP-

TOR IS NOT PERMITTED BY THE CANADIAN

ELECTRICAL CODE. Make sure that the appli-

ance is connected to an outlet having the same

conﬁ guration as the plug. No adaptor should be

used with this appliance.

1. Handle

2. Exhaust port

3. Tank latch

4. Intake port

5. Tank

6. Utility Outlet

(Cat. No. 8936-20 only)

* For Cat. No. 8936-20 with onboard outlet: The entire unit is rated at 12 amps. The vacuum motor is rated at 9.5 amps.

The outlet on the motor head is rated at 8 amps.

Cat. No.

Volts

AC Amps For Materials

Tank Capacity

Gallons

Air Flow

Cubic Feet per Minute

Sealed Suction

in Water

8936-20

8938-20

8950

8955

120

12*

7.4

Wet or Dry

7.5

190

100

143

60"

80"

45"

WARNING To reduce

the risk of injury, always unplug tool before

changing or removing accessories. Only use

accessories speciﬁ cally recommended for

this tool. Others may be hazardous.

Assembling Dolly (Cat. No. 8955)

Assemble as shown in the diagram. You will need

a hammer and a phillips screwdriver.

Installing Handle (Cat. No. 8955)

You will need either a ﬂ at blade screwdriver or a

socket driver and a wrench or a pair of pliers.

Assembling Dolly (Cat. No. 8938-20)

Assemble as shown in the diagram. You will need:

(2) 1/2 inch open end wrenches, (2) 7/16 inch open

end wrenches, or a socket set and a hammer.

1. Place wheels on rear frame (B) by tapping in the

axle (C), ﬁ tting the wheel (D) on the axle and

tapping a cap nut (E) on with a hammer.

2. Align front frame (F) and rear frame (B) so that

they ﬁ t together and ﬁ t lip of tank (H) into the

grooves in front and rear frames.

3. Secure frame (B and F) to the tank by placing

the hex bolts (I) through the holes in dolly and

securing them with nut (L) and washer (K) as

shown.

4. Insert caster (G) and push down until caster

snaps into place.

Fig. 1 A

Fig. 2

1. Place dolly handle between tank and side handle

on either side of the tank.

2. Fasten tightly with slotted hex head screws.

Fig. 3

SPECIFICATIONS

FUNCTIONAL DESCRIPTION

ASSEMBLY

Hertz

Amps

Underwriters Laboratories, Inc.

United States and Canada

SYMBOLOGY

1. Insert 2-1/2 inch long bolt through the center hole

in rear frame, attach split lockwasher, and nuts.

Tighten securely.

2. Attach handle brace to back of rear frame with

5/8 inch long machine screws, lockwashers, and

nuts (Finger tight only).

3. Position main frame inside rear frame. Attach

with (2) 5/8 inch long machine screws, lockwash-

ers and nuts in both sides. Tighten securely.

Termékspecifikációk

Márka:	Milwaukee
Kategória:	porszívó
Modell:	8950

Szüksége van segítségre?

Ha segítségre van szüksége Milwaukee 8950, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek

Az Ön neve*

Az Ön e-mail címe*

Írja ide kérdését

Útmutatók porszívó Milwaukee

Milwaukee M18 FUEL FBPV Útmutató

29 Augusztus 2024

Milwaukee AS 30 LAC Útmutató

28 Augusztus 2024

Milwaukee M12 HV Útmutató

7 Augusztus 2024

Milwaukee M12HV Útmutató

7 Augusztus 2024

Milwaukee 10 Gal 1 Stage Wet Dry 8955 Útmutató

31 Július 2024

Milwaukee 8926 Útmutató

31 Július 2024

Milwaukee 8938-20 Útmutató

29 Július 2024

Milwaukee 0970-20 Útmutató

29 Július 2024

Milwaukee 8912 Útmutató

27 Július 2024

Milwaukee AS 300 ELCP Útmutató

26 Július 2024

Útmutatók porszívó

Legújabb útmutatók porszívó

H.Koenig UP560 Útmutató

1 Április 2025

VAX V-025 Rapide Classic Útmutató

1 Április 2025

AEG Animal 8000 AP82AF25DG Útmutató

1 Április 2025

VAX Rapide XL Útmutató

1 Április 2025

VAX CLSV-HP Útmutató

1 Április 2025

OBH Nordica X-Force 11.60 flex Útmutató

1 Április 2025

Aquavac NTP20 Professional Útmutató

31 Március 2025

Shark NV22LQ Útmutató

31 Március 2025

Electrolux z 8263 new twinclean Útmutató

31 Március 2025

Electrolux zb 254 x Útmutató

31 Március 2025