Használati útmutató Microchip dsPIC33EP256GM706

Microchip nincs kategorizálva dsPIC33EP256GM706

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Microchip dsPIC33EP256GM706 (130 oldal) a nincs kategorizálva kategóriában. Ezt az útmutatót 4 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF

Oldal 1/130

High-Speed PWM

Section 14. High-Speed PWM

HIGHLIGHTS

This section of the manual contains the following major topics:

14.1 Introduction .................................................................................................................. 14-2

14.2 Features....................................................................................................................... 14-2

14.3 Control Registers ......................................................................................................... 14-3

14.4 Architecture Overview................................................................................................ 14-24

14.5 Module Description .................................................................................................... 14-27

14.6 PWM Operating Modes.............................................................................................. 14-33

14.7 PWM Generator......................................................................................................... 14-71

14.8 PWM Trigger.............................................................................................................. 14-87

14.9 PWM Interrupts.......................................................................................................... 14-98

14.10 PWM Fault Pins ......................................................................................................... 14-99

14.11 Special Features ...................................................................................................... 14-105

14.12 PWM Output Pin Control...........................................................................................14-111

14.13 Immediate Update of PWM Duty Cycle ................................................................... 14-113

14.14 Power-Saving Modes............................................................................................... 14-114

14.15 External Control of Individual Time Base(s)............................................................. 14-114

14.16 Application Information ............................................................................................ 14-115

14.17 Register Map............................................................................................................ 14-126

14.18 Related Application Notes........................................................................................ 14-127

14.19 Revision History ....................................................................................................... 14-128

dsPIC33E/PIC24E Family Reference Manual

14.1 INTRODUCTION

This section describes the High-Speed Pulse-Width Modulator (PWM) module and its

associated operational modes. The High-Speed PWM module in the dsPIC33E/PIC24E

device family supports a wide variety of PWM modes and is ideal for power

conversion/motor control applications. Some of the common applications include:

• AC-to-DC converters

• DC-to-DC converters

• AC and DC motors: BLDC, PMSM, ACIM, SRM, etc.

• Inverters

• Battery chargers

• Digital lighting

• Uninterrupted Power Supply (UPS)

• Power Factor Correction (PFC) (e.g., Interleaved PFC and Bridgeless PFC)

14.2 FEATURES

The High-Speed PWM module consists of the following major features:

• Up to seven PWM generators, each with an individual time base

• Two PWM outputs per PWM generator

• Individual period and duty cycle for each PWM output

• Duty cycle, dead time, phase shift and frequency resolution equal to the system clock

source (TOSC)

• Independent fault and current-limit inputs for up to 14 PWM outputs

• Redundant Output mode

• Independent Output mode (this feature is not available on all devices)

• Push-Pull Output mode

• Complementary Output mode

• Center-Aligned PWM mode

• Output override control

• Special Event Trigger

• PWM capture feature

• Prescaler for input clock

• ADC triggering with PWM

• Independent PWM frequency, duty cycle and phase shift changes

• Leading-Edge Blanking (LEB) functionality

• Dead time compensation

• Output clock chopping

Note: This family reference manual section is meant to serve as a complement to device

data sheets. Depending on the device variant, this manual section may not apply to

all dsPIC33E/PIC24E devices.

Please consult the note at the beginning of the “High-Speed PWM” chapter in the

current device data sheet to check whether this document supports the device you

are using.

Device data sheets and family reference manual sections are available for

download from the Microchip Worldwide Web site at: http://www.microchip.com

Section 14. High-Speed PWM

High-Speed PWM

14.3 CONTROL REGISTERS

The following registers control the operation of the High-Speed PWM module:

•PTCON: PWM Time Base Control Register

- Enables or disables the High-Speed PWM module

- Sets the Special Event Trigger for the ADC

- Enables or disables immediate period updates

- Selects the synchronizing source for the master time base

- Specifies synchronization settings

•PTCON2: PWM Clock Divider Select Register 2

Provides the clock prescaler to the PWM master time base

•PTPER: Primary Master Time Base Period Register

Provides the PWM time period value

•STCON: PWM Secondary Master Time Base Control Registe (1)

- Enables or disables immediate period updates based on the secondary master time base

- Selects the synchronization source for the secondary master time base

- Specifies the synchronization setting for secondary master time base control

• STCON2: PWM Secondary Clock Divider Select Register 2(1)

Provides the clock prescaler to the PWM secondary master time base

•STPER: Secondary Master Time Base Period Register(1)

Provides the secondary master time base period value

•MDC: PWM Master Duty Cycle Register

Provides the PWM master duty cycle value

•SEVTCMP: PWM Special Event Compare Register

Provides the compare value that is used to trigger the ADC module

•SSEVTCMP: PWM Secondary Special Event Compare Register(1)

Provides the compare value that is used to trigger the ADC module based on the

secondary master time base

•CHOP: PWM Chop Clock Generator Register

- Provides the chop clock frequency

- Enables or disables the chop clock generator

•PWMKEY: PWM Unlock Register(1)

Writes the unlock sequence to allow writes to the IOCONx and FCLCONx registers

•PWMCONx: PWM Control Register

- Enables or disables fault interrupt, current-limit interrupt and primary trigger interrupt

- Provides the interrupt status for fault interrupt, current-limit interrupt and primary trigger

interrupt

- Selects the type of time base (master time base or independent time base)

- Selects the type of duty cycle (master duty cycle or independent duty cycle)

- Controls Dead Time mode

- Enables or disables Center-Aligned mode

- Controls the external PWM Reset operation

- Enables or disables immediate updates of the duty cycle, phase offset, independent time

base period

•IOCONx: PWM I/O Control Register

- Enables or disables PWM pin control feature (PWM control or GPIO)

- Controls fault/current limit override values

- Enables PWMxH and PWMxL pin swapping

- Controls the PWMxH and PWMxL output polarity

- Controls the PWMxH and PWMxL output if any of the following modes is selected:

• Complementary mode

• Push-Pull mode

• True Independent mode

Note: Not all registers are available on all devices. Refer to the “High-Speed PWM”

chapter in the specific device data sheet for availability.

dsPIC33E/PIC24E Family Reference Manual

•FCLCONx: PWM Fault Current-Limit Control Register

- Selects the current-limit control signal source

- Selects the current-limit polarity

- Enables or disables Current-Limit mode

- Selects the fault control signal source

- Configures the fault polarity

- Enables or disables Fault mode

•PDCx: PWM Generator Duty Cycle Register(1)

- Provides the duty cycle value for the PWMxH and PWMxL outputs, if master time base is

selected

- Provides the duty cycle value for the PWMxH output, if independent time base is selected

•PHASEx: PWM Primary Phase Shift Register

- Provides the phase shift value for the PWMxH and PWMxL output, if master time base is

selected

- Provides the independent time base period for the PWMxH output, if independent time

base is selected

•SDCx: PWM Secondary Duty Cycle Register(1,2)

Provides the duty cycle value for the PWMxL output, if independent time base is selected

•SPHASEx: PWM Secondary Phase Shift Register(1,2,3)

- Provides the phase shift for the PWMxL output, if the master time base is selected

- Provides the independent time base period value for the PWMxL output, if the independent

time base is selected

•DTRx: PWM Dead Time Register

- Provides the dead time value for the PWMxH output, if positive dead time is selected

- Provides the dead time value for the PWMxL output, if negative dead time is selected

•ALTDTRx: PWM Alternate Dead Time Register

- Provides the dead time value for the PWMxL output, if positive dead time is selected

- Provides the dead time value for the PWMxH output, if negative dead time is selected

•TRIGx: PWM Primary Trigger Compare Value Register

Provides the compare value to generate the primary PWM trigger

•TRGCONx: PWM Trigger Control Register

- Enables the PWMx trigger postscaler start event

- Specifies the number of PWM cycles to skip before generating the first trigger

•LEBCONx: Leading-Edge Blanking Control Register

- Selects the rising or falling edge of the PWM output for LEB

- Enables or disables LEB for fault and current-limit inputs

•LEBDLYx: Leading-Edge Blanking Delay Register

Provides leading-edge blanking delay for the fault and current-limit inputs

•PWMCAPx: Primary PWM Time Base Capture Register

Provides the captured independent time base value when a leading edge is detected on

the current-limit input, and when LEB processing on the current-limit input signal is

completed

•AUXCONx: PWM Auxiliary Control Register

- Selects PWM state blank and chop clock sources

- Selects PWMxH and PWMxL output chopping functionality

Section 14. High-Speed PWM

High-Speed PWM

R/W-0 U-0 R/W-0 HS/HC-0 R/W-0 R/W-0 R/W-0 R/W-0

PTEN — PTSIDL SESTAT SEIEN EIPU(1) SYNCPOL(1) SYNCOEN(1)

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

SYNCEN(1) SYNCSRC<2:0>(1) SEVTPS<3:0>(1)

bit 7 bit 0

Legend: HC = Cleared in Hardware HS = Set in Hardware

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15 PTEN: PWM Module Enable bit

1 = PWM module is enabled

0 = PWM module is disabled

bit 14 Unimplemented: Read as ‘0’

bit 13 PTSIDL: PWM Time Base Stop in Idle Mode bit

1 = PWM time base halts in CPU Idle mode

0 = PWM time base runs in CPU Idle mode

bit 12 SESTAT: Special Event Interrupt Status bit

1 = Special Event Interrupt is pending

0 = Special Event Interrupt is not pending

bit 11 SEIEN: Special Event Interrupt Enable bit

1 = Special Event Interrupt is enabled

0 = Special Event Interrupt is disabled

bit 10 EIPU: Enable Immediate Period Updates bit(1)

1 = Active Period register is updated immediately

0 = Active Period register updates occur on PWM cycle boundaries

bit 9 SYNCPOL: Synchronize Input and Output Polarity bit

(1)

1 = SYNCIx/SYNCO polarity is inverted (active-low)

0 = SYNCIx/SYNCO is active-high

bit 8 SYNCOEN: Primary Time Base Sync Enable bit(1)

1 = SYNCO output is enabled

0 = SYNCO output is disabled

bit 7 SYNCEN: External Time Base Synchronization Enable bit(1)

1 = External synchronization of primary time base is enabled

0 = External synchronization of primary time base is disabled

bit 6-4 SYNCSRC<2:0>: Synchronous Source Selection bits(1)

These bits select the SYNCIx or PTGOx input as the synchronous source. Refer to the “High-Speed

PWM” chapter in the specific device data sheet for availability.

bit 3-0 SEVTPS<3:0>: PWM Special Event Trigger Output Postscaler Select bits

(1)

1111 = 1:16 postscaler generates Special Event trigger at every 16th compare match event

•

0001 = 1:2 postscaler generates Special Event trigger at every second compare match event

0000 = 1:1 postscaler generates Special Event trigger at every compare match event

Note 1: These bits should be changed only when PTEN = 0. In addition, when using the SYNCIx feature, the user

application must program the period register with a value that is slightly larger than the expected period of

the external synchronization input signal.

Section 14. High-Speed PWM

High-Speed PWM

U-0 U-0 U-0 HS/HC-0 R/W-0 R/W-0 R/W-0 R/W-0

— — — SESTAT SEIEN EIPU(2) SYNCPOL SYNCOEN

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

SYNCEN SYNCSRC<2:0> SEVTPS<3:0>

bit 7 bit 0

Legend: HC = Cleared in Hardware HS = Set in Hardware

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-13 Unimplemented: Read as ‘0’

bit 12 SESTAT: Special Event Interrupt Status bit

1 = Secondary Special Event Interrupt is pending

0 = Secondary Special Event Interrupt is not pending

bit 11 SEIEN: Special Event Interrupt Enable bit

1 = Secondary Special Event Interrupt is enabled

0 = Secondary Special Event Interrupt is disabled

bit 10 EIPU: Enable Immediate Period Updates bit(2)

1 = Active Secondary Period register is updated immediately

0 = Active Secondary Period register updates occur on PWM cycle boundaries

bit 9 SYNCPOL: Synchronize Input and Output Polarity bit

1 = SYNCO2 output is active-low

0 = SYNCO2 output is active-high

bit 8 SYNCOEN: Secondary Master Time Base Sync Enable bit

1 = SYNCO2 output is enabled

0 = SYNCO2 output is disabled

bit 7 SYNCEN: External Secondary Master Time Base Synchronization Enable bit

1 = External synchronization of secondary time base is enabled

0 = External synchronization of secondary time base is disabled

bit 6-4 SYNCSRC<2:0>: Secondary Time Base Sync Source Selection bits

These bits select the SYNCIx or PTGOx input as the synchronous source. Refer to the “High-Speed

PWM” chapter in the specific device data sheet for availability.

bit 3-0 SEVTPS<3:0>: PWM Secondary Special Event Trigger Output Postscaler Select bits

1111 = 1:16 Postscale

•

0001 = 1:2 Postscale

0000 = 1:1 Postscale

Note 1: This register is not available on all devices. Refer to the “High-Speed PWM” chapter of the specific

device data sheet for availability.

2: This bit only applies to the secondary master time base period.

dsPIC33E/PIC24E Family Reference Manual

(1)

U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0

— — — — — — — —

bit 15 bit 8

U-0 U-0 U-0 U-0 U-0 R/W-0 R/W-0 R/W-0

— — — — — PCLKDIV<2:0>(2)

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-3 Unimplemented: Read as ‘0’

bit 2-0 PCLKDIV<2:0>: PWM Input Clock Prescaler (Divider) Select bits(2)

111 = Reserved

110 = Divide by 64

101 = Divide by 32

100 = Divide by 16

011 = Divide by 8

010 = Divide by 4

001 = Divide by 2

000 = Divide by 1, maximum PWM timing resolution (power-on default)

Note 1: This register is not available on all devices. Refer to the “High-Speed PWM” chapter of the specific

device data sheet for availability.

2: These bits should be changed only when PTEN = 0. Changing the clock selection during operation will

yield unpredictable results.

Section 14. High-Speed PWM

High-Speed PWM

(1)

R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1

STPER<15:8>

bit 15 bit 8

R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1

STPER<7:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 STPER<15:0>: Secondary Master Time Base Period Value bits

Note 1: This register is not available on all devices. Refer to the “High-Speed PWM” chapter of the specific

device data sheet for availability.

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

MDC<15:8>

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

MDC<7:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 MDC<15:0>: Master PWM Duty Cycle Value bits

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

SEVTCMP<15:8>

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

SEVTCMP<7:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 SEVTCMP<15:0>: Special Event Compare Count Value bits

Section 14. High-Speed PWM

High-Speed PWM

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

PWMKEY<15:8>

bit 15 bit 8

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

PWMKEY<7:0>

bit 7 bit 0

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

bit 15-0 PWMKEY<15:0>: PWM Unlock bits

If the PWMLOCK Configuration bit is asserted (PWMLOCK = 1), the IOCONx and FCLCONx registers

are writable only after the proper sequence is written to the PWMKEY register. If the PWMLOCK

Configuration bit is deasserted (PWMLOCK = 0), the IOCONx and FCLCONx registers are writable at

all times. Refer to 14.5.3 “Write Protection” for further details of the unlock sequence.

Note 1: This register is implemented only in devices where the PWMLOCK Configuration bit is present in the

FOSCSEL Configuration register.

Section 14. High-Speed PWM

High-Speed PWM

bit 7-6 DTC<1:0>: Dead Time Control bits

11 = Dead Time Compensation mode enabled

10 = Dead time function is disabled

01 = Negative dead time actively applied for Complementary Output mode(6)

00 = Positive dead time actively applied for all output modes

bit 5 DTCP: Dead Time Compensation Polarity bit(5)

1 = If DTCMPx pin = 0, PWMxL is shortened, and PWMxH is lengthened

If DTCMPx pin = 1, PWMxH is shortened, and PWMxL is lengthened

0 = If DTCMPx pin = 0, PWMxH is shortened, and PWMxL is lengthened

If DTCMPx pin = 1, PWMxL is shortened, and PWMxH is lengthened

bit 4 Unimplemented: Read as ‘0’

bit 3 MTBS: Master Time Base Select bit

1 = PWM generator uses the secondary master time base for synchronization and the clock source

for the PWM generation logic (if secondary time base is available)

0 = PWM generator uses the primary master time base for synchronization and the clock source for

the PWM generation logic

bit 2 CAM: Center-Aligned Mode Enable bit(2,3)

1 = Center-Aligned mode is enabled

0 = Edge-Aligned mode is enabled

bit 1 External PWM Reset Control bitXPRES: (4)

1 = Current-limit source resets primary local time base for this PWM generator if it is in Independent

Time Base mode

0 = External pins do not affect PWM time base

bit 0 IUE: Immediate Update Enable bit(3)

1 = Updates to the active MDC/PDCx/SDCx/DTRx/ALTDTRx/PHASEx/SPHASEx registers are

immediate

0 = Updates to the active MDC/PDCx/SDCx/DTRx/ALTDTRx/PHASEx/SPHASEx registers are

synchronized to the PWM time base

Note 1: Software must clear the interrupt status here, and in the corresponding IFS bit in the Interrupt Controller.

2: The Independent Time Base mode (ITB = 1 0) must be enabled to use Center-Aligned mode. If ITB = , the

CAM bit is ignored.

3: These bits should not be changed after the PWM is enabled (PTEN = 1).

4: To operate in External Period Reset mode, the ITB bit must be set to ‘ ’ and the CLMOD bit in the 1

FCLCONx register must be set to ‘0’.

5: For DTCP to be effective, DTC<1:0> must be set to ‘11’; otherwise, DTCP is ignored.

6: Negative dead time is only implemented for Edge-Aligned mode (CAM = 0).

Termékspecifikációk

Márka:	Microchip
Kategória:	nincs kategorizálva
Modell:	dsPIC33EP256GM706

Szüksége van segítségre?

Ha segítségre van szüksége Microchip dsPIC33EP256GM706, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek

Az Ön neve*

Az Ön e-mail címe*

Írja ide kérdését

Útmutatók nincs kategorizálva Microchip

Microchip AT89C51AC2 Útmutató

15 Január 2025

Microchip AT91SAM7S32 Útmutató

15 Január 2025

Microchip AT91SAM7SE32 Útmutató

15 Január 2025

Microchip AT89LS52 Útmutató

15 Január 2025

Microchip AT91SAM7S512 Útmutató

15 Január 2025

Microchip AT97SC3205T Útmutató

15 Január 2025

Microchip AT91SAM7SE512 Útmutató

15 Január 2025

Microchip AT91SAM9CN11 Útmutató

15 Január 2025

Microchip ATECC608A-TFLXTLS Útmutató

15 Január 2025

Microchip ATA8215 Útmutató

15 Január 2025

Útmutatók nincs kategorizálva

Legújabb útmutatók nincs kategorizálva

MOZA SR-P Útmutató

10 Április 2025

Soundstream VRN-64HBL Útmutató

10 Április 2025

Panasonic Lumix DMW-AC11 Útmutató

10 Április 2025

Planet PWR-240-48 Útmutató

9 Április 2025

CaterChef 445001 Útmutató

9 Április 2025

IFM E40581 Útmutató

9 Április 2025

Livn Bolt Útmutató

9 Április 2025

Livn Beats Útmutató

9 Április 2025

Alpine DP2-40C-BC Útmutató

9 Április 2025

IFM O3R252 Útmutató

9 Április 2025