Használati útmutató Microchip dsPIC33CK256MC503 (131 oldal)

HRPWM with Fine Edge

Placement

dsPIC33/PIC24 Family Reference Manual

Introduction

Note: This family reference manual section is meant to serve as a complement to device data sheets. Depending on

the device variant, this manual section may not apply to all dsPIC33 devices. Please consult the note at the

beginning of the chapter in the specific device data sheet to check whether this document supports the device you

are using.

Device data sheets and family reference manual sections are available for download from the Microchip Worldwide

Website at: www.microchip.com.

This document describes the features and use of the High-Resolution Pulse-Width Modulated (PWM) with Fine Edge

Placement. This flexible module provides features to support many types of Motor Control (MC) and Power Control

(PC) applications, including:

• AC-to-DC Converters

• DC-to-DC Converters

• AC and DC Motor Control: Brushed DC, BLDC, PMSM, ACIM, SRM, Stepper, etc.

• Inverters

• Battery Chargers

• Digital Lighting

• Power Factor Correction (PFC)

High-Level Features

• Up to Eight Independent PWM Generators, each with Dual Outputs

• Operating modes:

– Independent Edge PWM mode

– Variable Phase PWM mode

– Independent Edge PWM mode, Dual Output

– Center-Aligned PWM mode

– Double Update Center-Aligned PWM mode

– Dual Edge Center-Aligned PWM mode

• Output modes:

– Complementary

– Independent

– Push-Pull

• Dead-Time Generator

• Dead-Time Compensation

• Leading-Edge Blanking (LEB)

• Output Override for Fault Handling

• Flexible Period/Duty Cycle Updating Options

• PWM Control Inputs (PCI) for PWM Pin Overrides and External PWM Synchronization

• Advanced Triggering Options

• Combinatorial Logic Output

• PWM Event Outputs

HRPWM with Fine Edge Placement

Table of Contents

Introduction.....................................................................................................................................................1

High-Level Features....................................................................................................................................... 1

1. Registers................................................................................................................................................. 5

2. Register Maps......................................................................................................................................... 6

2.1. Common Functions Register Map................................................................................................7

2.2. PWM Generator Register Map................................................................................................... 21

3. Architecture Overview...........................................................................................................................51

4. Operation.............................................................................................................................................. 54

4.1. PWM Clocking............................................................................................................................54

4.2. PWM Generator (PG) Features..................................................................................................59

4.3. Common Features......................................................................................................................95

4.4. Lock and Write Restrictions......................................................................................................100

5. Application Examples..........................................................................................................................105

5.1. Six-Step Commutation of Three-Phase BLDC Motor...............................................................105

5.2. Three-Phase Sinusoidal Control of PMSM/ACIM Motors.........................................................114

5.3. Simple Complementary PWM Output.......................................................................................117

5.4. Cycle-by-Cycle Current Limit Mode..........................................................................................118

5.5. External Period Reset Mode.................................................................................................... 120

6. Interrupts............................................................................................................................................. 123

7. Operation in Power-Saving Modes..................................................................................................... 124

7.1. Operation in Sleep Mode..........................................................................................................124

7.2. Operation in Idle Mode............................................................................................................. 124

8. Related Application Notes...................................................................................................................125

9. Revision History.................................................................................................................................. 126

9.1. Revision A (August 2017).........................................................................................................126

9.2. Revision B (February 2018)..................................................................................................... 126

9.3. Revision C (February 2019)..................................................................................................... 126

9.4. Revision D (December 2020)................................................................................................... 126

The Microchip Website...............................................................................................................................128

Product Change Notification Service..........................................................................................................128

Customer Support...................................................................................................................................... 128

Microchip Devices Code Protection Feature..............................................................................................128

Legal Notice............................................................................................................................................... 129

Trademarks................................................................................................................................................ 129

Quality Management System..................................................................................................................... 130

HRPWM with Fine Edge Placement

Worldwide Sales and Service.....................................................................................................................131

HRPWM with Fine Edge Placement

1. Registers

There are two categories of Special Function Registers (SFRs) used to control the operation of the PWM module:

• Common, shared by all PWM Generators

• PWM Generator-specific

An ‘x’ in the register name denotes an instance of a PWM Generator.

A ‘y’ in the register name denotes an instance of a common function.

The LOCK bit in the PCLKCON register may be set in software to block writes to certain registers and bits. See 4.2

PWM Generator (PG) Features for more information. Writes to certain data and control registers are not safe at

certain times of a PWM cycle or when the module is enabled.

HRPWM with Fine Edge Placement

Registers

2. Register Maps

Section provides a brief summary of the related common High-Resolution2.1 Common Functions Register Map

PWM with Fine Edge Placement registers. Section provides a brief summary of2.2 PWM Generator Register Map

the PWM Generator registers. The corresponding registers appear after the summaries, followed by a detailed

description of each register.

HRPWM with Fine Edge Placement

Register Maps

2.1 Common Functions Register Map

Note: The number of LOGCONy and PWMEVTy registers are device-dependent. Refer to the device data sheet for

availability.

Name Bit Pos. 7 6 5 4 3 2 1 0

PCLKCON 7:0 DIVSEL[1:0] MCLKSEL[1:0]

15:8 HRRDY HRERR LOCK

FSCL 7:0 FSCL[7:0]

15:8 FSCL[15:8]

FSMINPER 7:0 FSMINPER[7:0]

15:8 FSMINPER[15:8]

MPHASE 7:0 MPHASE[7:0]

15:8 MPHASE[15:8]

MDC 7:0 MDC[7:0]

15:8 MDC[15:8]

MPER 7:0 MPER[7:0]

15:8 MPER[15:8]

LFSR 7:0 LFSR[7:0]

15:8 LFSR[14:8]

CMBTRIGL 7:0 CTA8EN CTA7EN CTA6EN CTA5EN CTA4EN CTA3EN CTA2EN CTA1EN

15:8

CMBTRIGH 7:0 CTB8EN CTB7EN CTB6EN CTB5EN CTB4EN CTB3EN CTB2EN CTB1EN

15:8

LOGCONy 7:0 S1yPOL S2yPOL PWMLFy[1:0] PWMLFyD[2:0]

15:8 PWMS1y[3:0] PWMS2y[3:0]

PWMEVTy 7:0 EVTySEL[3:0] EVTyPGS[2:0]

15:8 EVTyOEN EVTyPOL EVTySTRD EVTySYNC

HRPWM with Fine Edge Placement

Register Maps

2.1.2 Frequency Scale Register

Name: FSCL

Bit 15 14 13 12 11 10 9 8

FSCL[15:8]

Access R/W R/W R/W R/W R/W R/W R/W R/W

Reset 0 0 0 0 0 0 0 0

Bit 7 6 5 4 3 2 1 0

FSCL[7:0]

Access R/W R/W R/W R/W R/W R/W R/W R/W

Reset 0 0 0 0 0 0 0 0

Bits 15:0 – FSCL[15:0] Frequency Scale Register

The value in this register is added to the frequency scaling accumulator at each pwm_master_clk. When the

accumulated value exceeds the value of FSMINPER, a clock pulse is produced.

HRPWM with Fine Edge Placement

Register Maps

2.1.3 Frequency Scaling Minimum Period Register

Name: FSMINPER

Bit 15 14 13 12 11 10 9 8

FSMINPER[15:8]

Access R/W R/W R/W R/W R/W R/W R/W R/W

Reset 0 0 0 0 0 0 0 0

Bit 7 6 5 4 3 2 1 0

FSMINPER[7:0]

Access R/W R/W R/W R/W R/W R/W R/W R/W

Reset 0 0 0 0 0 0 0 0

Bits 15:0 – FSMINPER[15:0] Frequency Scaling Minimum Period Register

This register holds the minimum clock period (maximum clock frequency) that can be produced by the frequency

scaling circuit.

HRPWM with Fine Edge Placement

Register Maps

2.1.4 Master Phase Register

Name: MPHASE

Bit 15 14 13 12 11 10 9 8

MPHASE[15:8]

Access R/W R/W R/W R/W R/W R/W R/W R/W

Reset 0 0 0 0 0 0 0 0

Bit 7 6 5 4 3 2 1 0

MPHASE[7:0]

Access R/W R/W R/W R/W R/W R/W R/W R/W

Reset 0 0 0 0 0 0 0 0

Bits 15:0 – MPHASE[15:0] Master Phase Register

This register holds the phase offset value that can be shared by multiple PWM Generators.

HRPWM with Fine Edge Placement

Register Maps

2.1.6 Master Period Register

Name: MPER

Bit 15 14 13 12 11 10 9 8

MPER[15:8]

Access R/W R/W R/W R/W R/W R/W R/W R/W

Reset 0 0 0 0 0 0 0 0

Bit 7 6 5 4 3 2 1 0

MPER[7:0]

Access R/W R/W R/W R/W R/W R/W R/W R/W

Reset 0 0 0 0 0 0 0 0

Bits 15:0 – MPER[15:0] Master Period Register

This register holds the period value that can be shared by multiple PWM Generators.

Note: Period values less than 0x0020 should not be used (0x0080 in High-Resolution mode).

HRPWM with Fine Edge Placement

Register Maps

2.1.7 Linear Feedback Shift Register

Name: LFSR

Bit 15 14 13 12 11 10 9 8

LFSR[14:8]

Access R/W R/W R/W R/W R/W R/W R/W

Reset 0 0 0 0 0 0 0

Bit 7 6 5 4 3 2 1 0

LFSR[7:0]

Access R/W R/W R/W R/W R/W R/W R/W R/W

Reset 0 0 0 0 0 0 0 0

Bits 14:0 – LFSR[14:0] Linear Feedback Shift Register

A read of this register will provide a 15-bit pseudorandom value.

HRPWM with Fine Edge Placement

Register Maps

2.1.8 Combinational Trigger Register Low

Name: CMBTRIGL

Bit 15 14 13 12 11 10 9 8

Access

Reset

Bit 7 6 5 4 3 2 1 0

CTA8EN CTA7EN CTA6EN CTA5EN CTA4EN CTA3EN CTA2EN CTA1EN

Access R/W R/W R/W R/W R/W R/W R/W R/W

Reset 0 0 0 0 0 0 0 0

Bit 7 – CTA8EN Enable Trigger Output from PWM Generator #8 as Source for Combinational Trigger A

Value Description

1Enables specified trigger signal to be OR’d into the Combinatorial Trigger A signal

0Disabled

Bit 6 – CTA7EN Enable Trigger Output from PWM Generator #7 as Source for Combinational Trigger A

Value Description

1Enables specified trigger signal to be OR’d into the Combinatorial Trigger A signal

0Disabled

Bit 5 – CTA6EN Enable Trigger Output from PWM Generator #6 as Source for Combinational Trigger A

Value Description

1Enables specified trigger signal to be OR’d into the Combinatorial Trigger A signal

0Disabled

Bit 4 – CTA5EN Enable Trigger Output from PWM Generator #5 as Source for Combinational Trigger A

Value Description

1Enables specified trigger signal to be OR’d into the Combinatorial Trigger A signal

0Disabled

Bit 3 – CTA4EN Enable Trigger Output from PWM Generator #4 as Source for Combinational Trigger A

Value Description

1Enables specified trigger signal to be OR’d into the Combinatorial Trigger A signal

0Disabled

Bit 2 – CTA3EN Enable Trigger Output from PWM Generator #3 as Source for Combinational Trigger A

Value Description

1Enables specified trigger signal to be OR’d into the Combinatorial Trigger A signal

0Disabled

Bit 1 – CTA2EN Enable Trigger Output from PWM Generator #2 as Source for Combinational Trigger A

Value Description

1Enables specified trigger signal to be OR’d into the Combinatorial Trigger A signal

0Disabled

Bit 0 – CTA1EN Enable Trigger Output from PWM Generator #1 as Source for Combinational Trigger A

Value Description

1Enables specified trigger signal to be OR’d into the Combinatorial Trigger A signal

0Disabled

HRPWM with Fine Edge Placement

Register Maps

2.1.9 Combinational Trigger Register High

Name: CMBTRIGH

Bit 15 14 13 12 11 10 9 8

Access

Reset

Bit 7 6 5 4 3 2 1 0

CTB8EN CTB7EN CTB6EN CTB5EN CTB4EN CTB3EN CTB2EN CTB1EN

Access R/W R/W R/W R/W R/W R/W R/W R/W

Reset 0 0 0 0 0 0 0 0

Bit 7 – CTB8EN Enable Trigger Output from PWM Generator #8 as Source for Combinational Trigger B

Value Description

1Enables specified trigger signal to be OR’d into the Combinatorial Trigger B signal

0Disabled

Bit 6 – CTB7EN Enable Trigger Output from PWM Generator #7 as Source for Combinational Trigger B

Value Description

1Enables specified trigger signal to be OR’d into the Combinatorial Trigger B signal

0Disabled

Bit 5 – CTB6EN Enable Trigger Output from PWM Generator #6 as Source for Combinational Trigger B

Value Description

1Enables specified trigger signal to be OR’d into the Combinatorial Trigger B signal

0Disabled

Bit 4 – CTB5EN Enable Trigger Output from PWM Generator #5 as Source for Combinational Trigger B

Value Description

1Enables specified trigger signal to be OR’d into the Combinatorial Trigger B signal

0Disabled

Bit 3 – CTB4EN Enable Trigger Output from PWM Generator #4 as Source for Combinational Trigger B

Value Description

1Enables specified trigger signal to be OR’d into the Combinatorial Trigger B signal

0Disabled

Bit 2 – CTB3EN Enable Trigger Output from PWM Generator #3 as Source for Combinational Trigger B

Value Description

1Enables specified trigger signal to be OR’d into the Combinatorial Trigger B signal

0Disabled

Bit 1 – CTB2EN Enable Trigger Output from PWM Generator #2 as Source for Combinational Trigger B

Value Description

1Enables specified trigger signal to be OR’d into the Combinatorial Trigger B signal

0Disabled

Bit 0 – CTB1EN Enable Trigger Output from PWM Generator #1 as Source for Combinational Trigger B

Value Description

1Enables specified trigger signal to be OR’d into the Combinatorial Trigger B signal

0Disabled

HRPWM with Fine Edge Placement

Register Maps

2.1.10 Combinatorial PWM Logic Control Register y

Name: LOGCONy

Note: ‘y’ denotes a common instance (A-F); the number of the available combinatorial PWM logic is device-

dependent. Refer to the device data sheet for availability.

Bit 15 14 13 12 11 10 9 8

PWMS1y[3:0] PWMS2y[3:0]

Access R/W R/W R/W R/W R/W R/W R/W R/W

Reset 0 0 0 0 0 0 0 0

Bit 7 6 5 4 3 2 1 0

S1yPOL S2yPOL PWMLFy[1:0] PWMLFyD[2:0]

Access R/W R/W R/W R/W R/W R/W R/W

Reset 0 0 0 0 0 0 0

Bits 15:12 – PWMS1y[3:0] Combinatorial PWM Logic Source #1 Selection

Note: Logic function input will be connected to ‘ ’ if the PWM channel is not present.0

Value Description

1111 PWM8L

1110 PWM8H

1101 PWM7L

1100 PWM7H

1011 PWM6L

1010 PWM6H

1001 PWM5L

1000 PWM5H

0111 PWM4L

0110 PWM4H

0101 PWM3L

0100 PWM3H

0011 PWM2L

0010 PWM2H

0001 PWM1L

0000 PWM1H

Bits 11:8 – PWMS2y[3:0] Combinatorial PWM Logic Source #2 Selection

Note: Logic function input will be connected to ‘ ’ if the PWM channel is not present.0

Value Description

1111 PWM8L

1110 PWM8H

1101 PWM7L

1100 PWM7H

1011 PWM6L

1010 PWM6H

1001 PWM5L

1000 PWM5H

0111 PWM4L

0110 PWM4H

0101 PWM3L

0100 PWM3H

0011 PWM2L

0010 PWM2H

0001 PWM1L

HRPWM with Fine Edge Placement

Register Maps

Value Description

0000 PWM1H

Bit 7 – S1yPOL Combinatorial PWM Logic Source #1 Polarity

Value Description

1Input is inverted

0Input is positive logic

Bit 6 – S2yPOL Combinatorial PWM Logic Source #2 Polarity

Value Description

1Input is inverted

0Input is positive logic

Bits 5:4 – PWMLFy[1:0] Combinatorial PWM Logic Function Selection

Value Description

11 Reserved

10 PWMS1y ^ PWMS2y (XOR)

01 PWMS1y & PWMS2y (AND)

00 PWMS1y | PWMS2y (OR)

Bits 2:0 – PWMLFyD[2:0] Combinatorial PWM Logic Destination Selection

Note: Instances of y = A, C, E of LOGCONy assign logic function output to the PWMxH pin. Instances of y = B, D, F

of LOGCONy assign logic function to the PWMxL pin.

Value Description

111 Logic function is assigned to PWM8

110 Logic function is assigned to PWM7

101 Logic function is assigned to PWM6

100 Logic function is assigned to PWM5

011 Logic function is assigned to PWM4

010 Logic function is assigned to PWM3

001 Logic function is assigned to PWM2

000 No assignment, combinatorial PWM logic function is disabled

HRPWM with Fine Edge Placement

Register Maps

Bits 2:0 – EVTyPGS[2:0] PWM Event Source Selection

Note: No event will be produced if the selected PWM Generator is not present.

Value Description

111 PWM Generator #8

110 PWM Generator #7

101 PWM Generator #6

100 PWM Generator #5

011 PWM Generator #4

010 PWM Generator #3

001 PWM Generator #2

000 PWM Generator #1

HRPWM with Fine Edge Placement

Register Maps

2.2 PWM Generator Register Map

Legend: x = PWM Generator #; y = F, CL, FF or S.

Name Bit Pos. 7 6 5 4 3 2 1 0

Reserved

PGxCONL 7:0 HREN CLKSEL[1:0] MODSEL[2:0]

15:8 ON TRGCNT[2:0]

PGxCONH 7:0 Reserved TRGMOD SOCS[3:0]

15:8 MDCSEL MPERSEL MPHSEL MSTEN UPDMOD[2:0]

PGxSTAT 7:0 TRSET TRCLR CAP UPDATE UPDREQ STEER CAHALF TRIG

15:8 SEVT FLTEVT CLEVT FFEVT SACT FLTACT CLACT FFACT

PGxIOCONL 7:0 FLTDAT[1:0] CLDAT[1:0] FFDAT[1:0] DBDAT[1:0]

15:8 CLMOD SWAP OVRENH OVRENL OVRDAT[1:0] OSYNC[1:0]

PGxIOCONH 7:0 PMOD[1:0] PENH PENL POLH POLL

15:8 CAPSRC[2:0] DTCMPSEL

PGxEVTL 7:0 UPDTRG[1:0] PGTRGSEL[2:0]

15:8 ADTR1PS[4:0] ADTR1EN3 ADTR1EN2 ADTR1EN1

PGxEVTH 7:0 ADTR2EN3 ADTR2EN2 ADTR2EN1 ADTR1OFS[4:0]

15:8 FLTIEN CLIEN FFIEN SIEN IEVTSEL[1:0]

PGxyPCIL 7:0 SWTERM PSYNC PPS PSS[4:0]

15:8 TSYNCDIS TERM[2:0] AQPS AQSS[2:0]

PGxyPCIH 7:0 SWPCI SWPCIM[1:0] LATMOD TQPS TQSS[2:0]

15:8 BPEN BPSEL[2:0] ACP[2:0]

Reserved

PGxLEBL 7:0 LEB[10:6] [2:0]

15:8 LEB[18:11]

PGxLEBH 7:0 PHR PHF PLR PLF

15:8 PWMPCI[2:0]

PGxPHASE 7:0 PGxPHASE[7:0]

15:8 PGxPHASE[15:8]

Reserved

PGxDC 7:0 PGxDC[7:0]

15:8 PGxDC[15:8]

PGxDCA 7:0 PGxDCA[7:0]

15:8

PGxPER 7:0 PGxPER[7:0]

15:8 PGxPER[15:8]

PGxTRIGA 7:0 PGxTRIGA[7:0]

15:8 PGxTRIGA[15:8]

PGxTRIGB 7:0 PGxTRIGB[7:0]

15:8 PGxTRIGB[15:8]

PGxTRIGC 7:0 PGxTRIGC[7:0]

15:8 PGxTRIGC[15:8]

PGxDTL 7:0 DTL[7:0]

15:8 DTL[13:8]

PGxDTH 7:0 DTH[7:0]

15:8 DTH[13:8]

PGxCAP 7:0 PGxCAP[6:0]

15:8 PGxCAP[14:7]

HRPWM with Fine Edge Placement

Register Maps

2.2.1 PWM Generator x Control Register Low

Name: PGxCONL

Bit 15 14 13 12 11 10 9 8

ON TRGCNT[2:0]

Access R/W R/W R/W R/W

Reset 0 0 0 0

Bit 7 6 5 4 3 2 1 0

HREN CLKSEL[1:0] MODSEL[2:0]

Access R/W R/W R/W R/W R/W R/W

Reset 0 0 0 0 0 0

Bit 15 – ON PWM Generator x Enable

Value Description

1PWM Generator is enabled

0PWM Generator is not enabled

Bits 10:8 – TRGCNT[2:0] PWM Generator x Trigger Count Select

Value Description

111 PWM Generator produces 8 PWM cycles after triggered

110 PWM Generator produces 7 PWM cycles after triggered

101 PWM Generator produces 6 PWM cycles after triggered

100 PWM Generator produces 5 PWM cycles after triggered

011 PWM Generator produces 4 PWM cycles after triggered

010 PWM Generator produces 3 PWM cycles after triggered

001 PWM Generator produces 2 PWM cycles after triggered

000 PWM Generator produces 1 PWM cycle after triggered

Bit 7 – HREN PWM Generator x High-Resolution Enable

Note: This bit is not present on all devices. Refer to the device-specific data sheet for availability. When High-

Resolution mode is not available, this bit will read as ‘ ’.0

Value Description

1PWM Generator x operates in High-Resolution mode

0PWM Generator x operates in Standard Resolution mode

Bits 4:3 – CLKSEL[1:0] Clock Selection(1)

Notes:

1. Do not change the CLKSEL[1:0] bits while ON (PGxCONL[15]) = .1

2. The PWM Generator time base operates from the frequency scaling circuit clock, effectively scaling the duty

cycle and period of the PWM Generator output.

3. This clock source should not be used when HREN (PGxCONL[7]) = .1

Value Description

11 PWM Generator uses the master clock scaled by the frequency scaling circuit

(2,3)

10 PWM Generator uses the master clock divided by the clock divider circuit

(2)

01 PWM Generator uses the master clock selected by the MCLKSEL[1:0] (PCLKCON[1:0]) control bits

00 No clock selected, PWM Generator is in the lowest power state (default)

Bits 2:0 – MODSEL[2:0] PWM Generator x Mode Selection

Value Description

111 Dual Edge Center-Aligned PWM mode (interrupt/register update twice per cycle)

110 Dual Edge Center-Aligned PWM mode (interrupt/register update once per cycle)

101 Double Update Center-Aligned PWM mode

HRPWM with Fine Edge Placement

Register Maps

Value Description

100 Center-Aligned PWM mode

011 Reserved

010 Independent Edge PWM mode, dual output

001 Variable Phase PWM mode

000 Independent Edge PWM mode

HRPWM with Fine Edge Placement

Register Maps

Value Description

1111 TRIG bit or PCI Sync function only (no hardware trigger source is selected)

1110 - 0101 Reserved

0100 Trigger output selected by PG4 or PG8 [2:0] bits (PGxEVTL[2:0])PGTRGSEL

0011 Trigger output selected by PG3 or PG7 [2:0] bits (PGxEVTL[2:0])PGTRGSEL

0010 Trigger output selected by PG2 or PG6 [2:0] bits (PGxEVTL[2:0])PGTRGSEL

0001 Trigger output selected by PG1 or PG5 [2:0] bits (PGxEVTL[2:0])PGTRGSEL

0000 Local EOC – PWM Generator is self-triggered

HRPWM with Fine Edge Placement

Register Maps

2.2.3 PWM Generator x Status Register

Name: PGxSTAT

Legend: C = Clearable bit; HS = Hardware Settable bit

Bit 15 14 13 12 11 10 9 8

SEVT FLTEVT CLEVT FFEVT SACT FLTACT CLACT FFACT

Access HS/C HS/C HS/C HS/C R R R R

Reset 0 0 0 0 0 0 0 0

Bit 7 6 5 4 3 2 1 0

TRSET TRCLR CAP UPDATE UPDREQ STEER CAHALF TRIG

Access W W R/HS R W R R R

Reset 0 0 0 0 0 0 0 0

Bit 15 – SEVT PCI Sync Event

Value Description

1A PCI Sync event has occurred (rising edge on PCI Sync output or PCI Sync output is high when

module is enabled)

0No PCI Sync event has occurred

Bit 14 – FLTEVT PCI Fault Active Status

Value Description

1A Fault event has occurred (rising edge on PCI Fault output or PCI Fault output is high when module is

enabled)

0No Fault event has occurred

Bit 13 – CLEVT PCI Current Limit Status

Value Description

1A PCI current limit event has occurred (rising edge on PCI current limit output or PCI current limit

output is high when module is enabled)

0No PCI current limit event has occurred

Bit 12 – FFEVT PCI Feed-Forward Active Status

Value Description

1A PCI feed-forward event has occurred (the rising edge on the PCI feed-forward output or PCI feed-

forward output is high when module is enabled)

0No PCI feed-forward event has occurred

Bit 11 – SACT PCI Sync Status

Value Description

1PCI Sync output is active

0PCI Sync output is inactive

Bit 10 – FLTACT PCI Fault Active Status

Value Description

1PCI Fault output is active

0PCI Fault output is inactive

Bit 9 – CLACT PCI Current Limit Status

Value Description

1PCI current limit output is active

0PCI current limit output is inactive

Bit 8 – FFACT PCI Feed-Forward Active Status

HRPWM with Fine Edge Placement

Register Maps

Value Description

1PCI feed-forward output is active

0PCI feed-forward output is inactive

Bit 7 – TRSET PWM Generator Software Trigger Set

User software writes a ‘ ’ to this bit location to trigger a PWM Generator cycle. The bit location always reads as ‘ ’.1 0

The TRIG bit will indicate ‘ ’ when the PWM Generator is triggered.1

Bit 6 – TRCLR PWM Generator Software Trigger Clear

User software writes a ‘ ’ to this bit location to stop a PWM Generator cycle. The bit location always reads as ‘ ’. The1 0

TRIG bit will indicate ‘ ’ when the PWM Generator is not triggered.0

Bit 5 – CAP Capture Status

Value Description

1PWM Generator time base value has been captured in PGxCAP

0No capture has occurred

Bit 4 – UPDATE PWM Data Register Update Status/Control

Value Description

1PWM Data register update is pending – user Data registers are not writable

0No PWM Data register update is pending

Bit 3 – UPDREQ PWM Data Register Update Request

User software writes a ‘ ’ to this bit location to request a PWM Data register update. The bit location always reads as1

‘ ’. The UPDATE status bit will indicate a ‘ ’ when an update is pending.0 1

Bit 2 – STEER Output Steering Status (Push-Pull Output mode only)

Value Description

1PWM Generator is in 2nd cycle of Push-Pull mode

0PWM Generator is in 1st cycle of Push-Pull mode

Bit 1 – CAHALF Half Cycle Status (Center-Aligned modes only)

Value Description

1PWM Generator is in 2nd half of time base cycle

0PWM Generator is in 1st half of time base cycle

Bit 0 – TRIG Trigger Status

Value Description

1PWM Generator is triggered and PWM cycle is in progress

0No PWM cycle is in progress

HRPWM with Fine Edge Placement

Register Maps

2.2.4 PWM Generator x I/O Control Register Low

Name: PGxIOCONL

Bit 15 14 13 12 11 10 9 8

CLMOD SWAP OVRENH OVRENL OVRDAT[1:0] OSYNC[1:0]

Access R/W R/W R/W R/W R/W R/W R/W R/W

Reset 0 0 0 0 0 0 0 0

Bit 7 6 5 4 3 2 1 0

FLTDAT[1:0] CLDAT[1:0] FFDAT[1:0] DBDAT[1:0]

Access R/W R/W R/W R/W R/W R/W R/W R/W

Reset 0 0 0 0 0 0 0 0

Bit 15 – CLMOD Current Limit Mode Select

Value Description

1If PCI current limit is active, then the PWMxH and PWMxL output signals are inverted (bit flipping), and

the CLDAT[1:0] bits are not used

0If PCI current limit is active, then the CLDAT[1:0] bits define the PWM output levels

Bit 14 – SWAP Swap PWM Signals to PWMxH and PWMxL Device Pins

Value Description

1The PWMxH signal is connected to the PWMxL pin and the PWMxL signal is connected to the PWMxH

0PWMxH/L signals are mapped to their respective pins

Bit 13 – OVRENH User Override Enable for PWMxH Pin

Value Description

1OVRDAT[1] provides data for output on the PWMxH pin

0PWM Generator provides data for the PWMxH pin

Bit 12 – OVRENL User Override Enable for PWMxL Pin

Value Description

1OVRDAT[0] provides data for output on the PWMxL pin

0PWM Generator provides data for the PWMxL pin

Bits 11:10 – OVRDAT[1:0] Data for PWMxH/PWMxL Pins if Override is Enabled

Description

If OVRENH = , then OVRDAT[1] provides data for PWMxH.1

If OVRENL = , then OVRDAT[0] provides data for PWMxL.1

Bits 9:8 – OSYNC[1:0] User Output Override Synchronization Control

Value Description

11 Reserved

10 User output overrides via the SWAP, OVRENL/H and OVRDAT[1:0] bits occur when specified by the

UPDMOD[2:0] bits in the PGxCONH register

01 User output overrides via the SWAP, OVRENL/H and OVRDAT[1:0] bits occur immediately (as soon as

possible)

00 User output overrides via the SWAP, OVRENL/H and OVRDAT[1:0] bits are synchronized to the local

PWM time base (next start of cycle)

Bits 7:6 – FLTDAT[1:0] Data for PWMxH/PWMxL Pins if FLT Event is Active

Description

If Fault is active, then FLTDAT[1] provides data for PWMxH.

If Fault is active, then FLTDAT[0] provides data for PWMxL.

HRPWM with Fine Edge Placement

Register Maps

Bits 5:4 – CLDAT[1:0] Data for PWMxH/PWMxL Pins if CLMT Event is Active

Description

If current limit is active, then CLDAT[1] provides data for PWMxH.

If current limit is active, then CLDAT[0] provides data for PWMxL.

Bits 3:2 – FFDAT[1:0] Data for PWMxH/PWMxL Pins if Feed-Forward Event is Active

Description

If feed-forward is active, then FFDAT[1] provides data for PWMxH.

If feed-forward is active, then FFDAT[0] provides data for PWMxL.

Bits 1:0 – DBDAT[1:0] Data for PWMxH/PWMxL Pins if Debug Mode is Active

Description

If Debug mode is active and PTFRZ = , then DBDAT[1] provides data for PWMxH.1

If Debug mode is active and PTFRZ = , then DBDAT[0] provides data for PWMxL.1

HRPWM with Fine Edge Placement

Register Maps

2.2.5 PWM Generator x I/O Control Register High

Name: PGxIOCONH

Bit 15 14 13 12 11 10 9 8

CAPSRC[2:0] DTCMPSEL

Access R/W R/W R/W R/W

Reset 0 0 0 0

Bit 7 6 5 4 3 2 1 0

PMOD[1:0] PENH PENL POLH POLL

Access R/W R/W R/W R/W R/W R/W

Reset 0 0 0 0 0 0

Bits 14:12 – CAPSRC[2:0] Time Base Capture Source Selection

Note: A capture may be initiated in software at any time by writing a ‘ ’ to PGxCAP[0].1

Value Description

111 Reserved

110 Reserved

101 Reserved

100 Capture time base value at assertion of selected PCI Fault signal

011 Capture time base value at assertion of selected PCI current limit signal

010 Capture time base value at assertion of selected PCI feed-forward signal

001 Capture time base value at assertion of selected PCI Sync signal

000 No hardware source selected for time base capture – software only

Bit 8 – DTCMPSEL Dead-Time Compensation Select

Value Description

1Dead-time compensation is controlled by PCI feed-forward limit logic

0Dead-time compensation is controlled by PCI Sync logic

Bits 5:4 – PMOD[1:0] PWM Generator Output Mode Selection

Value Description

11 Reserved

10 PWM Generator outputs operate in Push-Pull mode

01 PWM Generator outputs operate in Independent mode

00 PWM Generator outputs operate in Complementary mode

Bit 3 – PENH PWMxH Output Port Enable

Value Description

1PWM Generator controls the PWMxH output pin

0PWM Generator does not control the PWMxH output pin

Bit 2 – PENL PWMxL Output Port Enable

Value Description

1PWM Generator controls the PWMxL output pin

0PWM Generator does not control the PWMxL output pin

Bit 1 – POLH PWMxH Output Polarity

Value Description

1Output pin is active-low

0Output pin is active-high

Bit 0 – POLL PWMxL Output Polarity

HRPWM with Fine Edge Placement

Register Maps

Value Description

1Output pin is active-low

0Output pin is active-high

HRPWM with Fine Edge Placement

Register Maps

2.2.6 PWM Generator x Event Register Low

Name: PGxEVTL

Bit 15 14 13 12 11 10 9 8

ADTR1PS[4:0] ADTR1EN3 ADTR1EN2 ADTR1EN1

Access R/W R/W R/W R/W R/W R/W R/W R/W

Reset 0 0 0 0 0 0 0 0

Bit 7 6 5 4 3 2 1 0

UPDTRG[1:0] PGTRGSEL[2:0]

Access R/W R/W R/W R/W R/W

Reset 0 0 0 0 0

Bits 15:11 – ADTR1PS[4:0] ADC Trigger 1 Postscaler Selection

Value Description

11111 1:32

. . . . . .

00010 1:3

00001 1:2

00000 1:1

Bit 10 – ADTR1EN3 ADC Trigger 1 Source is PGxTRIGC Compare Event Enable

Value Description

1PGxTRIGC register compare event is enabled as trigger source for ADC Trigger 1

0PGxTRIGC register compare event is disabled as trigger source for ADC Trigger 1

Bit 9 – ADTR1EN2 ADC Trigger 1 Source is PGxTRIGB Compare Event Enable

Value Description

1PGxTRIGB register compare event is enabled as trigger source for ADC Trigger 1

0PGxTRIGB register compare event is disabled as trigger source for ADC Trigger 1

Bit 8 – ADTR1EN1 ADC Trigger 1 Source is PGxTRIGA Compare Event Enable

Value Description

1PGxTRIGA register compare event is enabled as trigger source for ADC Trigger 1

0PGxTRIGA register compare event is disabled as trigger source for ADC Trigger 1

Bits 4:3 – UPDTRG[1:0] Update Trigger Select

Value Description

11 A write of the PGxTRIGA register automatically sets the UPDREQ bit

10 A write of the PGxPHASE register automatically sets the UPDREQ bit

01 A write of the PGxDC register automatically sets the UPDREQ bit

00 User must set the bit (PGxSTAT[3]) manuallyUPDREQ

Bits 2:0 – PGTRGSEL[2:0] PWM Generator Trigger Output Selection

Note: These events are derived from the internal PWM Generator time base comparison events.

Value Description

111 Reserved

110 Reserved

101 Reserved

100 Reserved

011 PGxTRIGC compare event is the PWM Generator trigger

010 PGxTRIGB compare event is the PWM Generator trigger

001 PGxTRIGA compare event is the PWM Generator trigger

000 EOC event is the PWM Generator trigger

HRPWM with Fine Edge Placement

Register Maps

2.2.7 PWM Generator x Event Register High

Name: PGxEVTH

Bit 15 14 13 12 11 10 9 8

FLTIEN CLIEN FFIEN SIEN IEVTSEL[1:0]

Access R/W R/W R/W R/W R/W R/W

Reset 0 0 0 0 0 0

Bit 7 6 5 4 3 2 1 0

ADTR2EN3 ADTR2EN2 ADTR2EN1 ADTR1OFS[4:0]

Access R/W R/W R/W R/W R/W R/W R/W R/W

Reset 0 0 0 0 0 0 0 0

Bit 15 – FLTIEN PCI Fault Interrupt Enable

Note: An interrupt is only generated on the rising edge of the PCI Fault active signal.

Value Description

1Fault interrupt is enabled

0Fault interrupt is disabled

Bit 14 – CLIEN PCI Current Limit Interrupt Enable

Note: An interrupt is only generated on the rising edge of the PCI current limit active signal.

Value Description

1Current limit interrupt is enabled

0Current limit interrupt is disabled

Bit 13 – FFIEN PCI Feed-Forward Interrupt Enable

Note: An interrupt is only generated on the rising edge of the PCI feed-forward active signal.

Value Description

1Feed-forward interrupt is enabled

0Feed-forward interrupt is disabled

Bit 12 – SIEN PCI Sync Interrupt Enable

Note: An interrupt is only generated on the rising edge of the PCI Sync active signal.

Value Description

1Sync interrupt is enabled

0Sync interrupt is disabled

Bits 9:8 – IEVTSEL[1:0] Interrupt Event Selection

Value Description

11 Time base interrupts are disabled (Sync, Fault, current limit and feed-forward events can be

independently enabled)

10 Interrupts CPU at ADC Trigger 1 event

01 Interrupts CPU at TRIGA compare event

00 Interrupts CPU at EOC

Bit 7 – ADTR2EN3 ADC Trigger 2 Source is PGxTRIGC Compare Event Enable

Value Description

1PGxTRIGC register compare event is enabled as trigger source for ADC Trigger 2

0PGxTRIGC register compare event is disabled as trigger source for ADC Trigger 2

Bit 6 – ADTR2EN2 ADC Trigger 2 Source is PGxTRIGB Compare Event Enable

Value Description

1PGxTRIGB register compare event is enabled as trigger source for ADC Trigger 2

HRPWM with Fine Edge Placement

Register Maps

Value Description

01 SWPCI bit is assigned to acceptance qualifier logic

00 SWPCI bit is assigned to PCI acceptance logic

Bit 4 – LATMOD PCI SR Latch Mode

Value Description

1SR latch is Reset-dominant in Latched Acceptance modes

0SR latch is set-dominant in Latched Acceptance modes

Bit 3 – TQPS Termination Qualifier Polarity Select

Value Description

1Inverted

0Not inverted

Bits 2:0 – TQSS[2:0] Termination Qualifier Source Selection

Note:

1. Polarity control bit, TQPS, has no effect on these selections.

Value Description

111 SWPCI control bit only (qualifier forced to ‘ ’)1(1)

110 Selects PCI Source #9

101 Selects PCI Source #8

100 Selects PCI Source #1 (PWM Generator output selected by the [2:0] bits)PWMPCI

011 PWM Generator is triggered

010 LEB is active

001 Duty cycle is active (base PWM Generator signal)

000 No termination qualifier used (qualifier forced to ‘ ’)1(1)

HRPWM with Fine Edge Placement

Register Maps

2.2.13 PWM Generator x Duty Cycle Register

Name: PGxDC

Bit 15 14 13 12 11 10 9 8

PGxDC[15:8]

Access R/W R/W R/W R/W R/W R/W R/W R/W

Reset 0 0 0 0 0 0 0 0

Bit 7 6 5 4 3 2 1 0

PGxDC[7:0]

Access R/W R/W R/W R/W R/W R/W R/W R/W

Reset 0 0 0 0 0 0 0 0

Bits 15:0 – PGxDC[15:0] PWM Generator x Duty Cycle Register

Note: Duty cycle values less than 0x0008 should not be used (0x0020 in High-Resolution mode).

HRPWM with Fine Edge Placement

Register Maps

Márka:	Microchip
Kategória:	nincs kategorizálva
Modell:	dsPIC33CK256MC503

Használati útmutató Microchip dsPIC33CK256MC503

Termékspecifikációk

Szüksége van segítségre?

Útmutatók nincs kategorizálva Microchip

Útmutatók nincs kategorizálva

Legújabb útmutatók nincs kategorizálva