Használati útmutató Metra 99-7882B

Metra Autós készlet 99-7882B

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Metra 99-7882B (8 oldal) a Autós készlet kategóriában. Ezt az útmutatót 10 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF

Oldal 1/8

REV. 11/14/2017 INST99-7882B

CAUTION!

Metra recommends disconnecting the negative bat

tery terminal before beginning any installation, unless the vehicle

manufacturer recommends against so. Please check with your local

Dealership for more information. All accessories, switches, climate

controls panels, and especially air bag indicator lights must be con

nected before reconnecting the battery or cycling the ignition. Also,

do not remove the factory radio with the key in the on position, or the

vehicle running. It would be best to remove the key from the ignition

and then wait a few seconds before removing the factory radio.

Installation instructions for part 99-7882B U.S. PATENT # D728,554

• ISO DIN radio provision with pocket

Note: This kit will not retain the i-MID display

• A) Radio trim panel • B) Radio brackets • C) Pocket • D) (3) metal panel clips • E) (3) plastic panel clips

• F) (4) #8 x 3/8” Phillips truss-head screws • G) (13) #8 x 3/8” Phillips pan-head screws

• H) (3) #4 x 3/8” Phillips truss-head screws • I) (2) #8 x 1/2” Phillips pan-head screws

KIT FEATURES

KIT COMPONENTS

WIRING & ANTENNA CONNECTIONS (sold separately)

Wiring Harness: • Please visit metraonline.com for options

Antenna Adapter: • 40-HD11

• Panel removal tool • Phillips screwdriver • 8mm socket wrench

TOOLS REQUIRED

A B C D E

Dash Disassembly ..................................................2

Kit Preparation ........................................................3

Kit Assembly

– ISO DIN radio provision with pocket 3 ......................

Table of Contents

99-7882B

Open the pocket door below the

radio, remove (2) Phillips screws

exposed, and then remove the

pocket. (Figure A)

Remove (2) Phillips screws from the

bottom edge of the radio. (Figure B)

3. Remove (2) 8mm screws facing

up from inside the pocket cavity.

(Figure C)

4. Unsnap and remove the climate/

radio panel assembly. (Figure D)

5. Remove the components from the

climate/radio panel to be reused in

kit assembly. (Figure E)

a. Remove (4) screws from the

climate control panel.

b. Remove (2) screws from the

factory hazard button.

c. Remove (3) screws from the

factory vent.

d. Remove (3) screws from the

lower trim panel.

Continue to kit preparation

Dash Disassembly

(Figure E)

(Figure A)

(Figure B)

(Figure C)

(Figure D)

Step 5 a

Step 5 b

Step 5 c

Step 5 d

99-7882B

Kit Preparation Kit Assembly

(Figure A)

(Figure B)

Secure the factory components removed in dash disassembly to the . Except for the radio panel

(3) screws to secure the lower trim panel, either the factory screws or the (9) #8 x 3/8” Phillips

pan-head screws supplied with the kit may be used. For the lower trim panel use the (3)

#4 x 3/8” Phillips truss-head screws supplied with the kit to secure it to the panel. (Figure A)

2. Attach the (3) metal and (3) plastic panel clips to the . The factory metal radio panel

clips may be used in place of the metal clips, but not the plastic clips. (Figure A)

Continue to kit assembly

ISO DIN radio provision with pocket

Secure the to the pocket radio brackets

with the (4) #8 x 3/8” Phillips pan-head

screws supplied with the kit. (Figure A)

2. Remove the metal DIN sleeve and

trim ring from the aftermarket radio.

Slide the radio between the bracket/

pocket assembly

and secure it with the

screws supplied with the radio. (Figure B)

4. Secure the completed assembly to

the with the (4) #8 radio trim panel

X 3/8” Phillips truss-head screws

supplied with the kit. (Figure C)

Locate the factory wiring harness and

antenna connector in the dash and

complete all necessary connections

to the radio. Metra recommends

using the proper mating adapter from

Metra and/or AXXESS. Re-connect the

negative battery terminal and test the

radio for proper operation.

Reassemble the dash in reverse order

of disassembly using the (2) #8 x 1/2”

Phillips pan-head screws supplied

with the kit for the lower radio mounts.

Metal clip locations

Plastic clip

location

Plastic clip

locations

Termékspecifikációk

Márka:	Metra
Kategória:	Autós készlet
Modell:	99-7882B

Szüksége van segítségre?

Ha segítségre van szüksége Metra 99-7882B, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek

Az Ön neve*

Az Ön e-mail címe*

Írja ide kérdését

Útmutatók Autós készlet Metra

Metra 99-8270HG Útmutató

3 Április 2025

Metra 99-8722B Útmutató

3 Április 2025

Metra 99-7802CH Útmutató

3 Április 2025

Metra 99-8214TG Útmutató

3 Április 2025

Metra 99-4000 Útmutató

1 Április 2025

Metra 95-7883HG Útmutató

29 December 2024

Metra AX-ADCT4 Útmutató

29 December 2024

Metra 99-7345B Útmutató

29 December 2024

Metra 99-7339B Útmutató

29 December 2024

Metra OESWC-7552H Útmutató

29 December 2024

Útmutatók Autós készlet

Legújabb útmutatók Autós készlet

ZZ-2 IC-SYM Útmutató

2 Április 2025

Nokia HF-33W Útmutató

16 Január 2025

Renegade REN10KIT Útmutató

31 December 2025

Scosche HA1714B Útmutató

29 December 2024

HTC Car Kit Útmutató

16 December 2024

Pioneer 12.301232-04 Útmutató

6 Október 2024

Livoo TEC602 Útmutató

2 Október 2024

Parrot Minikit Chic Útmutató

29 Szeptember 2024

Nedis DTCTCO20WT Útmutató

22 Szeptember 2024

Bury UNI Útmutató

21 Szeptember 2024