Használati útmutató Metra 95-7628BHG

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Metra 95-7628BHG (4 oldal) a nincs kategorizálva kategóriában. Ezt az útmutatót 6 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Oldal 1/4
METRA. The World’s best kits.metraonline.com © COPYRIGHT 2015 METRA ELECTRONICS CORPORATION
REV. 8/13/2015 INST95-7628BHG
CAUTION: Metra recommends disconnecting the negative battery
terminal before beginning any installation, unless the vehicle
manufacturer recommends against so. Please check with your
local Dealership for more information. All accessories, switches,
climate controls panels, and especially air bag indicator lights
must be connected before reconnecting the battery or cycling
the ignition. Also, do not remove the factory radio with the key
in the on position, or the vehicle running. It would be best to
remove the key from the ignition and then wait a few seconds
before removing the factory radio.
Installation instructions for part 95-7628BHG
A) Radio housing trim panel • B) Radio brackets
20;*64765,5;:
>0905.(5;,55(*655,*;065: (sold separately)
Wiring Harness: • 70-7552
Antenna Adapter: 40-NI12
Panel removal tool
Phillips screwdriver
;663:9,8<09,+
Nissan Murano 2015-up
95-7628BHG
A B
Dash Disassembly ................................................. 2
Kit Assembly
ISO DDIN radio provision ...................................... 3
Table of Contents
ISO DDIN radio provision
Painted to match factory finish
20;-,(;<9,:
95-7628BHG
2
Dash Disassembly
1. Slide down the shifter beauty ring
under the shift knob. (Figure A)
2. Remove the clip from the shift knob
and remove the knob. (Figure A)
3. Starting from the rear, lift and unclip
the console shifter trim panel.
(Figure B)
4. Remove the lower climate control
trim panel and remove. (Figure C)
5. Unscrew (2) Phillips screws securing
the radio/climate control trim.
(Figure D)
6. Remove the radio/climate trim.
(Figure E)
7. Remove (2) Phillips screws securing
the climate control assembly below
the radio and then remove. (Figure F)
8. Remove (2) Phillips screws securing
the vent/hazard trim panel above the
radio and then remove. (Figure F)
9. Remove (4) Phillips screws (2
above and 2 below) from the radio
assembly, then unplug and remove
the radio. (Figure G)
10. Remove the climate control module
from the radio bracket assembly and
set aside for kit assembly.
Continue to kit assembly
(Figure A) (Figure E)
(Figure B)
(Figure C)
(Figure D)
(Figure F)
(Figure G)
95-7628BHG
3
(Figure A) (Figure B)
Kit Assembly
ISO DDIN radio provision
1. Attach the radio brackets to the radio
using the screws supplied with the
radio. (Figure A)
2. Attach the climate control module
below the completed assembly using
the factory hardware. (Figure B)
3. Locate the factory wiring harness
and antenna connector in the
dash, and complete all necessary
connections to the radio and climate
controls. Metra recommends using
the proper mating adapter from
Metra and/or AXXESS. Re-connect
the negative battery terminal and
test the radio for proper operation.
4. Reassemble the dash in reverse
order of disassembly, using the
95-7628BHG radio housing
trim panel.

Termékspecifikációk

Márka: Metra
Kategória: nincs kategorizálva
Modell: 95-7628BHG

Szüksége van segítségre?

Ha segítségre van szüksége Metra 95-7628BHG, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek




Útmutatók nincs kategorizálva Metra

Metra

Metra 82-8602 Útmutató

14 Január 2025
Metra

Metra 99-8274 Útmutató

14 Január 2025
Metra

Metra 95-7642 Útmutató

2 Január 2025
Metra

Metra 71-017C Útmutató

26 Szeptember 2024
Metra

Metra AXSP-HK Útmutató

26 Szeptember 2024
Metra

Metra 109-TO7 Útmutató

25 Szeptember 2024
Metra

Metra 95-8273B Útmutató

7 Szeptember 2024
Metra

Metra 95-7822 Útmutató

7 Szeptember 2024

Útmutatók nincs kategorizálva

Legújabb útmutatók nincs kategorizálva