Használati útmutató Metra 95-3027

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Metra 95-3027 (4 oldal) a nincs kategorizálva kategóriában. Ezt az útmutatót 7 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Oldal 1/4
CAUTION!
All accessories, switches, climate
controls panels, and especially air bag indicator
lights must be connected before cycling the
ignition. Also, do not remove the factory radio
with the key in the on position, or while the
vehicle is running.
Metra. The World’s Best Kits.®MetraOnline.com © COPYRIGHT 2018 METRA ELECTRONICS CORPORATION REV. 7/31/18 INST95-3027
I N S TA L L AT I O N I N S T R U C T I O N S
95-3027
KIT FEATURES
ISO DDIN radio provision
APPLICATIONS
Chevrolet S-10 Blazer 1998-2002*
Chevrolet S-10 Pickup 1998-2002*
GMC Sonoma 1998-2002*
Isuzu Hombre 1998-2000
* Only for early 2002 models denoted by a DIN and a half size radio
KIT COMPONENTS
• A) Radio trim panel • B) Radio brackets
TOOLS REQUIRED
• Panel removal tool • Phillips screwdriver
• 9/32” socket wrench • cutting tool • Scribe tool
TABLE OF CONTENTS
Dash Disassembly ..................................................2
Kit Preparation .......................................................3
Kit Assembly ..........................................................3
WIRING & ANTENNA CONNECTIONS
(sold separately)
Wiring Harness: 70-1858
Antenna Adapter: 40-GM10
A B
GM Small trucks/SUV’s 1998-2002
1.800.221.0932
|
MetraOnline.com
2
1. Remove (2) 9/32” screws securing the
driver’s side knee bolster to the dash.
(Figure A)
2. Slightly pull down on the knee bolster
to expose the 9/32” screws securing the
base of the dashboard trim panel, then
remove the screws. (Figure A)
3. Remove (1) Phillips screw in the
instrument cluster.
4. Unclip and remove the dashboard trim
panel, using caution not to damage the
hazard switch while removing the panel.
5. Remove (2) 9/32” screws securing the
radio. Slide the radio out, then unplug
and remove the radio.
Continue to Kit Preparation
(Figure A)
DASH DISASSEMBLY KIT PREPARATION
1. Place the
radio trim panel
over the
factory dashboard trim panel. (Figure A)
2. Using a scribe tool, score the area in the
radio section to be cut. (Figure B)
3. Remove the
radio trim panel
, then cut
the scored area with a cutting tool.
Continued on the next page
(Figure A)
(Figure B)
Remove shaded area
Mark here
REV. 7/31/2018 INST95-3027 3
KIT ASSEMBLY
(Figure A)
KIT PREPARATION (CONT.)
4. Slide the
radio trim panel
into the
bottom opening of the factory
dashboard trim panel, then clip in the
top portion. Note, if the center bar of
the radio trim panel is bowed, file the
opening of the factory dashboard trim
panel to fit better. (Figure C)
5. Cut the sub-dash to allow room for the
radio assembly. (Figure D)
Continue to Kit Assembly (Figure C)
(Figure D)
1. Secure the
radio brackets
to the radio
using the screws supplied with the
radio. (Figure A)
2. Locate the factory wiring harness and
antenna connector in the dash and
complete all necessary connections to
the radio. Metra recommends using
the proper mating adapter from Metra
and/or Axxess. Test the radio for proper
operation.
3. Secure the radio assembly to the dash
using the factory screws.
4. Reassemble the dash in reverse
order of disassembly to complete the
installation.
Remove
shaded area

Termékspecifikációk

Márka: Metra
Kategória: nincs kategorizálva
Modell: 95-3027

Szüksége van segítségre?

Ha segítségre van szüksége Metra 95-3027, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek




Útmutatók nincs kategorizálva Metra

Útmutatók nincs kategorizálva

Legújabb útmutatók nincs kategorizálva

MOZA

MOZA SR-P Útmutató

10 Április 2025
CaterChef

CaterChef 445001 Útmutató

9 Április 2025
IFM

IFM E40581 Útmutató

9 Április 2025
Livn

Livn Bolt Útmutató

9 Április 2025
Livn

Livn Beats Útmutató

9 Április 2025
IFM

IFM O3R252 Útmutató

9 Április 2025