Használati útmutató Maytag MFI2269VEQ

Maytag hűtőszekrény MFI2269VEQ

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Maytag MFI2269VEQ (96 oldal) a hűtőszekrény kategóriában. Ezt az útmutatót 2 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/96
Ice2OTM French Door Bottom Freezer
Use & Care Guide
R
Form No. B/02/06 Part No. 12828140 www.maytag.com ©2006 Maytag Appliances Sales Co. Litho USA
Table of Contents
Important Safety
Instructions .................................... 1-2
Quick Reference Guide ....................3
Installation ..................................... 4-9
Using the Controls................... 10-11
Ice And Water ............................12-13
Water Filter .................................14-15
Fresh Food Features ................ 16-18
Freezer Features ............................. 18
Food Storage Tips .................... 19-21
Care and Cleaning................... 22-25
Oper .......................... 26ating Sounds
Troubleshooting........................ 27-30
Warr 31anty & Service ........................
Guide d’utilisation et
d’entretien........................................ 32
Guía de uso y cuidado .................. 64
®
1
Important Safety Instructions
WARNING – Hazards or unsafe practices which
COULD result in severe personal injury or death.
WARNING
DANGER – Immediate hazards which WILL result
in severe personal injury or death.
DANGER
CAUTION – Hazards or unsafe practices which COULD
result in minor personal injury or property damage.
CAUTION
What You Need to Know About
Safety Instructions
Warning and Important Safety Instructions appearing in
this guide are not meant to cover all possible
conditions and situations that may occur. Common
sense, caution and care must be exercised when
installing, maintaining or operating appliance.
Always contact the manufacturer about problems or
conditions you do not understand.
Recognize Safety Symbols, Words,
Labels
This appliance is equipped with a three-prong
grounded plug for your protection against possible
electrical shock hazards. It must be plugged into a
properly grounded wall receptacle. Where a standard
two-prong wall receptacle is encountered, it is the
personal responsibility and obligation of the customer
to have it replaced with a properly grounded three-
prong wall receptacle. Do not, under any
circumstances, cut or remove the third (ground)
prong from the power cord. Do not use an adapter
plug.
Power supply cord with
three-prong grounded plug
Properly
grounded type
wall receptacle
To reduce risk of injury or death, follow basic
precautions, including the following:
Important: Child entrapment and suffocation are
not problems of the past. Junked or abandoned
refrigerators are still dangerous – even if they sit out
for “just a few days.” If you are getting rid of your old
refrigerator, please follow the instructions below to
help prevent accidents.
Before you throw away your old
refrigerator or freezer:
• Take off the doors.
• Leave the shelves in place so
children may not easily climb
inside.
• Cut off power cord plug.
DANGER
Installer: Please leave this guide with this appliance.
Consumer: Please read and keep this Use and
Care Guide for future reference; it provides the
proper use and maintenance information.
Keep sales receipt and/or canceled check as proof
of purchase.
Call: 1-800-688-9900 USA
1-800-688-2002 Canada
Have complete model and serial number
identification of your refrigerator. This is located on a
data plate inside the fresh food compartment, on the
upper right side. Record these numbers below for
easy access.
Model Number _______________________________
Serial Number ________________________________
Date of Purchase______________________________
In our continuing effort to improve the quality and
performance of our appliances, it may be necessary
to make changes to the appliance without revising
this guide.
To reduce risk of fire, electric shock, serious
injury or death when using your refrigerator,
follow basic precautions, including the following:
1. Read all instructions using the refrigerator.before
2. Observe all local codes and ordinances.
3. Be sure to follow grounding instructions.
4. Check with a qualified electrician if you are not
sure this appliance is properly grounded.
5. Do not ground to a gas line.
6. Do not ground to a cold-water pipe.
7. Refrigerator is designed to operate on a separate
115 volt, 15 amp., 60 cycle line.
8. Do not modify plug on power cord. If plug does
not fit wall receptacle, have proper receptacle
installed by a qualified electrician.
9. Do not use a two-prong adapter, extension cord
or power strip.
10. Do not remove warning tag from power cord.
11. Do not tamper with refrigerator controls.
12. Do not service or replace any par of refrigeratort
unless specifically recommended in Use and Care
Guide or published user-repair instructions.
Do not attempt service if instructions are not
understood or if they are beyond personal skill
level.
13. Always disconnect refrigerator from electrical
supply before attempting any service. Disconnect
power cord by grasping the plug, not the cord.
14. Install refrigerator according to Installation
Instructions. All connections for water, electrical
power and grounding must comply with local
codes and be made by licensed personnel when
required.
15. Keep your refrigerator in good condition. Bumping
or dropping refrigerator can damage refrigerator
or cause refrigerator to malfunction or leak. If
damage occurs, have refrigerator checked by
qualified service technician.
16. Have worn power cords and/or loose plugs
replaced by a qualified service technician.
17. Always read and follow manufacturer’s storage
and ideal environment instructions for items being
stored in refrigerator.
18. Your refrigerator should not be operated in the
presence of explosive fumes.
19. Children should not climb, hang or stand on any
part of the refrigerator.
20. Clean up spills or water leakage associated with
water inst allation.
2
Important Safety Instructions
SAVE THESE INSTRUCTIONS
WARNING
3
Quick Reference Guide
Quick Reference Guide
A
B
C
DEF
G
HI
J
K
Use to control the temperature in the refrigerator and freezer compartments. Temperatures
are preset at the factory at 3 8° F (3° C) in the refrigerator compartment and 0° F (-18° C) in
the freezer compar tment.
Senses light level within the room. Used with Autolight feature.
Use as a reminder to order or replace the filter.
P ss and hold the pad for re three seconds to reset lights.
Indicates a door has been left open.
To deactivate: close the door or pre ss the pad.
Use to lock all functions.
To activate: press until green light illuminates.
To deactivate: press and hold the pad for seconds until green light turns off.three
Use to select water .
Use to alert if temperatures exceed normal range. Press once to stop audible alarm.
To deactivate: press and hold pad for three seconds.
Use to select ice.
Use to activate or deactivate the light. P ress pad once twice for Auto, for Continuous or
three times to deactivate.
Use to quickly drop compartment temperatures to minimum settings.
To activate: press pad.
To deactivate: press pad again.
Use to defrost le ss frequently when you are away .
To activate once: press the pad .
To deactivate: press the pad again or open a door and the light will turn off.
A
B
C
D
E
F
G
H
I
J
K
Temperature Control
Light Sensor
Reset Filter
Door Alarm
Lock/Unlock
Water
Temp Alarm
Cube
Light
Max Cool
Vacation Mode
See pages 10-11 for more information on controls.
4
Materials Needed:
•3⁄8” hex head driver
• Carpenter’s level.
1. Remove toe grille.
• Grasp firmly and pull
outward to unclip.
2. Using hex head driver, turn
the front adjustment screws (A) on each side to
raise or lower the front of the refrigerator (see
illustration below).
3. Using the hex head driver, turn each of these
adjustment screws (B) to raise or lower the rear of
the refrigerator .
4. Using a carpenter’s level, make sure front of
refrigerator is 1⁄4” (6 mm) or approximately 1⁄2bubble
higher than back of refrigerator and that the
refrigerator is level from side to side.
5. Turn stabilizing legs (C) clockwise until firmly
against floor.
6. Turn adjustment screws (A) counterclockwise to
allow the full weight of the refrigerator to re st on
the stabilizing legs.
7. Replace the toe grille.
Installation
Your refrigerator was packed carefully for shipment.
Remove and discard shelf packaging and tape. Do not
remove the serial plate.
Location
• Do not install refrigerator near oven, radiator or other
heat source. If not possible, shield refrigerator with
cabinet material (contact a qualified contractor).
•Do not install where temperature falls below 55° F
(13° C) or rises above 110° F (43° C). Malfunction may
occur at this temperature.
•Refrigerator is designed for indoor household
application only.
Measuring the Opening
When installing your refrigerator, measure carefully.
Allow
1⁄2” space at top and 1⁄2” space behind the machine
compartment cover (located in the rear) for proper air
circulation.
Subflooring or floor coverings (i.e. carpet, tile, wood
floors, rugs) may make your opening smaller than
anticipated.
Some clearance may be gained by using the leveling
procedure under Leveling.
Important: If refrigerator is to be installed into a recess
where the top of the refrigerator is completely covered,
use distance from floor to top of hinge cap to verify
proper clearance.
Transporting Your Refrigerator
• NEVERtranspor t refrigerator on its side. If an upright
position is not possible, lay refrigerator on its back.
Allow refrigerator to sit upright for approximately 30
minutes before plugging it in to assure oil returns to
the compressor. Plugging the refrigerator in
immediately may c ause damage to internal par ts.
• Use an appliance dolly when moving refrigerator.
ALWAYS truck refrigerator from it s side or
back–NEVER from its front.
• Protect outside finish of refrigerator during transport
by wrapping cabinet in blankets or inserting padding
between the refrigerator and dolly.
• Secure refrigerator to dolly firmly with straps or
bungee cords. Thread straps through handles when
possible. Do not over-tighten. Over-tightening
restraints may dent or damage outside finish.
Leveling
To protect property and refrigerator from
damage, observe the following:
• Protect vinyl or other flooring with cardboard, rugs,
or other protective material.
•Do not use power tools when performing leveling
procedure.
CAUTION
To enhance the appearance and maintain performance,
the refrigerator should be leveled per instructions
below.
Notes:
• Complete any required water supply connection
before leveling.
• Some models only have adjustment screws (A).
C C
A B A
B
• Align the toe grille mounting clips with the lower
cabinet slots.
• Push the toe grille firmly until it snaps into place.
5
Installation
To avoid electrical shock which can cause
severe personal injury or death, observe the
following:
• Disconnect power to refrigerator before removing
doors or drawer. Connect refrigerator door wire
harness and power only after replacing doors or
drawer.
WARNING
To avoid damage to walls and flooring, protect vinyl
or other flooring with cardboard, rugs or other
protective material. Monitor water connection for 24
hours. Correct leaks if necessary.
CAUTION
Door and Drawer Removal
Some installations require door/drawer removal to
transport the refrigerator to its final location.
1. Unplug power cord from power source.
2. Remove toe grille (see page 4).
3. Remove top hinge cover
from right side refrigerator
door by removing Phillips
screw. Retain screw and
cover for later use.
4. Unscrew 5⁄16” hex head
screws from top hinge to
remove hinge and retain
all screws for later use.
Note: For refrigerators in operation, shut off water
before disconnecting water line from the door.
6. Remove top hinge cover
from left side refrigerator
door by removing Phillips
screw. Retain screw and
cover for later use.
7. Disconnect wire harness
on top left side of
refrigerator door top
hinge. Release connector
by pressing junction
point with a flat blade
screwdriver or fingernail.
8. Disconnect waterline.
Hold “tabbed” section of
waterline while rotating
the black locking collar
clockwise and slide back.
9. Unscrew 5⁄16” hex head
screws from top hinge to
remove hinge; retain for
later use.
10. Lift left side refrigerator
door, along with top hinge,
from center hinge pin.
11. Remove Phillips screws to
remove right and left hinges;
retain all screws for later
use.
12. Remove both stabilizing
brackets with 3⁄8” hex
head driver; retain
screws for later use.
Tabs
Connector
5. Lift right side
refrigerator door from
center hinge pin.
Remove door closure
from center hinge pin
on the right side and
retain for later use.
Right
side
door
closure
6
Installation
Pullout Freezer Drawer
To avoid electrical shock which can cause severe
personal injury or death, disconnect power to
refrigerator before removing doors. After replacing
doors, connect power.
WARNING
To avoid possible injury, product, or property
damage, you will need two people to perform the
following instructions. Important: Always unload
food in freezer trays before removing trays.
CAUTION
3. Remove Phillips screws from
each of the drawer slides.
Door Reinstallation
1. Install hinge assemblies:
• Install center hinges with Phillips or hex screws.
2. Place hinge side of refrigerator
door on center hinge pin.
• Install top hinge with 5⁄16” hex
head screws.
3. While holding refrigerator door upright, tighten
down top hinge with 5⁄16” hex head driver.
4. Reconnect connector.
5. Connect the waterline tubes firmly by pushing one
waterline inside the other.
6. Slide the black locking collar fully forward.
7. Hold tabbed section of
waterline.
8. Rotate black locking collar
counterclockwise locking
water lines in place. A
“click” is heard ensuring
waterlines are correctly
locked in place. The “arrow”
on the tabbed section
should align with the 2 bars
on the black locking collar.
9. Ensure the connection does not leak before
installing the upper hinge cover.
10. Replace top hinge covers.
To Remove:
1. Pull drawer open to full
extension.
2. Slide freezer bins forward and
lift straight out.
4. Lift top of drawer front to
unhook the drawer from the
slides.
5. Move drawer slides fully
forward.
6. Lift out lower drawer assembly.
Connector
Tabs
7
Notes:
• Select models have a slight
curve to the freezer handle.
• For proper installation, be sure
handle is oriented as shown.
Freezer Handle
Handles
Installation
5. Grasp the handle firmly and slide
down.
Plastic Handle
To Remove:
1. Grasp the lower part of the handle
firmly, slide up, lift and remove
from the surface.
4. Rotate the handle so that the
handle is flat against the door.
To Install:
1. Pull both rails out to
full extension.
2. While supporting
door front, hook
supports into slots
located on inside of
each slide.
Note: All four drawer bracket supports must be in
the proper slots for the drawer to function properly.
(See inset for detail.)
3. Lower door front into final position.
4. Replace and tighten Phillips screws that were
removed from the drawer
slides.
5. Install the lower assembly
by aligning hooks of lower
drawer assembly with rear
rail on freezer drawer.
6. Replace freezer bins. Align
the large square notches
on outside of the drawer
slides.
3. Ensure the large hole in the
mounting clip is positioned
down on both ends of the
handle.
Door
Stud
To Install:
1. The handles are to be oriented as
shown.
2. Align door handle clip with the
door studs.
Note: If not installed, the handle is located in the
interior of the fresh food compartment or attached
to the back of your refrigerator.
8
Connecting the Water Supply
To reduce the risk of injury or death, follow
basic precautions, including the following:
• Read all instructions installing ice maker.before
•Do not attempt installation if instructions are not
understood or if they are beyond personal skill
level.
• Observe all local codes and ordinances.
•Do not service ice maker unless specifically
recommended in Use and Care Guide or
published user-repair instructions.
• Water damage due to an improper water
connection may cause mold/mildew growth. Clean
up spills or leakage immediately!
WARNING
To avoid property damage or possible injury,
follow basic precautions, including the
following:
• Consult a plumber to connect 1⁄4”O.D. copper
tubing to household plumbing to assure
compliance with local codes and ordinances.
• Confirm water pressure to water valve is between
35 and 100 pounds per square inch, 20 pounds
per square inch without filter.
•Do not use a self-piercing, or 3⁄16” saddle valve.
Both reduce water flow and can become clogged
over time, and may cause leaks if repair is
attempted.
• Tighten nuts by hand to prevent cross threading.
Finish tightening nuts with pliers and wrenches.
Do not over-tighten.
• Wait two to three hours before placing refrigerator
into final position to check and correct any water
leaks. Recheck for leaks after 24 hours.
• Verify the copper tubing under the sleeve is
smooth and free from defects. Do not reuse an
old sleeve.
CAUTION
Installation
To Install:
1. Align door handle clips
to the studs attached to
the freezer door.
2. Ensure the large hole in
the mounting clip is
positioned to the right
on both ends of the
handle.
3. Rotate the handle so that the handle is flat against
the door.
4. Grasp the handle firmly and slide handle to the
right.
To Remove:
1. With both hands, firmly grasp the handle toward
the right side.
2. Slide toward the left, lift and remove from the
surface.
To Remove:
• Loosen set screws in
handle using 3⁄32” Allen
wrench.
• Repeat the procedure on
all screws.
To Replace:
• Align handle with the
mounting posts.
• Fully tighten all set
screws to secure handle
in place.
Metal Handle
Materials Needed:
•3⁄32” Allen wrench
• Gloves to protect hands
Note: Metal handles can scratch doors.
9
1. Create service loop with copper
tubing (minimum 2’
diameter). Avoid kinks in
the copper tubing when
bending it into a service
loop. Do not use plastic
tubing.
Installation
Cont.
Materials Needed:
•1⁄4” outer diameter flexible copper tubing
• Shut-off valve (requires a 1⁄4” hole to be drilled into
water supply line before valve attachment)
• Adjustable wrenches (2)
•1⁄4” hex nut driver
Notes:
• Use copper tubing only for installation. Plastic is
less durable and can cause damage.
• Add 8’ to tubing length needed to reach water
supply for creation of service loop.
2’ diameter
minimum
2. Remove plastic cap from water supply connection.
3. Place brass nut (A) (B)and sleeve
on copper tube end as illustrated.
Reminder: Do not use an old sleeve.
The nut and sleeve are provided in
the Use and Care packet.
A
B
4. Place end of copper
tubing into water valve
supply line.
5. Slide brass nut over
sleeve and screw nut
into supply line.
(1) Place adjustable
wrench on nut attached
to plastic waterline and
maintain position.
(2) Using second
adjustable wrench turn
the upper nut clockwise
and fully tighten while holding the lower nut in
place.
6. Pull on tubing to confirm
connection is secure. Connect
tubing to frame with water
tubing clamp (C). Slide
waterline into retainer, then
turn on water supply. Check
for leaks and correct if
necessary. Continue to
observe the water supply
connection for two to three
hours prior to moving the refrigerator to its
permanent location.
7. Monitor water connection for 24 hours. Correct
leaks, if necessary.
C
Important: Do not over-tighten. Cross threading may
occur.
Opening and Closing Your
Fresh Food Doors
Your new refrigerator is
uniquely designed with two
fresh food doors. Either door
can be opened or closed
independently of one another.
For proper usage and to
avoid possible damage,
always ensure the vertical
hinged section (on the left
fresh food door) remains
folded inward before closing
both doors. When both doors
are closed, the hinged section
automatically forms a seal between the two doors.
When the left door is opened, the vertical hinged
section automatically folds inward so that is is out of
the way.
To avoid electrical shock which can cause severe
personal injury or death, DO NOT attempt to
remove the vertical hinged section from the fresh
food section.
WARNING
To avoid possible product damage, ALWAYS verify
that the vertical hinged section is folded against
the edge of the door prior to closing.
CAUTION
Vertical
Hinged
Section
2’
Waterline
Supply
Retainer
1
2
Waterline
Supply
Retainer
12
Ice and Water
Ice and Water Dispenser
To Use Dispenser Paddle:
• Choose Water selection
from dispenser control
panel.
• Press a sturdy,
wide-mouthed container
against dispenser paddle.
• Dispenser Light will come
on while paddle is pressed.
• Release pressure on
dispenser paddle to stop
water dispensing. A small
amount of water may
continue to dispense and collect in dispenser tray.
Large spills should be wiped dry.
Note:If dispenser is active for more than five
minutes, an automatic lock out sensor will shut
down power to dispenser area. See Dispenser
Lock/Unlock for unlocking information.
Dispenser Lock/Unlock
The Dispenser Lock/Unlock affects all
keypad functions.
To Lock Dispenser:
• Press and hold the Lock/Unlock button for three
seconds. A green indicator light above the button will
illuminate when the dispenser is locked.
To Unlock Dispenser:
• Hold the button for seconds. TheLock/Unlock three
green indicator light above will go out.
Note: During initial use of water dispenser and
ice maker, there will be a one to two minute delay
while water tank fills before water dispenses or ice
is made. Discard first 10-14 glasses of water after
initially connecting refrigerator to household water
supply. Additional flushing may be required in
some households where water is of poor quality.
Water
Cube
Dispenser
Paddle
Removable Tray
Automatic Ice Maker
Connect the ice maker to the
water supply as instructed on
pages 8-9. A properly leveled
refrigerator is essential for
optimal ice maker production.
Ice Storage Bin
The ice storage bin is
located below the automatic
ice maker in the upper left
side enclosure of the fresh
food compartment.
To Remove:
• Depress the button on the
lower right of the ice
storage bin to release from the enclosure.
Continue pulling until resistance is felt. Lift up front
of ice bin and remove. Press the switch on the front
of the ice maker to turn the ice maker off.
ON/OFF
switch
that the light levels in the room are low. Setting 1 is
the darkest light level setting, setting 9 is the brightest
light level setting. Important: The Auto Light must be
activated on the ice and water dispenser control to
take advantage of this option.
Sabbath Mode (SAb)
When the Sabbath Mode is on, all control lights, interior
lights, night light, ice and water dispenser and alarm
tones will be disabled until the feature is turned off.
Press the Door Alarm pad for seconds to restorethree
the lights.
Warm Cabinet Surfaces
At times, the front of the refrigerator cabinet and the
vertical hinged section of the door may be warm to the
touch. This is a normal occurrence that helps prevent
moisture from condensing on the cabinet. This
condition will be more noticeable when the refrigerator
is first started, during hot weather and after excessive
or lengthy door openings.
Removable Tray
The removable tray at the bottom of the dispenser area
is designed to collect small spills and may be easily
removed for cleaning and emptying purposes.
Important: Removable tray does not drain. Do not
allow tray to overflow. If it does, remove tray and wipe
up overflow.
To Dispense Ice and Water:
• Select Water Cubeor ice mode by pushing button
on dispenser control panel. A green light above
button indicates mode selection.
• Press container against dispenser paddle. When
dispensing ice, hold container as close to chute as
possible to reduce spraying.
Notes:
• Dispenser light will not activate during dispensing
while in Sabbath Mode.
• If the power fails, the control will remain in
Sabbath Mode when power returns.
13
Important: Do not remove ice storage bin without
pressing ice maker switch to OFF. Removing ice
storage bin while ON could result in ice falling into the
ice storage bin enclosure, blocking the dispenser and
disabling the bin from being locked into proper
position.
To Install:
Important: Ice bin must be
locked in place for proper ice
dispensing. If necessary, turn
auger driver behind ice bin
counterclockwise to properly align
ice bin with auger driver.
• Press the switch ON to activate
ice maker. Slide bin into guide rails located on either
side of the enclosure. Push the ice bin in until
resistance is felt. Raise the front slightly and push
the ice bin completely in. An audible “click” is
heard when the ice bin is located correctly.
Operating Instructions
• Confirm ice bin is in place.
• After freezer section reaches between 0° to 2° F (-18°
to -17° C), ice maker fills with water and begins
operating. You will have a complete harvest of ice
approximately every hour.
• Allow approximately 3 to 6 hours after installation to
receive first harvest of ice.
• Discard ice created within the first 12 hours of
operation to verify system is flushed of impurities.
• Stop ice production by pressing the ON/OFF switch
located on the front of the ice maker.
• The first one or two batches will probably contain
undersized and irregular cubes because of air in the
supply line.
• When the ice cubes are ejected it is normal for
several cubes to be joined together at the ends. They
can easily be broken apart. The ice maker will
continue to make ice until the supply of ice cubes
raises the ice maker arm, shutting the ice maker off.
• Certain sounds may accompany the various cycles of
the ice maker. The motor may have a slight hum, the
cubes will rattle as they fall into an empty storage bin
and the water valve may click or “buzz” occasionally.
To avoid personal injury or property damage,
observe the following:
•Do not place fingers or hands on the automatic
ice making mechanism while the refrigerator is
plugged in. This will help protect you from possible
injury. It will also prevent interference with moving
parts of the ejector mechanism and the heating
element that releases the cubes.
• Under certain rare circumstances, ice cubes may
be discolored, usually appearing with a green-
bluish hue. The cause of this unusual discoloration
can be a combination of factors such as certain
characteristics of local waters, household
plumbing and the accumulation of copper salts in
an inactive water supply line which feeds the ice
maker. Continued consumption of such discolored
ice cubes may be injurious to health. If such
discoloration is observed, discard the ice cubes
and contact your dealer to purchase and install a
water line filter.
• Water damage due to improper water connection
may cause mold/mildew growth.
• Clean up water and ice spills to avoid personal
injury and to prevent mold/mildew growth.
•Do not dispense ice directly into thin glass, fine
china or delicate crystal.
WARNING
Ice and Water
• If the ice is not used frequently, the ice cubes will
become cloudy, shrink, stick together and taste stale.
Empty the ice storage bin periodically and wash it in
lukewarm water. Be sure to dry the bin thoroughly
before replacing it.
• Beverages and foods be placed in theshould not
ice storage bin for quick chilling. These items can
cause the ice maker to malfunction.
• Press the switch on the ice maker front to OFF when
the water supply is to be shut off for several hours.
Note: Access to the ice storage bin will be limited
with the left fresh food door opened at 90 degrees.
Move cabinet forward to enable door to open
sufficiently for ice storage bin access.
Auger Driver
14
Water Filter
Water Filter Removal and
Installation
To avoid serious illness or death, do not use
refrigerator where water is unsafe or of unknown
quality without adequate disinfection before or after
use of filter.
WARNING
After installing a new water filter, always
dispense water for two minutes before
removing the filter for any reason. Air trapped in
system may cause water and cartridge to eject.
Use caution when removing.
• The bypass cap doe not filter water. Be sure tos
have replacement cartridge available when filter
change is required.
• If water filtration system has been allowed to
freeze, replace filter cartridge.
• If system has not been used for several months, or
water has an unpleasant taste or odor, flush
system by dispensing water for two to three
minutes. If unpleasant taste or odor persists,
change filter cartridge.
CAUTION
Initial Installation
The water filter is located
in the upper right-hand
corner of the fresh food
compartment.
1. Remove blue bypass
cap and retain for later
use.
2. Remove sealing label from
end of filter and insert into
filter head.
3. Rotate gently clockwise until
filter stops. Snap filter cover
closed.
Replacing Water Filter
Important: Air trapped in system may cause water
and cartridge to eject. Always dispense water for
at least 2 minutes before removing the filter or
blue bypass cap for any reason. Use caution when
removing.
1. Turn filter until it releases fromcounterclockwise
filter head.
2. Drain water from filter into sink, and dispose in
normal household trash.
3. Wipe up excess water in filter cover and continue
with Initial Installation, steps 2 and 3.
The filter should be changed at least every 12 months.
Important: Condition of water and amount used
determines life span of water filter cartridge. If water
use is high, or if water is of poor quality, replacement
may need to take place more often.
To purchase a replacement water filter cartridge,
contact your dealer or call 1-877-232-6771 USA or
1-800-688-8408 Canada.
The dispenser feature may be used without a water
filter cartridge. If you choose this option, replace filter
with blue bypass cap.
Sta orniate of Calif
Department of Health Services
Water Treatment Device
Cer tificate Number
03 - 1583
Date Issued: September 16, 2003
Date Revised: April 22, 2004
Tr kademar /Model Designa placement Elementstion Re
UKF8001AXX750 UKF8001AXX
469006-750 46 9006
67003523-750 67003523
Manufacturer: PentaPure Inc.
The water treatment device(s) listed on this certificate have met the testing requirements
pursuant to Section 116830 of the Health and Safety Code for the following health related
contaminant's:
Microbiological contaminant's and Turbidity Inor anic/Radiolog gical contaminant's
Cysts Asbestos
Turbidity Lead
Mercury
Organic contaminant's
Atrazine
Lindane
Benzene
Carbofuran
p-dichlorobenzene
Toxaphene
Rated Service Capacity: Rated Service Flow:750 gal. 0.78 gpm
Conditions of Certification:
Do not use where water is microbiologically unsafe or with water of unknown quality, except that
systems certified for cyst reduction may be used on disinfected waters that may contain filterable
cysts.
Pull tab foward
15
Water Filter
System Specification and Performance Data Sheet
Refrigerator Water Filter Cartridge Model UKF8001AXX
Specifications
Service Flow Rate (Maximum).............................................0.78 GPM (2.9 L/min)
Rated Service Life UKF8001AXX-750 (Maximum)......750 gallons/2838 liters
Maximum Operating Temperature .....................................100° F / 38° C
Minimum Pressure Requirement........................................35 psi /241 kPA
Minimum Operating Temperature......................................33° F /1° C
Maximum Operating Pressure.............................................120 psi /827 kPA
Performance Data
1000 Apollo Road
Eagan, Minnesota 55121-2240
651.450.4913
EPA EST #35917-MN-1
100834/B
The PuriCleanTM II retractable water filtration system uses a
UKF8001AXX replacement cartridge. Timely replacement
of filter cartridge is essential for performance satisfaction
from this filtration system. Please refer to the applicable
section of your Use and Care Guide for general operation,
maintenance requirements and troubleshooting.
Suggested retail price of replacement water filter is $39.99.
This system has been tested according to ANSI/NSF 42 and
53 for reduction of the substances listed above. The
concentration of the indicated substances in water entering
the system was reduced to a concentration less than or
equal to the permissible limit for water leaving the system,
as specified in ANSI/NSF 42 and 53.
General Use Conditions
Read this Performance Data Sheet and compare the
capabilities of this unit with your actual water
treatment needs.
DO NOT use this product where water is
microbiologically unsafe or of unknown quality
without adequate disinfection before or after the
system. System certified for cyst reduction may be
used on disinfected water that may contain
filterable cysts.
USE ONLY WITH COLD WATER SUPPLY. CHECK
FOR COMPLIANCE WITH THE STATE AND LOCAL
LAWS AND REGULATIONS.
* Tested using a flow rate of 0.78 gpm; pressure of 60 psig; pH of 7.5 + 0.5; temp. of
68° + 5° F (20° + 3° C)
** Measurement in Particles /ml. Particles used were 0.5 - 1 microns
*** NTU - Nephelometric Turbidity Units
Standard No. 42: Aesthetic Effects
Taste and Odor Reduction
Chlorine Taste & Odor
Mechanical Filtration Unit
Particulate Reduction Class 1
Standard No. 53: Health Effects
Chemical Reduction Unit
Lead, Atrazine, Lindane, Benzene,
Carbofuran, p-Dichlorobenzene, Mercury
& Toxaphene Reduction
Mechanical Filtration Unit
Cyst, Turbidity and Asbestos Reduction
Tested and certified by NSF International against ANSI/NSF Standards 42 & 53
in models UKF8001AXX-750 for the reduction of:
Parameter
Chlorine
T & O
Particulate**
USEPA
MCL
—
—
—
Standard No. 42: Aesthetic Effects
Influent
Challenge Concentration
2.0 mg/ L ± 10%
—
at least 10,000 particles/ ml
Influent
Average
1.88 mg /L
—
5,700,000 #/ml
Average
<0.05136364 mg / L
—
30,583 #/ml
Maximum
0.06 mg /L
—
69,000 #/ml
Average
> 97.26%
—
99.52%
Minimum
96.84%
—
98.94%
Min. Required
Reduction
50%
—
85%
Effluent % Reduction
USEPA
MCL
1 NTU**
99.5% Reduction
99% Reduction
0.015 mg/L
0.015 mg/L
0.002 mg/L
0.002 mg/L
0.003 mg/L
0.005 mg/L
0.04 mg/L
0.075 mg/L
0.0002 mg/L
0.003 mg/L
Standard No. 53: Health Effects
Influent
Challenge Concentration
11 ± 1 NTU***
Minimum 50,000/L
107108fibers/L; fibers >10 micrometers in length
0.15 mg/L + 10%
0.15 mg/L + 10%
.00 mg/L ± 10%6
.006 mg/L ± 10%
0.009 mg/L + 10%
0.0 10%15 mg/L ±
0.08 mg/L ± 10%
.225 mg/L ± 10%
0.002 mg/L + 10%
0.015 ± 10%
Influent
Average
10.7 NTU
166,500 #/L
155 MF/L
0.153 mg/L
0.150 mg/L
0.00 mg/L6
0.006 mg/L
0.009 mg/L
0.014 mg/L
0.081 mg/L
0.208 mg/L
0.002 mg/L
0.015 mg/L
Average
0.3 NTU1
< #/L1
<1 MF/L
<.00 mg/L1
<.001 mg/L
0.0003 mg/L
0.0008 mg/L
<0.002 mg/L
0.000 mg/L6
<0.001 mg/L
<0.0005 mg/L
0.000 mg/L
<0.001 mg/L
Maximum
.049 NTU
<1 #/L
<1 MF/L
<.00 mg/L1
<.001 mg/L
0.0005 mg/L
0.0015 mg/L
0.002 mg/L
0.0011 mg/L
<0.001 mg/L
<0.0005 mg/L
<0.000 mg/L1
<0.001 mg/L
Average
97.09%
>99.99%
>99.99%
>99.35%
>99.33%
95.70%
86.22%
76.99%
95.71%
98.74%
99.76%
98.72%
92.97%
Minimum
95.20%
>99.99%
>99.99%
>99.29%
>99.29%
90.91%
75.93%
75.31%
92.14%
98.46%
99.74%
96.50%
91.67%
Min. Required
Reduction
0.5 NTU
>99.95%
99%
0.10 mg/L
0.10 mg/L
0.002 mg/L
0.002 mg/L
0.003 mg/L
0.005 mg/L
0.04 mg/L
0.075 mg/L
0.0002 mg/L
0.003 mg/L
Effluent % Reduction
Parameter
Turbidity
Cysts
Asbestos
Lead at pH 6.5
Lead at pH 8.5
Mercury at pH 6.5
Mercury at pH 8.5
Atrazine
Benzene
Carbofuran
p-Dichlorobenzene
Lindane
Toxaphene
TM
16
Fresh Food Features
Shelves
To avoid personal injury or property damage,
observe the following:
•Never attempt to adjust a shelf that is loaded with
food.
• Confirm shelf is secure before placing items on
shelf.
• Handle tempered glass shelves carefully. Shelves
may break suddenly if nicked, scratched, or
exposed to sudden temperature change.
CAUTION
Spill-CatcherTM Glass Shelves
Your refrigerator has Spill-CatcherTM glass shelves. The
shelves have a spill retainer edge which allows for
easier clean up and some are equipped with a slide
out feature. To slide out, grasp the front of the shelf
and pull forward. Push in the shelf to return to the
original position.
To Remove a Shelf:
• Slightly tilt up the front and lift up
the rear of the shelf, then pull the
shelf straight out.
To Lock the Shelf Into Another
Position:
• Tilt up the front edge of the shelf.
• Insert the hook into the desired frame openings and
let the shelf settle into place.
• Be sure the shelf is securely locked at the rear.
Latches
Slide Out
EasyGlide Shelf
EasyGlide Shelf
EasyGlide Shelf
EasyGlide Shelf
EasyGlide Shelf
TM
(style may vary)
Elevator™ Shelf (select models)
The Elevator™ Shelf is equipped with a spill-retaining
edge and the EasyGlide™ slide-out feature. It can be
adjusted up or down without unloading.
To Slide Out EasyGlide™ Shelf:
• Grasp the front of the shelf and pull forward.
• Push the shelf in to return to original position.
To Adjust the Elevator™ Shelf:
• Pull out the knob on the crank handle.
• Rotate the crank clockwise to raise the shelf, and
counterclockwise to lower the height of the shelf.
To Remove Elevator™ Shelf:
• Completely unload the shelf and pull the shelf
forward.
• Pull until the shelf stops.
• Slightly tilt up the front and pull the shelf straight
out. Continue pulling forward until the shelf is clear
of the frame.
To Replace Elevator™ Shelf:
• Align the shelf to the frame and push it all the way
back.
In ordinary use, the Elevator™ Shelf frame assembly
does NOT require removal. Though unlikely, and not
recommended, the correct removal procedure is as
follows:
To Remove Frame Assembly:
• Unload the shelf completely.
• Slide the shelf forward about 2” and manually move
the two rear latches toward the shelf center.
• While supporting the entire shelf and frame from
underneath, lift slightly and rotate the assembly
approximately 30° to allow the rear mechanism to
clear the vertical rear side rails.
• The entire assembly can then be moved forward and
clear of the refrigerator compartment.
To Reinstall Frame Assembly:
• Reverse the removal procedure. Be sure the shelf is
in a level position. When the sliding shelf is pushed
to the rear, it will reposition the rear latches to their
correct operating position.
17
Door Storage
Dairy Center
The dairy center provides
convenient door storage for
spreadable items such as butter
and margarine. This compartment
can be moved to different locations to accommodate
storage needs. To use the dairy center, raise the cover.
To Remove:
• Raise the cover, push upward and pull out.
To Install:
• Slide the dairy center in and push down until firmly
seated in the door liner.
Door Buckets
Door buckets can be moved to meet storage needs.
To Remove:
• Slide bucket up and pull straight out.
To Install:
• Slide bucket in and push down
until firmly seated in the door
liner.
Crisper Top
The crisper top serves as the lower fresh food shelf.
To Remove the Crisper Top:
• Remove crisper drawers.
• Place hand under the frame to push up the glass. Lift
glass out.
• Lift frame from fresh food liner rails.
To Install:
• Replace frame in fresh food liner rails.
• Carefully replace glass into frame.
Note: For best results, keep the crisper drawers
tightly closed.
To Remove:
• Pull drawer out to full extension. Tilt up front of
drawer and pull straight out.
To Install:
• Insert drawer into frame rails and push back into
place.
Crisper Drawers
The crisper drawers provide a higher humidity
environment for fresh fruit and vegetable storage.
Wide-N-FreshTM Drawer
The Wide-N-FreshTM drawer is a full-width drawer with
adjustable temperature control. This drawer can be
used for large party trays, deli items, beverages or
miscellaneous items and features a divider to organize
the drawer into sections if desired.
There is a
temperature
control which
adjusts the
amount of cold
air allowed into
the drawer.
The control is
located on the right side of the drawer, under
the lid.
Set the control to the higher setting to provide a
normal fresh food temperature.
Set the drawer on the lower setting when a
temperature colder than the main fresh food
compartment is desired. Use the coldest setting when
storing meats.
Notes:
• Cold air directed to the drawer can decrease fresh
food temperature. Fresh food control may need to
be adjusted.
•Do not place leafy vegetables in the drawer.
Colder temperatures could damage leafy produce.
Fresh Food Features
Controls
The crisper controls regulate the amount of humidity in
the crisper drawer. Slide the control toward the FRUIT
setting for produce with outer skins. Slide the control
toward the VEG ETABLES setting for leafy produce.
18
To Remove Divider:
• Pull drawer completely out and raise the front of the
divider to unhook it from the rear wall of the drawer,
then lift drawer out.
To Install Divider:
• Hook back of divider over rear wall of drawer and
lower into place.
Accessories
Egg Tray (style may vary)
The egg tray holds a “dozen-
plus” eggs. It can be removed
to carry to a work area or to
be washed.
Wine Trivet/Can Rack
The wine trivet/can rack accessory
fits in the Wide-N-Fresh™ drawer or
on a shelf.
Bottles or cans can be laid crosswise, or a single bottle
may be laid in the center depression.
Fresh Food Features
Temperature Controlled
Beverage Chiller
The beverage chiller keeps
beverages and other items cooler
than the rest of the fresh food
section. A cold air inlet allows air
from the freezer section to pass into
the beverage chiller. The beverage
chiller control is located on the right
wall of the fresh food compartment.
The control adjusts the amount of
cold air allowed into the beverage
chiller. For a cooler temperature in
the beverage chiller, slide the
control down.
To Remove:
• Slide bucket up and straight out.
Firmly hold each side of the
beverage chiller, lift up and
away from the door.
To Install:
• Reverse above procedure.
To Remove Drawer:
• Lift lid. Pull drawer out to full extension. Tilt up front
of drawer and pull straight out.
To Install Drawer:
• Push metal glide rails to the back of the fresh food
compartment. Place drawer onto rails and slide
drawer back until it falls into place.
Freezer Features
Note: See pages 6-7 for complete information on
lower drawer and drawer removal.
To Remove:
• Pull drawer out to full extension and lift bins out to
remove.
To Install:
• Slide bin into freezer. Make
sure the large square holes
along outer bin align with
square knobs on freezer
drawer.
Freezer Bin Freezer Bin Divider
The freezer drawer features a divider in the bin to
organize the drawer into sections if desired.
Lower Freezer Drawer
Built-In Door Organizer
The vertical organizer is located in the
fresh food section on the inside left
door. The organizer is designed to hold
six - 12oz. cans, 20oz. bottles, baby
bottles, or yogurt containers,
individually.
19
Food Storage Tips
Fresh Food Storage
• The fresh food compartment of a refrigerator should
be kept between 34°- 40° F (1°- 4° C) with an
optimum temperature of 37° F (3° C). To check the
temperature, place an appliance thermometer in a
glass of water and place in the center of the fresh
food compartment. Check after 24 hours. If the
temperature is above 40° F (4° C) adjust the controls
as explained on page 10.
• Avoid overcrowding the fresh food shelves. This
reduces the circulation of air around the food and
results in uneven cooling.
Fruits and Vegetables
• Storage in the crisper drawers traps humidity to help
preserve the fruit and vegetable quality for longer
time periods (see page 17).
• Sort fruits and vegetables before storage and use
bruised or soft items first. Discard those showing
signs of decay.
• Always wrap odorous foods such as onions and
cabbage so the odor does not transfer to other foods.
• While vegetables need a certain amount of humidity
to remain fresh, too much humidity can shorten
storage times (especially leafy vegetables). Drain
vegetable well s before storing.
• Wait to wash fresh produce until right before use.
Meat and Cheese
• Storage in Wide-N-FreshTM drawer helps preserve
quality for longer time periods.
• Raw meat and poultry should be wrapped securely
so leakage and contamination of other foods or
surfaces does not occur.
• Occasionally mold will develop on the surface of
hard cheeses (Swiss, Cheddar, Parmesan). Cut off at
least an inch around and below the moldy area. Keep
your knife or instrument out of the mold itself.
Do not try to save individual cheese slices, soft
cheese, cottage cheese, cream, sour cream or yogurt
when mold appears.
Dairy Food
• For milk and cream, store in the Temperature
Controlled Beverage Chiller which is designed to
maintain a lower temperature for optimum freshness
and life.
• Most dairy foods such as milk, yogurt, sour cream
and cottage cheese have freshness dates on their
cartons for appropriate length of storage. Store these
foods in the original carton and refrigerate
immediately after purchasing and after each use.
Frozen Food Storage
• The freezer compartment of a refrigerator should be
kept at approximately 0° F (-18° C). To check the
temperature, place an appliance thermometer
between the frozen packages and check after 24
hours. If the temperature is above 0° F (-18° C),
adjust the control as described on page 10.
• A freezer operates more efficiently when it is at least
two-thirds full.
Packaging Foods for Freezing
• To minimize dehydration and quality deterioration use
aluminum foil, freezer wrap, freezer bags or airtight
containers. Force as much air out of the packages as
possible and be sure they are tightly sealed. Trapped
air can cause the food to dry out, change color and
develop an off-flavor (freezer burn).
• Overwrap fresh meats and poultry with suitable
freezer wrap prior to freezing.
•Do not refreeze meat that has completely thawed.
Loading the Freezer
• Avoid adding too much warm food to the freezer at
one time. This overloads the freezer, slows the rate of
freezing and can raise the temperature of frozen
foods.
• Leave space between the packages so cold air can
circulate freely, allowing food to freeze as quickly as
possible.
Refer to the Food Storage Chart on pages 20 and 21 for
approximate storage times.

Termékspecifikációk

Márka: Maytag
Kategória: hűtőszekrény
Modell: MFI2269VEQ

Szüksége van segítségre?

Ha segítségre van szüksége Maytag MFI2269VEQ, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók hűtőszekrény Maytag

Maytag

Maytag MFC2062FEZ Útmutató

12 Január 2025
Maytag

Maytag MFES6030RZ Útmutató

3 Szeptember 2024
Maytag

Maytag MRSF4036PZ Útmutató

25 Augusztus 2024
Maytag

Maytag MRSF4036PB Útmutató

25 Augusztus 2024
Maytag

Maytag MRSF4036PW Útmutató

25 Augusztus 2024
Maytag

Maytag MSD2574VEM Útmutató

22 Augusztus 2024
Maytag

Maytag MBF2254HEW Útmutató

22 Augusztus 2024
Maytag

Maytag MBF2258FEZ Útmutató

22 Augusztus 2024
Maytag

Maytag MRT311FFFH Útmutató

22 Augusztus 2024
Maytag

Maytag MRT311FFFBK Útmutató

22 Augusztus 2024

Útmutatók hűtőszekrény

Legújabb útmutatók hűtőszekrény

Atag

Atag KD6122B Útmutató

1 Április 2025
Viking

Viking FRUI5242D Útmutató

1 Április 2025
Electrolux

Electrolux ERL6296XX Útmutató

31 Március 2025
Cylinda

Cylinda KF2166LFH Útmutató

31 Március 2025
Amica

Amica AR7252W Útmutató

31 Március 2025
Bosch

Bosch KGN39OCAF Útmutató

31 Március 2025
Atag

Atag KS38178A Útmutató

30 Március 2025
Summit

Summit SPRF34D7 Útmutató

30 Március 2025
Summit

Summit BAR631BK Útmutató

30 Március 2025
Daewoo

Daewoo FR 146 R Útmutató

29 Március 2025