Használati útmutató Makita GV7000C
Olvassa el alább 📖 a magyar nyelvű használati útmutatót Makita GV7000C (16 oldal) a Sander kategóriában. Ezt az útmutatót 4 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra
Oldal 1/16
I N S T R U C T I O N M A N U A L
WARNING:
For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
w w w . m a k i t a t o o l s . c o m
Electronic Disc
Sander
180 mm (7”)
MODEL GV7000C
003426
DOUBLE
INSULATION
2
SPECIFICATIONS
• Manufacturer reserves the right to change specifications without notice.
• Specifications may differ from country to country.
GENERAL SAFETY RULES USA002-2
(For All Tools)
WARNING:
Read and understand all instructions. Failure to follow all
instructions listed below, may result in electric shock, fire and/or
serious personal injury.
SAVE THESE INSTRUCTIONS
Work Area
1. Keep your work area clean and well lit.
Cluttered benches and dark areas invite acci-
dents.
2. Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases, or dust. Power
tools create sparks which may ignite the dust
or fumes.
3. Keep bystanders, children, and visitors
away while operating a power tool. Distrac-
tions can cause you to lose control.
Electrical Safety
4. Double insulated tools are equipped with
a polarized plug (one blade is wider than
the other.) This plug will fit in a polarized
outlet only one way. If the plug does not fit
fully in the outlet, reverse the plug. If it
still does not fit, contact a qualified elec-
trician to install a polarized outlet. Do not
change the plug in any way. Double insula-
tion eliminates the need for the three wire
grounded power cord and grounded power
supply system.
Model GV7000C
Abrasive disc diameter 180 mm (7”)
No load speed (RPM) 2,500 - 4,700/min.
Overall length 210 mm (8 - 1/4”)
Net weight 2.0 kg (4.4 lbs)
Spindle thread 5/8”
3
5. Avoid body contact with grounded sur-
faces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of
electric shock if your body is grounded.
6. Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
7. Do not abuse the cord. Never use the cord
to carry the tools or pull the plug from an
outlet. Keep cord away from heat, oil,
sharp edges or moving parts. Replace
damaged cords immediately. Damaged
cords increase the risk of electric shock.
8. When operating a power tool outside, use
an outdoor extension cord marked “W-A”
or “W”. These cords are rated for outdoor
use and reduce the risk of electric shock.
Personal Safety
9. Stay alert, watch what you are doing and
use common sense when operating a
power tool. Do not use tool while tired or
under the influence of drugs, alcohol, or
medication. A moment of inattention while
operating power tools may result in serious
personal injury.
10. Dress properly. Do not wear loose cloth-
ing or jewelry. Contain long hair. Keep
your hair, clothing, and gloves away from
moving parts. Loose clothes, jewelry, or long
hair can be caught in moving parts.
11. Avoid accidental starting. Be sure switch
is off before plugging in. Carrying tools with
your finger on the switch or plugging in tools
that have the switch on invites accidents.
12. Remove adjusting keys or wrenches
before turning the tool on. A wrench or a
key that is left attached to a rotating part of
the tool may result in personal injury.
13. Do not overreach. Keep proper footing
and balance at all times. Proper footing and
balance enables better control of the tool in
unexpected situations.
14. Use safety equipment. Always wear eye
protection. Dust mask, non-skid safety
shoes, hard hat, or hearing protection must
be used for appropriate conditions. Ordinary
eye or sun glasses are NOT eye protection.
Tool Use and Care
15. Use clamps or other practical way to
secure and support the workpiece to a
stable platform. Holding the work by hand or
against your body is unstable and may lead
to loss of control.
16. Do not force tool. Use the correct tool for
your application. The correct tool will do the
job better and safer at the rate for which it is
designed.
17. Do not use tool if switch does not turn it
on or off. Any tool that cannot be controlled
with the switch is dangerous and must be
repaired.
18. Disconnect the plug from the power
source before making any adjustments,
changing accessories, or storing the tool.
Such preventive safety measures reduce the
risk of starting the tool accidentally.
19. Store idle tools out of reach of children
and other untrained persons. Tools are
dangerous in the hands of untrained users.
20. Maintain tools with care. Keep cutting
tools sharp and clean. Properly maintained
tools with sharp cutting edges are less likely
to bind and are easier to control.
21. Check for misalignment or binding of
moving parts, breakage of parts, and any
other condition that may affect the tools
operation. If damaged, have the tool ser-
viced before using. Many accidents are
caused by poorly maintained tools.
22. Use only accessories that are recom-
mended by the manufacturer for your
model. Accessories that may be suitable for
one tool, may become hazardous when used
on another tool.
Termékspecifikációk
| Márka: | Makita |
| Kategória: | Sander |
| Modell: | GV7000C |
Szüksége van segítségre?
Ha segítségre van szüksége Makita GV7000C, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek
Útmutatók Sander Makita
28 Március 2025
28 Március 2025
5 Október 2024
17 Szeptember 2024
14 Szeptember 2024
13 Szeptember 2024
2 Szeptember 2024
30 Augusztus 2024
20 Augusztus 2024
13 Augusztus 2024
Útmutatók Sander
- Sander Milwaukee
- Sander Parkside
- Sander Worx
- Sander Bosch
- Sander AEG
- Sander Einhell
- Sander Ozito
- Sander Hyundai
- Sander Flex
- Sander Scheppach
- Sander Ergotools Pattfield
- Sander Mafell
- Sander Güde
- Sander Hitachi
- Sander Toolcraft
- Sander Proviel
- Sander Hilti
- Sander Black & Decker
- Sander Global
- Sander Fieldmann
- Sander PowerPlus
- Sander DEDRA
- Sander Metabo
- Sander Biltema
- Sander Bavaria
- Sander RYOBI
- Sander Proxxon
- Sander HiKOKI
- Sander Festool
- Sander McKenzie
- Sander Trotec
- Sander Bavaria By Einhell
- Sander Herkules
- Sander Porter-Cable
- Sander DeWalt
- Sander Gastroback
- Sander Stanley
- Sander Silverline
- Sander Vonroc
- Sander Arendo
- Sander TAURUS Titanium
- Sander Alpha Tools
- Sander Holzmann
- Sander Fein
- Sander Cocraft
- Sander Craftsman
- Sander Maestro
- Sander Hazet
- Sander Ferm
- Sander Far Tools
- Sander Tryton
- Sander Skil
- Sander Meec Tools
- Sander Dremel
- Sander Tacklife
- Sander Maktec
- Sander Bort
- Sander Power Craft
- Sander Topcraft
- Sander Gamma
- Sander Matrix
- Sander Kress
- Sander Duro
- Sander Varo
- Sander Max
- Sander Truper
- Sander Kinzo
- Sander Bruder Mannesmann
- Sander Meister Craft
- Sander RIDGID
- Sander Probuilder
- Sander Rupes
- Sander Batavia
- Sander Protool
- Sander Westfalia
- Sander Black Decker
- Sander Stomer
- Sander Elu
- Sander Wagner SprayTech
- Sander King Craft
- Sander Powertec
- Sander Rikon
- Sander Duro Pro
- Sander Toolson
- Sander Toledo
- Sander FIXIT
- Sander Einhell Bavaria
- Sander THUN
- Sander Prowork
- Sander Stalco
- Sander Kraftronic
Legújabb útmutatók Sander
30 Március 2025
30 Március 2025
15 Január 2025
12 Január 2025
12 Január 2025
2 Január 2025
29 December 2024
29 December 2024
29 December 2024
28 December 2024