Használati útmutató Lezyne Mini Drive XL

Lezyne Kerékpár lámpa Mini Drive XL

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Lezyne Mini Drive XL (2 oldal) a Kerékpár lámpa kategóriában. Ezt az útmutatót 6 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF

Oldal 1/2

English User Manual

READ ENTIRE MANUAL BEFORE OPERA-

TION to ensure proper use and care of

your new Lezyne LED light. Trac laws

mandang lighng vary from country to

country. Inform yourself about lighng

laws in the country of use.

Warnings

DO NOT LOOK DIRECTLY INTO LIGHT BEAM or shine into eyes of another.

DO NOT SUBMERGE UNDER WATER. Lezyne LED lights are water resistant under

normal condions, but are not waterproof. If moisture gets inside light body,

remove tailcap and air-out unl completely dry.

DO NOT ATTEMPT TO REMOVE ELECTRONICS. Doing so will void warranty.

Use only genuine Lezyne branded LIR 123A baeries. See Charging for instruc

ons on installing baery.

Lezyne USA, Inc. and Lezyne Co., Ltd. do not accept any liability for injuries or

other damages resulng from the use of this product in any circumstances.

Warranty

In U.S. and U.K., Lezyne LED Lights carry a two (2) year warranty from the

original purchase date to the original owner (proof of purchase is required).

Lezyne Baeries carry a six (6) month warranty from the original purchase date.

Lezyne warranes cover any manufacturing defects in materials or workmanship.

Issues not covered by warranty include normal wear & tear, improper installaon,

aempng to access or modify electronics, damage or failure due to accident,

misuse, abuse and/or neglect.

For warranty issues outside of the United States, contact the distributor/retailer

for your country or region directly. To nd a distributor near you, visit:

hp://lezyne.com/contact/distributors

Mounting

1. Slide clamp over handlebar with bolt hole facing forward, place top

mount on clamp, insert thumbscrew from boom.

2. Tighten thumbscrew unl snug; clamp should not rotate on handlebar.

DO NOT OVERTIGHTEN. Max Torque: 5.0 Nm

3. Slide LED light into top plate from front. CONFIRM TAB ENGAGEMENT.

To remove LED light, depress release tab; pull light forward.

NOTE: When installing on carbon surfaces, verify ghtening torque recom-

mendaon with the carbon parts manufacturer to prevent over ghtening that

can cause damage to the carbon material and/or under ghtening that can

cause lack of xing strength.

Operation

1. ON/OFF: hold buon two (2) sec.

2. Mode cycle: click buon

3. Overdrive Race Mode: hold buon ve (5) sec.

OVERDRIVE RACE MODE: With the light OFF, hold buon for ve (5) seconds,

unl light ashes. The light is now in Overdrive Race Mode where only Overdrive

and Economy outputs are selectable. The light will remain in Overdrive Race

Mode even when switched OFF. Repeat the step above to return to the normal

mode set.

THERMAL PROTECTION: If the operang temperature of the light is too high,

the light automacally lowers the lumen output.

MAINTENANCE: For water resistance, ensure that tailcap, buon, and USB

protecve cover are fully installed before every use. Keep tailcap threads

clean and apply small amount of thick, mulpurpose grease to tailcap threads

if necessary.

Run Times and Modes

MINI DRIVE:

FL1 STANDARD

OVERDRIVE ENDURO BLAST ECONOMY FLASH 1

250

LUMENS

100

LUMENS

200

LUMENS

100

LUMENS