Használati útmutató Keurig K575

Keurig Kávéfőző K575

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Keurig K575 (2 oldal) a Kávéfőző kategóriában. Ezt az útmutatót 5 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF

Oldal 1/2

Caring For Your Brewer

Regular cleaning keeps your brewer running smoothly. Always be sure to turn off and unplug your brewer before cleaning.

Brewer Exterior

Keep your Keurig® brewer looking its best by cleaning the exterior

from time to time. Just clean with a damp, soapy, lint-free, non-

abrasive cloth. Never immerse the brewer in water or other liquids.

Pod Holder

Lift the handle. Push up while

grabbing the sides of the pod

holder assembly. Pull away

from brewer. Pull out the pod

holder assembly and base. Press

the release buttons on both

sides of the pod holder assembly.

Seperate the pod holder from

the housing. Clean the pod

holder (1), housing (2), and base

(3) with a damp, soapy, lint-free,

non-abrasive cloth and rinse

thoroughly. After all pieces are

cleaned, reassemble the pod

holder assembly by inserting

the pod holder back into the

housing. Place the base, then

the pod holder assembly into the

brew head. Lower the handle.

CAUTION: Sharp needles. Do not put

fingers in chamber.

Cleaning the Exit Needle

If a clog arises in the exit needle,

push the lever of the pod holder

to reveal the exit needle. Use

a paper clip or similar tool to

loosen the clog. Rinse thoroughly

with hot water. After all the

pieces are cleaned, place the

base then the pod holder

assembly into the brew head.

Lower the handle.

CAUTION: Sharp needles. Do not put

fingers in chamber.

Cleaning Entrance Needles

Lift the brewer handle and locate the top entrance needles on the

underside of the lid. To clean both holes in the needles, hold the

brewer handle in the upward position and with your other hand,

carefully insert a straightened paper clip into the holes. Gently move

it around to loosen any coffee grounds. Lower the handle completely

and run two water-only brew cycles. Do not insert a K-Cup® pod.

TIP: Refer to support.Keurig.com for video instructions on cleaning the

entrance/exit needles.

NOTE: You can also use a Brewer Maintenance Accessory tool to clean the entrance

needles. Reach out to Customer Service to get a Brewer Maintenance Accessory.

Drip Tray

The drip tray can hold up to 8 ounces of overflow and should be

emptied and cleaned occasionally. To remove, slide it toward you,

keeping it level to avoid spilling. Rinse and clean with a damp, soapy,

lint-free, non-abrasive cloth.

Water Reservoir & Reservoir Lid

The water reservoir lid and water reservoir should be periodically

cleaned with a damp, soapy, non-abrasive cloth and rinsed

thoroughly. The water reservoir lid and water reservoir should

not be put into the dishwasher. Do not dry the inside of the water

reservoir with a cloth as lint may remain. If needed, repeat

above procedures.

CAUTION: Please rinse the water reservoir thoroughly after cleaning. This will ensure

that no cleaning solutions remain in this area as they may contaminate the water supply

in the brewer.

Recycling K-Mug® and K-Carafe® Pods

The plastic cups of K-Mug® and K-Carafe® pods can be recycled wherever #5 plastic is accepted. #5 plastic

may not be recyclable in your community today, so please check locally with your municipality or waste

hauler, or visit KeurigRecycling.com for more information. #5 plastic is recyclable everywhere in Canada.

Once separated,

discard the lid and the

attached filter. Recycle

the plastic cup wherever

#5 plastic is accepted.

Once brewing is

complete and pod is

cool, separate the lid

and filter from the cup.

The filter will adhere

to the lid.

Keurig Green Mountain, Inc.

33 Coffee Lane

Waterbury, VT 05676

1.866.901.BREW (2739)

P/N | Pièce nº | Pieza n.

º DC0000001092 REV B 09/17

Access Settings

Explore everything your Keurig®

Plus Series brewer has to offer

by accessing the Settings Menu.

From the home screen, select

the settings button.

Use the arrows to scroll through

the menu. To exit, press the

back button.

For all settings, press to confirm your selection or use the to return to the Settings Menu.SAVE BACK BUTTON

Choose Language

Press English, Spanish, or

French to select the language.

Set Clock

Time: Set the current time using

the arrows, then choose AM

or PM.

Display: Choose DIGITAL or

ANALOG. For digital only, use

the toggle to select 12 HR or 24

HR (military).

TIME

11:32

SAVE

12 HR 24 HR

DIGITAL ANALOG

12:00

SAVE

DISPLAY

Temperature

The temperature setting

provides even more control over

the brewing process.

Use the left and right arrows

to choose from low, low/

medium, medium, medium/high,

and high.

High Altitude

To ensure your brewer works

properly at higher altitudes

(5,000 feet), ENABLE the high

altitude mode.

Wallpaper

You can customize your touch-

screen color. Simply press

a color window to select a

wallpaper for the home screen.

Nightlight

Choose the color of your home

screen and set on and off times

to provide a warm glow in your

kitchen at night.

Nightlight Color: Choose white,

green, blue, or red.

Nightlight Off: Select ENABLE to

set the time the nightlight should

turn off. Use the arrows to set

the time for the home screen to

change color.

Nightlight On: Select ENABLE to

activate the nightlight timer. Use

the arrows to set the time for

the home screen to change color.

If you are using a Keurig® Water

Filter, select ENABLE to activate

the water filter reminder.

Water Filter Reminder

Restore Factory Settings

Press YES to restore your brewer

to the default settings.

Restoring defaults erases

preferred brew settings,

temperature, wallpaper, auto

on/off, and nightlight settings.

The clock will be set to 12:00 AM.

Press NO to return to the

Settings Menu.

Settings Menu

PREFERRED BREW SETTINGS

K-CUP

1 OF 3

Auto On/Off

You can leave your brewer on at

all times so it is always ready to

make your perfect cup, or you

can set the auto on, auto off,

or energy saver mode.

Energy Saver: Set the brewer

to turn off in increments of 15

minutes after the last brew.

Auto Off: Select ENABLE to

activate auto off. Use the

arrows to set the time for

the brewer to automatically

turn off.

Preferred Brew Settings

The preferred brew settings

menu allows you to change

the default settings for each

KEURIG BREW number.

See the Settings and Touch

Screen Controls page for a

full list of available KEURIG

BREW settings.

Use the arrows to set your

preferred brew setting. Press

SAVE to confirm your selection

or use the BACK BUTTON to

return to the Settings Menu.

SAVE

TURN BREWER OFF WHEN IDLE FOR:

0:15

ENABLE

SAVE

TURN BREWER ON AT:

7:00

ENABLE

SAVE

TURN BREWER OFF AT:

10:00

ENABLE

AUTO ON/OFF

AUTO ON

AUTO OFF

ENERGY SAVER

Water Reservoir Light

Choose white, green, blue,

or red.

BACK BUTTON

SETTINGS

Descaling Your Brewer

You should descale your brewer every 3-6 months. Properly follow

the descaling procedure.

Depending on the mineral content of your water, calcium deposits

or scale may build up in your brewer. Scale is non-toxic but if left

unattended can hinder brewer performance. Regularly descaling

your brewer every 3-6 months helps maintain the heating element,

and other internal parts that come in

contact with water. Calcium deposits

may build up faster, making it necessary

to descale more often. You should

promptly descale when the touch screen

indicates “Time to descale the brewer!”

Descaling Procedure

Before you begin, you will need a large ceramic mug, fresh water,

Keurig® Descaling Solution, and access to a sink. Do not use a paper

cup. Ensure that there is no beverage pod in the K-Cup® pod holder.

Please allow approximately 45 minutes for the descaling procedure.

Empty the water from the water reservoir. If there is a Keurig®

Water Filter, remove and set aside.

STEP 1: Descaling Solution Rinse

Press and hold the power button to power the brewer off.

Pour the entire bottle of Keurig® Descaling Solution into an emptied

water reservoir. Then fill the empty bottle with water and pour into

the water reservoir. Press and hold the power button to turn the

brewer back on.

Place a large mug on the drip tray and run a cleansing brew by

lifting and lowering the handle, selecting the largest brew size and

pressing the brew button.

STEP 2: Descaling Rinse & Repeat

Repeat the rinsing brew process until the touch screen indicates

“More Water Please”. Do not use a K-Cup® pod. Let the brewer

stand for at least 30 minutes while still on.

After 30 minutes, discard any residual solution from the water

reservoir and rinse thoroughly.

STEP 3: Fresh Water Rinse

Fill the water reservoir with fresh water to and not beyond the

MAX line.

Place a large mug on the drip tray plate and run a rinsing brew using

the largest brew size.

Do not use a K-Cup® pod. Pour the contents of the mug into the sink.

Repeat brew process until you have completed at least 12 rinsing

brews. You may need to refill the water reservoir at least one time

during this process.

NOTE: The cleaning action of Keurig® Descaling Solution may result in a “foam”

dispensed from the brewer. This is natural, as the solution is reacting with the scale inside.

For a brewer that is heavily scaled, the brewer may not fill properly after the descaler is

added. If this occurs, you may see only a small or no output dispensed, followed by the

sound of air blowing out. If this occurs:

Turn off and unplug the brewer.

If there is Keurig® descaling solution in the water reservoir, discard the contents,

rinse the water reservoir thoroughly and refill with water.

Plug the brewer back in, power on, and repeat the Step 3 Fresh Water Rinse cycle.

The brewer should begin to function normally as the solution is rinsed out and the

scale is removed. If problem persists, allow brewer to sit unplugged for at least 30

minutes before continuing with the rinse.

NOTE: If “Time to descale the brewer!” alert is still indicated on the touch screen, repeat

the descaling procedure.

CONTINUE

Time to descale

the brewer!

NOT NOW

Warranty

LIMITED ONE YEAR WARRANTY

Keurig Green Mountain, Inc. (Keurig) warrants that your brewer will

be free of defects in materials or workmanship under normal home

use for one year from the date of purchase. It is recommended

that you register your brewer on Keurig.com/new so that your

purchase information will be stored in our system. Keurig will, at its

option, repair or replace a defective brewer without charge upon its

receipt of proof of the date of purchase. If a replacement brewer is

necessary to service this warranty, the replacement brewer may be

new or reconditioned. If a replacement brewer is sent, a new limited

one year warranty will be applied to the replacement brewer.

This warranty only applies to brewers operated in the United States

and Canada. This warranty gives you specific legal rights, and you

may also have other rights that vary from state to state and, in the

case of Canada, from province to province.

Only the use of Keurig® K-Cup® brand pods and accessories will

guarantee the proper functioning and lifetime of your Keurig®

brewer. Any damage to or malfunction of your brewer resulting

from the use of non-Keurig® pods and accessories may not be

covered by this warranty or may result in a service fee if the

damage or malfunction is determined to be caused by such use.

OTHER LIMITATIONS

THIS WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY

OTHER EXPRESS WARRANTY, WHETHER WRITTEN OR ORAL.

IN ADDITION, KEURIG HEREBY SPECIFICALLY DISCLAIMS

ALL OTHER WARRANTIES WITH RESPECT TO YOUR K500

SERIES BREWER, INCLUDING ANY IMPLIED WARRANTY OF

MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE.

Some states or provinces do not allow disclaimers of such implied

warranties or limitations on how long an implied warranty lasts, so

the above limitation may not apply to you depending on the state or

the province of purchase.

HOW DO YOU OBTAIN WARRANTY SERVICE?

Keurig® brewers are high-quality appliances and, with proper care,

are intended to provide years of satisfying performance. However,

should the need arise for warranty servicing, simply call Keurig

Customer Service at our toll free phone number 1.866.901.BREW

(2739). Please do not return your brewer for servicing without first

speaking to Keurig Customer Service to obtain a Return Materials

Authorization (RMA) number. Keurig® brewers returned without a

RMA number will be returned to the sender without servicing.

WHAT IS NOT COVERED BY THE LIMITED WARRANTY?

THIS WARRANTY DOES NOT COVER CONSEQUENTIAL OR

INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND DOES

NOT COVER INCIDENTAL COSTS AND EXPENSES RESULTING

FROM ANY BREACH OF THIS WARRANTY, EVEN IF FORESEEABLE.

Some states or provinces do not allow the exclusion or limitations

of incidental or consequential damages, so the above limitation or

exclusion may not apply to you depending on the state or province

of purchase.

Nor does this warranty cover damages caused by use of non-Keurig®

pods or accessories, services performed by anyone other than

Keurig or its authorized service providers, use of parts other than

genuine Keurig® parts, or external causes such as abuse, misuse,

inappropriate power supply, or acts of God.

your new Keurig® brewer

and receive a special

savings offer

your favo te coff s w hri ee it

our customized tast quiz e and

get personalized reco smm daten ion

Fully experience the benefits th t a come with your new Keurig® brewer at

KEURIG.COM/NEW

Auto On: Select ENABLE to

activate auto on. Use the

arrows to set the time for the

brewer to automatically turn on.

•

brewer

Before You Brew

Plug & Place

Remove packing tape

from brewer and plug

into a grounded outlet.

Place a large mug (12 oz.

minimum) on the drip tray plate.

Rinse & Fill

Remove the water

reservoir lid, then lift the

reservoir straight up to remove it.

Rinse reservoir with fresh water

and fill to the MAX line.

Replace water reservoir, making

sure the lock tabs engage with

the brewer. Replace lid.

NOTE: Do not use distilled water.

Power On

Press the power

button. Lift the

handle—remove and discard

the orange shipping disk.

Lower the handle. Wait for

preheating to complete,

about 3 minutes.

Cleansing Brew Setup

Press the hot water

button and then press

the blinking brew button to

start a cleansing brew. Pour

the hot water into the sink.

The one-time setup process is

now complete and you are ready

to brew!

2.0

HOT WATER

BREW BUTTON

Set Carafe Auto Brew Mode

Make sure the Keurig®

Carafe is empty. Remove

the drip tray and insert

the Keurig® Carafe

securely in its place.

Select a K-Carafe®

pod, place firmly in the

pod holder and lower

the handle.

NOTE: Ensure the current time

is accurate. Refer to Set Clock

instructions in the Settings

Menu in this guide to adjust.

To put the brewer in

sleep mode, quickly

press and release the

power button.

To cancel the carafe

auto brew mode,

remove the Keurig®

Carafe or lift the handle.

Select AUTO BREW

PRESS TO SET.S

Select the time

you want to begin

brewing, then press

the right arrow.

Select a brew size,

then press SET.p

The touch screen

will indicate

DO NOT DISTURB!

To edit any options,

select TOUCH HERE

TO EDIT.

AUTO BREW

PRESS TO SET

AUTO BREW CARAFE AT:

CANCEL

6:00

AUTO BREW CARAFE SIZE:

SET

CARAFE SET TO

AUTO BREW AT: 6:00

TOUCH HERE TO EDIT

DO NOT DISTURB!

CARAFE SET TO

AUTO BREW AT: 6:00

TOUCH HERE TO EDIT

DO NOT DISTURB!

CARAFE SET TO

AUTO BREW AT: 6:00

TOUCH HERE TO EDIT

DO NOT DISTURB!

K500 S ies Brer ewer

Troubleshooting

Brewer Does Not Have Power or Shuts Off

•

Brewing a Partial Cup

• The exit needle may be clogged. Refer to the Exit Needle

care instructions.

The water reservoir may have been removed during brewing.

Replace the water reservoir and perform a rinsing brew

without a K-Cup® pod.

The brewer may need to be descaled. If you have repeated

the descale procedure on your brewer two times and it is still

only brewing a partial cup, contact Customer Service.

•

Touch Screen Alerts

• “More Water Please” – If the water level is not low, remove

the water reservoir and empty the water. Clean the reservoir.

Return the reservoir to the brewer and ensure it is seated

properly in its base.

“Sorry, Brew Interrupted” – Slowly lift the handle, remove the

pod, lower the handle and perform a rinsing brew.

“Sorry, There is a Problem” – Coffee grounds may be stuck in the

entrance needle. Refer to Caring For Your Brewer for cleaning

instructions.

“Time To Replace the Keurig® Water Filter” – Your brewer will

indicate that it is time to replace the water filter after every

1,000 ounces or two months. Once you’ve replaced the Keurig®

Water Filter press YES to reset the water filter reminder.

•

Brewer Shuts Off Or Turns On Automatically

• Check to make sure that the AUTO ON/OFF settings have not

been set. Refer to the Settings Menu.

Brewer Will Not Brew

• After placing a pod in the pod holder, make sure the handle

is lowered completely and the touch screen displays the

appropriate brew screen. Follow the brewing instructions.

If the touch screen indicates “More Water Please” add water to

the water reservoir or make sure the water reservoir is seated

properly in its base.

If the touch screen indicates “More Water Please” even after

refilling, remove the water reservoir and empty the water. Then

thoroughly clean the reservoir. Fill the water reservoir to the

MAX line, return it to the brewer and ensure it is seated properly

in its base.

The pod holder may need to be cleaned or the brewer may need

to be descaled. Refer to Caring For Your Brewer for instructions.

•

Grounds in Your Coffee

Grounds may have gathered in the exit or entrance needles and can

be cleaned using a straightened paper clip or similiar tool.

• Clean the exit needle of the K-Cup® pod holder. Refer to the

Exit Needle care instructions.

Clean the brewer entrance needles. Refer to the Entrance

Needles care instructions.

•

Settings and Touch Screen Controls

Home Screen

A. Settings Button

B. Hot Water Button

C. Power Button

Brew Settings

Select the KEURIG BREW setting that matches the number on the

pod lid for K-Mug® and K-Carafe® pods.

Screen for K-Cup® Pods

A. STRONG (only available for

coffee)

B. HOT COCOA/OTHER (for

select non-coffee beverages)

C. Brew Size

D. Power Button

Screen for K-Carafe® Pods

A. KEURIG BREW Setting 1

B. Auto Brew (only available for

K-Carafe® pods)

C. Brew Size

D. Power Button

* DEFAUL SIZET

Helpful Hints

Water quality varies greatly. If you notice an undesirable taste in

your beverage (such as chlorine or mineral tastes), we recommend

using bottled or filtered water. Do not use distilled water. You can

also install a Keurig® Water Filter to help remove water impurities

and improve beverage taste.

Service

Beyond these recommended cleaning and maintenance procedures,

this brewer is not user serviceable. For service, please refer to the

Warranty section of this guide.

Storage

Empty the water reservoir before storing or transporting and take

care to ensure that you store your brewer in a safe and frost free

environment. Please be sure to store your brewer in its upright

position to avoid water leakage from the inner tank. If you store

the brewer in a cold environment, you run the risk of water freezing

inside the brewer and causing damage. When you prepare to use it

after storage, we recommend rinsing the water reservoir with fresh

water and running three rinsing brews without a K-Cup® pod.

If you plan to move your brewer to a different location, turn the

brewer off, unplug it, and empty the water reservoir. If your brewer

has been in an environment below freezing, please be sure to let it

warm to room temperature for at least 2 hours before using.

Have Questions?

We’re here to help. Visit for step-by-step videos support.Keurig.com

on cleaning, descaling, and more.

Still Need Help?

Give us a call at

1-866-901-BREW (2739)

Click or Call!

Brew Your First K-Cup® Pod

Place Mug

Place a mug on the

drip tray plate. If using

a travel mug, remove the drip

tray and place the mug on the

drip tray base.

Hot Water on Demand: To dispense

hot water into a mug, press the hot

water button, then select your cup size.

Press the brew button. When the brew

process is complete, the touch screen

will indicate Enjoy!

NOTE: Between brew cycles, the brewer

may take about a minute to reheat.

Lift & Insert

Lift the handle and

place a K-Cup® pod

in the K-Cup® pod holder.

Lower the handle completely

to close the lid.

Do not remove the foil lid

on the K-Cup® pod.

Size & Strength

Select your brew size

using the arrows on

the screen. Select STRONG

if desired. (STRONG setting

is for coffee.) Press HOT

COCOA/OTHER for select

non-coffee beverages.

NOTE: Make sure to check instructions on

pod packaging.

CAUTION: There is extremely hot water in

the K-Cup® pod during the brew process.

To avoid injury, do not lift the handle

during the brew process.

Brew & Enjoy

Press the blinking

brew button. The

button will remain illuminated

while brewing, about 1 minute.

The brewer will notify you when

the brew cycle is complete.

Lift the handle and dispose

of the used K-Cup® pod. The

brewer will be ready to brew

another cup in about a minute.

NOTE: To stop the brewing process, press

and hold the power button for one second.

READY

STRONG

HOT

COCOA

OTHER

READY

STRONG

HOT

COCOA

OTHER

HOT WATER

Brew Your First K-Carafe® Pod

Place Carafe

Make sure the Keurig®

Carafe is empty.

Remove the drip tray and insert

the Keurig® Carafe securely in

its place.

Lift & Insert

Lift the handle and

place a K-Carafe®

pod in the pod holder.

Lower the handle completely

to close the lid.

Do not remove the foil lid or

puncture the K-Carafe® pod.

Select Brew Size

Select the KEURIG

BREW setting that

matches the number on the pod

lid. Then select the number of

desired cups.

NOTE: Make sure the number on the

touch screen matches the number on the

K-Carafe® pod in the pod holder.

CAUTION: There is extremely hot water

in the K-Carafe® pod during the brew

process. To avoid injury, do not lift the

handle during the brew process.

Brew & Enjoy

Press the blinking

brew button. The

button will remain illuminated

while brewing.

The brewer will notify you when

the brew cycle is complete.

Lift the handle and dispose of

used K-Carafe® pod.

NOTE: To stop the brewing process, press

and hold the power button for one second.

AUTO BREW

PRESS TO SET

Flip-Top Reservoir Lid

Water Reservoir

Top Housing

Touch Screen/Power Button

Brew Button

Handle

Brew Head

Power Cord

Drip Tray Plate

Drip Tray

Pod Holder

Housing (K and L are the Pod Holder Assembly)

Base

K500 Series

Use & Care Guide

Get e th most from your

new Keurig® brewer.

Press and hold the power button and ensure the touch screen

is illuminated.

Plug brewer into its own grounded outlet. If the electric circuit is

overloaded with other appliances, your brewer may not function

properly. The brewer should be operated on its own circuit,

separate from other appliances.

If the brewer still doesn’t have power, contact Customer Service.

Termékspecifikációk

Márka:	Keurig
Kategória:	Kávéfőző
Modell:	K575

Szüksége van segítségre?

Ha segítségre van szüksége Keurig K575, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek

Az Ön neve*

Az Ön e-mail címe*

Írja ide kérdését

Útmutatók Kávéfőző Keurig

Keurig K-Cup 2.0 Brewer K350 Útmutató

12 Január 2025

Keurig K-Mini Go Útmutató

31 Augusztus 2024

Keurig K•Café Útmutató

28 Augusztus 2024

Keurig K-10 Mini Plus Brewer Útmutató

24 Augusztus 2024

Keurig Vue V 1200 Útmutató

24 Augusztus 2024

Keurig 2.0 K450 Brewer Útmutató

24 Augusztus 2024

Keurig Vue V 700 Útmutató

24 Augusztus 2024

Keurig K-45 Elite Brewer Útmutató

24 Augusztus 2024

Keurig Vue V 500 Útmutató

24 Augusztus 2024

Keurig K-Cup K45 Elite Brewer Útmutató

16 Augusztus 2024

Útmutatók Kávéfőző

Legújabb útmutatók Kávéfőző

Espressions EP1032 Junior Útmutató

10 Április 2025

Veromatic International Melange d Or Vista Espresso Útmutató

10 Április 2025

Bialetti Moka Express 3 Útmutató

10 Április 2025

Bialetti Moka Express 2 Útmutató

9 Április 2025

Bravilor Bonamat RLX 131 Útmutató

7 Április 2025

Aroma AEM-108 Útmutató

7 Április 2025

Cloer 5021 Útmutató

6 Április 2025

Electra Micro Casa Útmutató

5 Április 2025

Bodum 1928-18 Útmutató

4 Április 2025

Jura IMPRESSA XJ9 Professional Útmutató

2 Április 2025