Használati útmutató Kemppi A7 TIG Orbital System 300
Kemppi
Hegesztő készülék
A7 TIG Orbital System 300
Olvassa el alább 📖 a magyar nyelvű használati útmutatót Kemppi A7 TIG Orbital System 300 (61 oldal) a Hegesztő készülék kategóriában. Ezt az útmutatót 3 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra
Oldal 1/61
300
1920390
1615
A7 TIG Orbital System
EN
OPERATING MANUAL
2A7 TIG Orbital System 300© Kemppi Oy 2016 1615
OPERATING MANUAL
CONTENTS
1. Introduction ..........................................................................................4
1.1 General ......................................................................................................4
1.2 About the product ....................................................................................5
1.3 Weld head .................................................................................................. 6
1.3.1 General specications .............................................................................6
1.4 Controller unit ...........................................................................................7
1.4.1 Remote control ......................................................................................7
1.5 Compatibility .............................................................................................8
2. Installation .............................................................................................9
2.1 Controller connections .............................................................................9
2.2 Water cooler ............................................................................................10
2.2.1 Filling water cooler with coolant ............................................................10
2.2.2 Operating the water ow .......................................................................10
2.3 Weld head set-up ....................................................................................11
2.3.1 Assemblies ..........................................................................................11
2.4 Installing guide ring on tube ..................................................................13
2.5 Mounting the weld head ........................................................................14
2.6 Wire spool ................................................................................................15
2.7 Electrode ..................................................................................................16
2.8 Torch centering .......................................................................................17
2.9 Mechanical adjustments .........................................................................17
3. Operation .............................................................................................18
3.1 Welding settings .....................................................................................18
3.1.1 Setting current level ..............................................................................18
3.1.2 Pulsillation (synchronized pulsed current/oscillation mode)..........................18
3.1.3 Filler wire speed ...................................................................................18
3.1.4 Root-pass procedure .............................................................................19
3.1.5 Hot-pass procedure ..............................................................................19
3.1.6 Fill passes, oscillation (weave), and stringer bead techniques ........................20
3.1.7 Shield gas eects ..................................................................................21
3.2 Preparing the work piece ........................................................................21
3.2.1 Groove preparation ...............................................................................21
3.2.2 Joint design and t-up tolerance ............................................................21
3.2.3 Other preparations ...............................................................................22
3.2.4 Developing weld procedures/process parameters ......................................22
3.3 Controller unit menus .............................................................................23
3.3.1 Main Menu ..........................................................................................23
3.3.2 Maintenance Menu ...............................................................................25
3.3.3 Options Menu ......................................................................................27
3.3.4 Compatible weld head models ................................................................28
3.3.5 Calibrate head .....................................................................................28
3.3.6 300-head guide ring speed factors ...........................................................29
3.3.7 Advanced Help ....................................................................................30
3.3.8 Autotack .............................................................................................30
3.3.9 Autoprogram .......................................................................................31
3.4 Alphanumeric labelling ...........................................................................33
3.5 Manual programming .............................................................................33
3.6 Prepurge – Upslope.................................................................................37
3.7 Programmed oscillation width (without striking an arc) .......................37
3.8 Editing a weld program...........................................................................38
3.9 Completing the programming ...............................................................39
3.10 Updating software ..................................................................................39
3.11 Welding ...................................................................................................39
3.12 Travel speed correction ...........................................................................39
3.13 Shielding gas ...........................................................................................40
3.13.1 Purging the pipe ID with inert gas ...........................................................41
4. Additional details ..............................................................................42
4.1 Controller technical data .........................................................................42
4.2 Weld head technical data........................................................................42
4.3 Ordering information ..............................................................................43
3A7 TIG Orbital System 300© Kemppi Oy 2016 1615
OPERATING MANUAL
5. Troubleshooting ................................................................................46
5.1 Operation problems ................................................................................46
5.2 Root-pass renement for horizontal pipe (5G position) ........................47
5.3 Common weld defects: identication and prevention ..........................48
5.4 Warnings/error messages ......................................................................49
5.5 Checking machine setup during booting ..............................................53
5.6 Machine system messages......................................................................54
5.7 Controller unit fault conditions ..............................................................54
6. Maintenance .......................................................................................55
6.1 Preventing tungsten electrode rotation not concentric to tube OD .....55
6.2 Periodic maintenance .............................................................................55
6.3 Weld head maintenance .........................................................................56
6.3.1 External maintenance............................................................................56
6.3.2 Low prole kit installation ......................................................................56
6.3.3 Torch cable replacement ........................................................................56
6.3.4 Maintenance of the wire feed nozzle ........................................................56
6.3.5 Water cooler maintenance/ushing procedure for the torch cable .................57
6.3.6 Maintenance of torch components ..........................................................57
6.3.7 Cleaning the weld head .........................................................................58
6.3.8 Internal arcing .....................................................................................58
6.4 Printer operation and maintenance .......................................................59
6.4.1 Installing paper in the printer..................................................................59
6.4.2 Cleaning the printer ..............................................................................59
6.5 Service Workshop maintenance ............................................................59
7. Disposal ................................................................................................60
Termékspecifikációk
| Márka: | Kemppi |
| Kategória: | Hegesztő készülék |
| Modell: | A7 TIG Orbital System 300 |
Szüksége van segítségre?
Ha segítségre van szüksége Kemppi A7 TIG Orbital System 300, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek
Útmutatók Hegesztő készülék Kemppi
5 Október 2024
22 Szeptember 2024
22 Szeptember 2024
22 Szeptember 2024
21 Szeptember 2024
20 Szeptember 2024
20 Szeptember 2024
17 Szeptember 2024
21 Augusztus 2024
20 Augusztus 2024
Útmutatók Hegesztő készülék
- Hegesztő készülék Parkside
- Hegesztő készülék GYS
- Hegesztő készülék Kinzo
- Hegesztő készülék Weldkar
- Hegesztő készülék Frilass
- Hegesztő készülék Elektra Beckum
- Hegesztő készülék DEKO
Legújabb útmutatók Hegesztő készülék
17 Szeptember 2024
24 Augusztus 2024
23 Augusztus 2024
23 Augusztus 2024
23 Augusztus 2024
23 Augusztus 2024
23 Augusztus 2024
23 Augusztus 2024
23 Augusztus 2024
23 Augusztus 2024