Használati útmutató Kemppi A7 MIG Power Source 350
Kemppi
Hegesztő készülék
A7 MIG Power Source 350
Olvassa el alább 📖 a magyar nyelvű használati útmutatót Kemppi A7 MIG Power Source 350 (67 oldal) a Hegesztő készülék kategóriában. Ezt az útmutatót 3 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra
Oldal 1/67
350, 450
1920300
1824
A7 MIG WelderA7 MIG Welder
EN
OPERATING MANUAL
2A7 MIG Welder© Kemppi Oy 2018 1824
OPERATING MANUAL
CONTENTS
1. Introduction ..........................................................................................4
2. Installation .............................................................................................5
3. System Overview ................................................................................6
3.1 Power Source ............................................................................................. 6
3.2 Robot interface unit ..................................................................................7
3.3 User interfaces ........................................................................................... 8
3.4 A7 MIG Wire Feeder 25 ..............................................................................9
3.5 MIG Guns .................................................................................................11
3.6 Cooling unit .............................................................................................12
3.7 I/O device.................................................................................................13
4. Using the welder ...............................................................................14
4.1 Basic controls ...........................................................................................14
4.2 Setup panel .............................................................................................14
4.2.1 Button functions ..................................................................................15
4.2.2 Main menu ..........................................................................................16
4.2.3 Memory channel wizard ........................................................................16
4.2.4 User settings ........................................................................................22
4.2.5 Welding system settings ........................................................................22
4.2.6 System tests ........................................................................................25
4.2.7 Robot settings .....................................................................................26
4.3 Web user interface ..................................................................................29
4.3.1 Welding display....................................................................................30
4.3.2 Gas, air and wire inch ............................................................................30
4.3.3 Logbook .............................................................................................31
4.3.4 About .................................................................................................31
4.3.5 Welding settings – Memory channels .......................................................31
4.3.6 Settings – Language .............................................................................35
4.3.7 Settings – Users ....................................................................................35
4.3.8 Settings – Change PIN ...........................................................................35
4.3.9 Settings – Fieldbus................................................................................36
4.3.10 Settings – Network ...............................................................................36
4.3.11 Settings – Backup, restore and reset .........................................................37
4.3.12 Settings – Licenses ................................................................................37
4.4 User identication ...................................................................................38
4.4.1 Overview ............................................................................................38
4.4.2 Turning user identication system on .......................................................39
4.4.3 Creating new users ...............................................................................39
4.4.4 Deleting a user .....................................................................................40
4.4.5 Changing user role ...............................................................................40
4.4.6 Changing username ..............................................................................40
4.4.7 Changing PIN code ...............................................................................40
4.4.8 Resetting PIN code ...............................................................................41
4.4.9 Logging in and out, changing active user ..................................................41
4.5 Touch sensor (seam search) ....................................................................42
4.5.1 Voltage source, levels and safety .............................................................44
4.5.2 Touch tool ...........................................................................................45
4.5.3 Fast status output .................................................................................45
4.5.4 Selecting output voltage .......................................................................45
4.5.5 Conguring touch tool ..........................................................................46
4.6 Through Arc Seam Tracking (TAST) ........................................................46
4.7 Collision sensor .......................................................................................47
4.7.1 Setting collision sensor on and o ...........................................................48
4.7.2 Selecting sensor type ............................................................................48
4.7.3 Selecting output polarity .......................................................................48
4.8 Wire feeder ..............................................................................................49
4.8.1 Loading the ller wire ...........................................................................49
4.9 Arc measurement ....................................................................................53
4.9.1 Setup and calibration ............................................................................53
4.9.2 Display ...............................................................................................53
3A7 MIG Welder© Kemppi Oy 2018 1824
OPERATING MANUAL
4.10 Gas ow sensor .......................................................................................54
4.10.1 On/O control .....................................................................................54
4.10.2 Gas ow sensing level ...........................................................................54
4.10.3 Gas mixture setup ................................................................................55
5. Troubleshooting ................................................................................56
5.1 Typical problems .....................................................................................56
5.2 Error codes ...............................................................................................57
5.2.1 Power source errors ..............................................................................57
5.2.2 Cooling unit errors ................................................................................58
5.2.3 Wire feeder errors .................................................................................59
5.2.4 Welding curve errors .............................................................................59
5.2.5 Robot interface errors............................................................................60
5.2.6 I/O device errors ...................................................................................61
6. Operation disturbances ..................................................................62
7. Maintenance .......................................................................................63
7.1 Daily maintenance ..................................................................................63
7.2 Periodic maintenance .............................................................................63
7.3 Service shop maintenance ......................................................................63
8. Disposal ................................................................................................64
9. Ordering numbers ............................................................................64
10. Technical data ....................................................................................65
Termékspecifikációk
| Márka: | Kemppi |
| Kategória: | Hegesztő készülék |
| Modell: | A7 MIG Power Source 350 |
Szüksége van segítségre?
Ha segítségre van szüksége Kemppi A7 MIG Power Source 350, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek
Útmutatók Hegesztő készülék Kemppi
5 Október 2024
22 Szeptember 2024
22 Szeptember 2024
22 Szeptember 2024
21 Szeptember 2024
20 Szeptember 2024
20 Szeptember 2024
17 Szeptember 2024
21 Augusztus 2024
20 Augusztus 2024
Útmutatók Hegesztő készülék
- Hegesztő készülék Parkside
- Hegesztő készülék GYS
- Hegesztő készülék Kinzo
- Hegesztő készülék Weldkar
- Hegesztő készülék Frilass
- Hegesztő készülék Elektra Beckum
- Hegesztő készülék DEKO
Legújabb útmutatók Hegesztő készülék
17 Szeptember 2024
24 Augusztus 2024
23 Augusztus 2024
23 Augusztus 2024
23 Augusztus 2024
23 Augusztus 2024
23 Augusztus 2024
23 Augusztus 2024
23 Augusztus 2024
23 Augusztus 2024