Használati útmutató Kemppi A5 TIG Orbital System 75
Kemppi
Hegesztő készülék
A5 TIG Orbital System 75
Olvassa el alább 📖 a magyar nyelvű használati útmutatót Kemppi A5 TIG Orbital System 75 (33 oldal) a Hegesztő készülék kategóriában. Ezt az útmutatót 3 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra
Oldal 1/33
75
1920370
1615
A5 TIG Orbital System
EN
OPERATING MANUAL
2A5 TIG Orbital System 75© Kemppi Oy 2016 1615
OPERATING MANUAL
CONTENTS
1. Introduction ..........................................................................................3
1.1 General ......................................................................................................3
1.2 About the product ....................................................................................4
1.3 Weld head .................................................................................................. 5
1.3.1 Tube diameters and weld head outline dimensions .......................................5
1.3.2 Collets ..................................................................................................6
1.3.3 Collet frame and collets ...........................................................................6
1.3.4 Flush collets ..........................................................................................7
1.3.5 Extended collets / combination .................................................................7
1.4 Controller unit ...........................................................................................8
1.5 TIG power source.......................................................................................8
1.6 Tube preparation ......................................................................................8
2. Installation .............................................................................................9
2.1 Connecting the weld head .......................................................................9
2.2 Installing collets on the weld head .........................................................10
2.3 Mounting the weld head ........................................................................10
3. Operation .............................................................................................11
3.1 Rotor gear ................................................................................................11
3.2 Tungsten electrode .................................................................................11
3.2.1 Tungsten electrode diameter and length ..................................................11
3.2.2 Installing the tungsten electrode and holder .............................................12
3.2.3 Tungsten electrode geometry guidelines ..................................................12
3.3 Electrode sharpeners ..............................................................................13
3.4 Weld head control panel .........................................................................14
3.5 Controller unit control panel .................................................................14
3.5.1 Quick guide to start welding ...................................................................14
3.5.2 Main/Home screen ...............................................................................15
3.5.3 Initial setup screen ................................................................................15
3.5.4 Program storage (Library) ......................................................................15
3.5.5 Weld Programs – selecting a weld program 1–10 ........................................16
3.5.6 Calibrating weld head or power source output ...........................................16
3.5.7 Calibrating weld power source current output ...........................................17
3.5.8 Selecting power source .........................................................................18
3.5.9 Pulsed/non-pulsed welding ....................................................................18
3.5.10 Gas purge ...........................................................................................19
3.5.11 Preparing welding – test weld .................................................................20
3.5.12 Icons and screens during welding ...........................................................21
3.6 Equipment stop ......................................................................................22
3.7 Updating software ..................................................................................22
4. Additional details ..............................................................................23
4.1 Technical data ..........................................................................................23
4.2 Ordering information ..............................................................................23
4.2.1 Ordering collets ...................................................................................24
4.2.2 Collets ................................................................................................24
4.2.3 Tungsten electrode material and ordering information ................................26
5. Troubleshooting ................................................................................29
5.1 Operation problems ................................................................................29
5.2 Warnings and error messages ................................................................30
5.3 Common weld defects ............................................................................31
6. Maintenance .......................................................................................31
6.1 Daily maintenance ..................................................................................31
6.2 Periodic maintenance .............................................................................31
6.3 Service Workshop maintenance ............................................................32
7. Disposal ................................................................................................32
3A5 TIG Orbital System 75© Kemppi Oy 2016 1615
OPERATING MANUAL
1. INTRODUCTION
1.1 General
Congratulations on choosing A5 TIG Orbital System 75
welding equipment. Used correctly, Kemppi products can
signicantly increase the productivity of your welding and
provide years of economical service.
This operating manual contains important information on
the use, maintenance and safety of your Kemppi product.
The technical specications of the equipment can be
found at the end of the manual.
Please read the operating manual and the safety
instructions booklet carefully before using the equipment
for the rst time. For your own safety and that of your
working environment, pay particular attention to the
safety instructions in the manual.
For more information on Kemppi products, contact
Kemppi Oy, consult an authorized Kemppi dealer, or visit
the Kemppi website at www.kemppi.com.
The specications presented in this manual are subject to
change without prior notice.
Important notes
Items in the manual that require particular attention in
order to minimise damage and harm are indicated with
below symbols. Read these sections carefully and follow
their instructions.
Note: Gives the user a useful piece of information.
Caution: Describes a situation that may result in
damage to the equipment or system.
Warning: Describes a potentially dangerous situation.
If not avoided, it will result in personal damage or fatal
injury.
Disclaimer
While every eort has been made to ensure that the
information contained in this guide is accurate and
complete, no liability can be accepted for any errors
or omissions. Kemppi reserves the right to change the
specication of the product described at any time without
prior notice. Do not copy, record, reproduce or transmit
the contents of this guide without prior permission from
Kemppi.
Termékspecifikációk
| Márka: | Kemppi |
| Kategória: | Hegesztő készülék |
| Modell: | A5 TIG Orbital System 75 |
Szüksége van segítségre?
Ha segítségre van szüksége Kemppi A5 TIG Orbital System 75, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek
Útmutatók Hegesztő készülék Kemppi
5 Október 2024
22 Szeptember 2024
22 Szeptember 2024
22 Szeptember 2024
21 Szeptember 2024
20 Szeptember 2024
20 Szeptember 2024
17 Szeptember 2024
21 Augusztus 2024
20 Augusztus 2024
Útmutatók Hegesztő készülék
- Hegesztő készülék Parkside
- Hegesztő készülék GYS
- Hegesztő készülék Kinzo
- Hegesztő készülék Weldkar
- Hegesztő készülék Frilass
- Hegesztő készülék Elektra Beckum
- Hegesztő készülék DEKO
Legújabb útmutatók Hegesztő készülék
17 Szeptember 2024
24 Augusztus 2024
23 Augusztus 2024
23 Augusztus 2024
23 Augusztus 2024
23 Augusztus 2024
23 Augusztus 2024
23 Augusztus 2024
23 Augusztus 2024
23 Augusztus 2024