Használati útmutató JL Audio Slash 1200/1v3

JL Audio Vevő Slash 1200/1v3

Olvassa el alább 📖 a magyar nyelvű használati útmutatót JL Audio Slash 1200/1v3 (13 oldal) a Vevő kategóriában. Ezt az útmutatót 3 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/13
OWNER’S MANUAL
1200 W CLASS-D MONOBLOCK SUBWOOFER AMPLIFIER
Thank you for purchasing a JLAudio amplifier
for your automotive sound system.
Your amplifier has been designed and manufactured to exacting
standards in order to ensure years of musical enjoyment in your
vehicle. For maximum performance and extended warranty
coverage, we highly recommend that you have your new amplifier
installed by an authorized JLAudio dealer. Your authorized
dealer has the training, expertise and installation equipment
to ensure optimum performance from this product. Should you
decide to install the amplifier yourself, please take the time
to read this manual thoroughly so as to familiarize yourself
with its installation requirements and setup procedures.
If you have any questions regarding the instructions in this
manual or any aspect of your amplifier’s operation, please
contact your authorized JLAudio dealer for assistance. If you
need further assistance, please call the JLAudio Technical
Support Department at (954) 443-1100 during business hours.
2 | JL Audio - 1200/1 Owner’s Manual v3
Infrasonic Filter
Defeat Switch
(pg. 10)
Preamp Output
Filter Slope
Selector
(pg. 9)
Selects Output Filter
Cutoff Frequency
(pg. 10)
Selects Infrasonic
Filter Cutoff
Frequency
(pg. 10)
Selects Low-Pass
Filter Frequency fo
Amplifier Channe
(pg. 8)
Parametric EQ
"Q" (Bandwidth
Selection Control
(pg. 10)
R
Preamp Output
Mode Selector
(pg. 9)
Amplifier Low-Pas
Filter Slope
Selection / Defeat
(pg. 8)
Left and Right
Preamp Output Jacks
(pg. 9)
Bass EQ
Defeat Switch
(pg. 9)
Jack for
Remote Bass
Control Knob
(pg. 10)
Selects Low-Pass
or High-Pass Mode
for Output Filter
(pg. 10)
Remote Turn-On
Connector
(pg. 6)
Chassis Ground
Connector
(pg. 5)
+12 V Power
Connector
(pg. 5)
Parametric EQ
Center Frequency
Selection Control
(pg. 10)
Parametric EQ
Boost Control
(pg. 10)
+12VDC Ground Remote
Cooling Efficiency Considerations:
Your JLAudio amplifier employs an
advanced type of heat management, called
RealSink™. This feature takes advantage of
convection and radiation effects to remove
heat from the amplifier circuitry. For optimum
cooling performance, the vertical heat sinks
located at the back of the amplifier should be
exposed to as large a volume of air as possible.
Enclosing the amplifier in a small, poorly
ventilated chamber can lead to excessive heat
build-up and degraded performance. If an
installation calls for an enclosure around the
amplifier, we recommend that this enclosure
be ventilated with the aid of a fan. In normal
applications, fan-cooling is not necessary, but
you still need to follow some basic guidelines:
t"NQMJGJFSNPVOUFEWFSUJDBMMZXJUIIFBUTJOLGJOT
pointing up: Optimum
t"NQMJGJFSNPVOUFEIPSJ[POUBMMZ
right side up: Good
t"NQMJGJFSNPVOUFEIPSJ[POUBMMZCVUVQTJEF
down: Fair (not recommended if there is
less than 1 inch (2.5 cm) clearance above the
amplifier heat sinks)
t"NQMJGJFSNPVOUFEWFSUJDBMMZXJUIIFBUTJOLGJOT
pointing laterally: Fair
t"NQMJGJFSNPVOUFEWFSUJDBMMZXJUIIFBUTJOLGJOT
pointing down: Poor (not recommended)
ma
spa
pro
Sa
we
wh
equ
sys
sec
ha
eve
Stu
tC
to
th
o
t%
th
p
y
t1
ed
ty
lo
t%
co
o
am
PROTECT YOUR HEARING!
We value you as a long-term customer. For
that reason, we urge you to practice restraint in
the operation of this product so as not to damage
your hearing and that of others in your vehicle.
Studies have shown that continuous exposure to
high sound pressure levels can lead to permanent
(irreparable) hearing loss. This and all other
high-power amplifiers are capable of producing
such high sound pressure levels when connected
to a speaker system. Please limit your continuous
exposure to high volume levels.
While driving, operate your audio system in
a manner that still allows you to hear necessary
noises to operate your vehicle safely (horns,
sirens, etc.).
SERIAL NUMBER
In the event that your amplifier requires
service or is ever stolen, you will need to
have a record of the product’s serial number.
Please take the time to enter that number in
the space provided below. The serial number
can be found on the bottom panel of the
amplifier and on the amplifier packaging.
Serial Number:
INSTALLATION APPLICATIONS
This amplifier is designed for operation in
vehicles with 12V, negative-ground electrical
systems. Use of this product in vehicles with
positive ground and/or voltages other than 12V
may result in damage to the product and will void
the warranty.
This product is not certified or approved for
use in aircraft.
%POPUBUUFNQUUPiCSJEHFwUIFPVUQVUTPGUIJT
amplifier with the outputs of a second amplifier,
including an identical one.
PLANNING YOUR INSTALLATION
It is important that you take the time to read
this manual and that you plan out your
installation carefully. The following are some
considerations that you must take into account
when planning your installation.
4 | JL Audio - 1200/1 Owner’s Manual v3
POWER CONNECTIONS
Before installing the amplifier,
disconnect the negative (ground) wire
from the vehicle’s battery. This will prevent
accidental damage to the system, the vehicle
and your person during installation.
+12VDC Ground Remote
1200/1v3
Monoblock Subwoofer Amplifier
+12V Battery Connection
You will need to connect a power wire to
the vehicle’s positive battery terminal, using an
BQQSPQSJBUFQPXFSSJOHPSTQFDJBMJ[FECBUUFSZ
terminal connector, such as the JLAudio
9##56PS9%#545IJTDPOOFDUJPONVTU
be tight and corrosion-free to ensure proper
connectivity. This wire MUST be fused
appropriately for safety. Any power wires run
through metal barriers (such as firewalls), must
be protected with a high quality insulating
grommet to prevent damage to the insulation
of the wire. Failure to do so may result in a
dangerous short circuit.
Power Wire Requirements
The 1200/1v3’s “+12 VDC” and “Ground”
connections are designed to accept 4 AWG
power wire. 2 AWG or 1/0 AWG pure copper
wire is recommended for any power wire run
longer than 72 inches (180 cm). This larger
wire should be reduced to 4 AWG using a
distribution block within 36 wire inches (90
cm) of the amplifier’s “+12 VDC” connector.
For runs shorter than 72 inches, 4 AWG
pure copper power wire is acceptable.
If you are installing the 1200/1v3 with other
amplifiers and wish to use a single main power
wire, use 1/0 AWG pure copper wire as a main
power wire. This 1/0 AWG power wire should
terminate into a fused distribution block mounted
as close to the amplifiers as possible and should
connect to the 1200/1v3 with 4 AWG pure copper
power wire.
big
2 A
!
We
cla
thi
pu
wi
Ti
as
com
Fu
wi
bat
the
or
wi
FRV
no
tot
the
po
use
(la
fro
tog
we
fus
dis
am
ou
We
fus
dea
ho
for
yo
po
PRODUCT DESCRIPTION
The JLAudio 1200/1v3 is a monoblock
TVCXPPGFSBNQMJGJFSVUJMJ[JOHQSPQSJFUBSZBOE
QBUFOUFE$MBTT%UFDIOPMPHZ*UTGSFRVFODZ
SFTQPOTFJTMJNJUFEUPUIFSBOHFCFMPX)[*U
is not designed for driving midrange speakers or
tweeters. Every aspect of its operation has been
PQUJNJ[FEGPSMPXGSFRVFODZBNQMJGJDBUJPO
For detailed specifications, please refer to
Appendix B (page 15).
TYPICAL INSTALLATION SEQUENCE
The following represents the sequence for
a typical amplifier installation, using an
aftermarket source unit or OEM Interface
processor (like the CleanSweep® CL441dsp).
Additional steps and different procedures may
be required in some applications. If you have
BOZRVFTUJPOTQMFBTFDPOUBDUZPVSBVUIPSJ[FE
JL Audio dealer for assistance.
 %JTDPOOFDUUIFOFHBUJWFCBUUFSZQPTU
connection and secure the disconnected cable
to prevent accidental re-connection during
installation. This step is not optional!
2) Run power wire from the battery location to
the amplifier mounting location, taking care
to route it in such a way that it will not be
damaged and will not interfere with vehicle
operation. 2 AWG or larger is recommended
for wire runs greater than 72 inches (180
cm) in length. This 2 AWG wire needs
to be reduced to 4 AWG within 36 wire
inches of the amplifier using a distribution
block. Use a 1/0 AWG or 1/0 AWG main
power wire with a fused power distribution
block when additional amplifiers are being
installed with the 1200/1v3 and are being
powered from the same main power wire.
3) Connect power wire to the positive battery
post. Fuse the wire with an appropriate fuse
block (and connectors) within 18 inches (45
cm) wire length of the positive battery post.
This fuse is essential to protect the vehicle.
%POPUJOTUBMMUIFGVTFVOUJMUIFQPXFSXJSF
has been connected to the amplifier.
4) Run signal cables (RCA cables) and remote
turn-on wire from the source unit or interface
processor to the amplifier mounting location.
5) Run speaker wire from the speaker systems to
the amplifier mounting location.
6) Find a good, solid, bare metal grounding
point close to the amplifier and connect the
negative power wire to it using appropriate
hardware. Use minimum 4 AWG power wire,
no longer than 36 inches (90 cm). In some
vehicles, it may be necessary to upgrade the
battery’s ground wire as well. (See page 6 for
important notice).
7) Securely mount the amplifier using
appropriate hardware.
8) Connect the remote turn-on wire and the
positive and negative power wires to the
amplifier’s power connector plug. Then insert
the power connector plug into the amplifier’s
power connector receptacle, pushing firmly.
9) Connect the RCA input cables
to the amplifier.
10) Connect the speaker wires to the speaker
connector plug and insert the plug firmly into
the speaker connector receptacle.
11) Carefully review the amplifier’s control
settings to make sure that they are set
according to the needs of the system.
12) Install power wire fuse (100A for a
single 1200/1v3) and reconnect the negative
battery post terminal.
13) Turn on the source unit at a low level
to double-check that the amplifier is
configured correctly. Resist the temptation
to crank it up until you have verified the
control settings.
14) Make necessary adjustments to the input
sensitivity controls to obtain the right
overall output and the desired balance
in the system. See Appendix A (pages 14)
for the recommended input sensitivity
setting method.
15) Enjoy the fruits of your labor with your
favorite music.

Termékspecifikációk

Márka: JL Audio
Kategória: Vevő
Modell: Slash 1200/1v3

Szüksége van segítségre?

Ha segítségre van szüksége JL Audio Slash 1200/1v3, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók Vevő JL Audio

JL Audio

JL Audio VX600/6i Útmutató

12 Október 2024
JL Audio

JL Audio HD Series HD600/4 Útmutató

7 Október 2024
JL Audio

JL Audio Slash 300/4v3 Útmutató

28 Szeptember 2024
JL Audio

JL Audio MV700/5i Útmutató

19 Szeptember 2024
JL Audio

JL Audio XDM600/6 Útmutató

14 Szeptember 2024
JL Audio

JL Audio XDM800/8-24V Útmutató

2 Szeptember 2024
JL Audio

JL Audio XDM600/6-24V Útmutató

2 Szeptember 2024
JL Audio

JL Audio MHD600/4-24V Útmutató

27 Augusztus 2024
JL Audio

JL Audio MHD900/5-24V Útmutató

27 Augusztus 2024
JL Audio

JL Audio M800/8-24V Útmutató

27 Augusztus 2024

Útmutatók Vevő

Legújabb útmutatók Vevő

Yamaha

Yamaha Aventage RX-A4A Útmutató

9 Április 2025
Yamaha

Yamaha Aventage RX-A8A Útmutató

9 Április 2025
DJI

DJI D-RTK 3 Útmutató

5 Április 2025
Phonocar

Phonocar PH544 Útmutató

5 Április 2025
QSC

QSC SPA-Qf 60x2 Útmutató

2 Április 2025
Harper

Harper HDT2-5010 Útmutató

2 Április 2025
Harper

Harper HDT2-2010 Útmutató

2 Április 2025
Alpine

Alpine MRX-F65 Útmutató

31 Március 2025
Streacom

Streacom TL1 Útmutató

31 Március 2025
Pro-Ject

Pro-Ject Stereo Box DS Útmutató

30 Március 2025