Használati útmutató Jensen PCD163

Jensen nincs kategorizálva PCD163

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Jensen PCD163 (46 oldal) a nincs kategorizálva kategóriában. Ezt az útmutatót 2 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/46
PCD163
Owner's Manual/Manual del Usario/Manual de L'Utilisateur
AM/FM/CD Receiver
Receptor AM/FM/CD
AM/FM/CD Ampli-Syntoniseur
RPT
TRACK
SCN
LOUD
AUX IN
DISP
MODE
BAND
T
U
N
I
N
G
MUTE
PCD163
SEL/MENU
PCD163
2
PREPARATION
Getting Started
It’s a good idea to read all of the instructions
before beginning the installation.
Contents
Installation Instructions.............................. 3
Wiring ........................................................ 5
Operating Instructions ............................... 6
CD Player Operating Instructions............ 10
Care and Maintenance............................ 12
Specifications .......................................... 13
Installation Requirements
This unit is designed for installation in cars,
trucks, and vans with an existing radio opening.
In many cases, a special installation kit will be
required to mount the radio to the dashboard.
These kits are available at electronics supply
stores and car stereo specialty shops. Always
check the kit application before purchasing to
make sure the kit works with your vehicle. If you
need a kit but cannot locate one, call our
customer support line at 1-800-323-4815.
(U.S.A. and Canada only.)
Tools and Supplies
The following tools and supplies are needed to
install the radio.
• Torx type, flathead and Philips
screwdrivers
• Wire cutters and strippers
• Tools to remove existing radio
(screwdriver, socket wrench set or other
tools)
• Electrical tape
• Crimping tool
• Volt meter/test light
• Crimp connections
• 18 gauge wire for power connections
• 16-18 gauge speaker wire
Speaker Requirements
Only connect speakers rated with a load
impedance of 4 ohms. Speakers with a load
impedance of less than 4 ohms could damage
the unit.
Disconnect Battery
Before you begin, disconnect the battery
negative terminal.
Toll-Free Installation Assistance
If you require assistance, contact Technical
Support at 1-800-323-4815 from 8:30 a.m. to
7:00 p.m. EST Monday through Friday and from
9:00 a.m. to 5:00 p.m. EST on Saturday.
(U.S.A. and Canada only.)
Pour des instructions en Francais, référez-vous à la page 30.
Para obtener instrucciones en Español, diríjase a la página 16.
PCD163
3
INSTALLATION INSTRUCTIONS
Installation Using the Mounting
Sleeve
1. Slide the mounting sleeve off the chassis.
If it is locked into position, use the removal
tools (supplied) to disengage it.
2. Check the dashboard opening size by
sliding the mounting sleeve into it. If the
opening is too small, carefully cut or file as
necessary until the sleeve easily slides
into the opening. Do not force the sleeve
into the opening or cause it to bend or
bow. Check for sufficient space behind the
dashboard for the radio chassis.
3. Locate the series of bend tabs along the
top, bottom, and sides of the mounting
sleeve. With the sleeve fully inserted into
the dashboard opening, bend as many of
the tabs outward as necessary to firmly
secure the sleeve to the dashboard.
4. Place the radio in front of the dashboard
opening so the wiring can be brought
through the mounting sleeve. Follow the
wiring diagram carefully and make certain
all connections are secure and insulated
with wire nuts or electrical tape. After
completing the wiring connections, turn
the unit on to confirm operation (vehicle
ignition must be “on”). If the unit does not
operate, re-check all wiring until the
problem is corrected.
5. Make sure the radio is right-side up, then
carefully slide the radio into the mounting
sleeve until it is fully seated and the spring
clips lock it into place.
6. Attach one end of the perforated support
strap (supplied) to the screw stud on the
rear of the chassis using the hex nut
provided. Fasten the other end of the
perforated strap to a secure part of the
dashboard either above or below the radio
using the screw provided. Bend the strap
to position it as necessary.
7. Test the radio using the Operating
Instructions that follow.
RPT
TRACK
SCN
LOUD
AUX IN
D PIS
MODE
BAND
T
U
N
I
N
G
MUTE
PCD163
SEL/M ENU
CAUTION: The support strap
must be used to prevent
damage to the dashboard from
the weight of the radio or
improper operation due to
vibration.
CAUTION: For proper operation
of the CD player, the chassis
must be mounted within 20° of
horizontal. Make sure the unit is
mounted within this limitation.
INSTALLATION
BEND TABS

Termékspecifikációk

Márka: Jensen
Kategória: nincs kategorizálva
Modell: PCD163

Szüksége van segítségre?

Ha segítségre van szüksége Jensen PCD163, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók nincs kategorizálva Jensen

Jensen

Jensen CAR701-4 Útmutató

8 Január 2025
Jensen

Jensen MP5620SE Útmutató

9 Október 2024
Jensen

Jensen BUCAM300J Útmutató

29 Szeptember 2024
Jensen

Jensen VM9114 Útmutató

21 Szeptember 2024
Jensen

Jensen MP1516BT Útmutató

20 Szeptember 2024
Jensen

Jensen CD1211 Útmutató

18 Szeptember 2024
Jensen

Jensen JTV1917DVDC Útmutató

18 Szeptember 2024
Jensen

Jensen VM9126 Útmutató

8 Szeptember 2024
Jensen

Jensen JC7DM Útmutató

26 Augusztus 2024
Jensen

Jensen CD4720 Útmutató

11 Augusztus 2024

Útmutatók nincs kategorizálva

Legújabb útmutatók nincs kategorizálva

Panasonic

Panasonic CY-EM100N Útmutató

4 Április 2025
Panasonic

Panasonic CQ-DF602W Útmutató

4 Április 2025
Panasonic

Panasonic CQ-DF203W Útmutató

4 Április 2025
Panasonic

Panasonic SL-PR300 Útmutató

4 Április 2025
Panasonic

Panasonic SL-1210MK5 Útmutató

4 Április 2025
Panasonic

Panasonic SH-FX60 Útmutató

4 Április 2025
Sony

Sony BRC-HSD1 Útmutató

4 Április 2025
Sony

Sony BRBK-MF1 Útmutató

4 Április 2025
Sony

Sony HKCU-FP2 Útmutató

4 Április 2025
Sony

Sony HKC-P3300 Útmutató

4 Április 2025