Használati útmutató IFM IM002A

IFM nincs kategorizálva IM002A

Olvassa el alább 📖 a magyar nyelvű használati útmutatót IFM IM002A (3 oldal) a nincs kategorizálva kategóriában. Ezt az útmutatót 3 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF

Oldal 1/3

Operating instructions

(Ex protection related part)

Inductive sensors

IM5**A / IM0**A

80297015 / 00 09 / 2020

Remarks for safe use in hazardous areas

Functions and features

• Use in hazardous areas according to the classification

II 3D

(group II, category 3D, apparatus for dust atmosphere).

Complies with the requirements of the standards EN 60079-0 and EN 60079-31.

• Certificat d‘examen de type:

BVS 20 ATEX E 056 X

• Certificat d‘examen IECEx de type:

IECEx BVS 20.0043X

• Marking

II 3D Ex tc IIIC T95°C Dc X

• Permissible operating temperature of the application (proper usage):

Ta: -20°C...+60°C

Installation / Set-up

The units must only be installed, connected and set up by qualified staff. The qualified staff

must have knowledge of protection classes, regulations and provisions for apparatus in

hazardous areas.

Check whether the classification (see “Marking” above and marking on the unit) is suitable

for the application.

Installation remarks / Installation

• Adhere to the relevant national regulations and provisions.

• The relevant installation regulations must be adhered to. In particular, take into account the

requirements relating to the temperature limitation as regards the expected dust deposits.

• Avoid electrostatic charging on housings and cables.

• To avoid electrostatic charging steps must be taken to ensure the equalisation of potential

of metal parts (plug housing, fixing elements, etc.).

• Protect the units and the cables efficiently against damage.

• To avoid soiling, do not remove the dust caps from the cable glands or the plugs until

introducing the cables or attaching the socket.

• If the sensing direction is altered, ensure that the locking screw is securely tightened.

• When the terminal chamber is closed, ensure that the securing element is correctly locked

in and is flush with the housing.

• When replacing the cable gland, ensure a tight fit of the cable gland as well as the cover

plug.

• It is the responsibility of the user to determine the appropriate tightening torques for the

type of cable used. The cable glands and the cap nut have to be firmly tightened. If the

connection thread or the cap nut is overtightened or undertightened, the type of protection,

the tightness and the strain relief are impaired.

• Maintenance intervals are application-specific and therefore need to be defined by the

operator depending on the operating conditions.

• During maintenance, especially those parts on which the type of protection depends need

to be examined (e.g. integrity of the components of the cable gland, of the seals).

Special conditions for safe operation

• For units with terminal chamber (cable gland) and cable units a sufficient strain relief must

be ensured or the cable must be firmly laid.

• Use ifm sockets EVC**A with Ex certificate (certificate number BVS 08 ATEX E 109 U).

• Secure the sockets by tightening the hexagon coupling nut sufficiently according to the

requirements of the Ex protection related part of the operating instructions of the socket.

• Do not separate the connector when energized.

• Apply a durable warning in suitable form close to the connector reading: “Do not separate

when energized” or use the enclosed label if you can ensure a durable marking.

• Do not disconnect the cables from units with terminal chamber while live.

• The housing and housing parts made of plastic were tested in accordance with

EN 60079-0 for group II and for a low mechanical risk with an impact energy of 4 joules.

• Avoid direct radiation with high UV components (sunlight). Mount the unit in a protected

place.

• Where units require an additional fuse, this must be located outside the hazardous areas.

Maintenance / repair

The unit must not be modified nor can it be repaired. In case of a fault please contact the

manufacturer.

Data sheets, EC declaration of conformity and EC type test certificates are available from

the manufacturer on request.

Termékspecifikációk

Márka:	IFM
Kategória:	nincs kategorizálva
Modell:	IM002A

Szüksége van segítségre?

Ha segítségre van szüksége IFM IM002A, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek

Az Ön neve*

Az Ön e-mail címe*

Írja ide kérdését

Útmutatók nincs kategorizálva IFM

23 Március 2025

23 Március 2025

18 Március 2025

18 Március 2025

18 Március 2025

18 Március 2025

16 Január 2025

16 Január 2025

16 Január 2025

14 Január 2025

Útmutatók nincs kategorizálva

Legújabb útmutatók nincs kategorizálva

CyberPower BPSE72V40ART2U Útmutató

31 Március 2025

Spin Master 6026397 Útmutató

31 Március 2025

Evga XC3 Útmutató

31 Március 2025

InLine 61602C Útmutató

31 Március 2025

American DJ Ultra HEX Bar 12 Útmutató

31 Március 2025

TomTom GO Camper Tour (2nd Generation) Útmutató

31 Március 2025

Shure WA555 Útmutató

30 Március 2025

Einhell ESS 9000-T Útmutató

30 Március 2025

Einhell AV 10 Útmutató

30 Március 2025

American DJ POW-R Bar Rack USB Útmutató

30 Március 2025