Használati útmutató Hoover HECH916/4X

Hoover Páraelszívó HECH916/4X

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Hoover HECH916/4X (26 oldal) a Páraelszívó kategóriában. Ezt az útmutatót 4 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/26
تﺎﻤﯿﻠﻌﺘﻟا ﻞﯿﻟدماﺪﺨﺘﺳﻻ ﺔﻨﺧﺪﻤﻟا
INSTRUCTION MANUAL FOR CHIMNEY HOODS
HOTTE GUIDE D’UTILISATION
1
EN
SCOPE OF INSTRUCTION MANUΑL
Dear Customer,
In the sections provided herein, there is necessary information which will enable you to use the
device efficiently and safely. Please, read these instructions carefully before installation of the
device
Section 1 Important points which must be observed before using the chimney
Section 2 Technical specifications of the chimney hood.
Section 3 Technical dimensions of the chimney hood
Section 4 Electrical diagram of the chimney hood.
Section 5 Information about installation connection of the chimney hood.
Section 6 Information about use the chimney hoodof .
Section 7 Information about maintenance of the chimney hood.
THE DEVICE PRODUCED EARTHED. IS AS
DO NOT USE IT WITH UNEARTHED PLUG.
IMPORTANT PRECAUTIONS AND POINTS WHICH MUST BE OBSERVED
Section 1
1. and be done byThe electrical installation connections must the service staff who well-is
informed the subjectof ;
2. The operating voltage is 220 240 Volts. Do not operate the device in lower or higher–
voltage.
3. Do not connect to the chimneys where the heating stove is connected, to the gas flue or to
the chimneys where the fire rises.
4. Plug the product into the socket where there is an earthed connection.
5. Fire catching food should not be cooked under the device.
6. Do not use other materials instead of aluminum filter in the device.
7. Do not plug into the socket without completion of the installation of the device.
8. Do not run the device without aluminum filter.
9. Do not touch the bulb of the device when it is left on for a long time..
2
EN
10. Do not remove the aluminum filter when the device is running.
11. Do not turn off the device directly by plugging it out when it is running. Turn off fromit
control panel.
12. The device should be cleaned periodically..
13. The height between the lower surface of the chimney hood and oven must be 65 cm for
electrical ovens, and 75 cm for gas-fired or mix ovens
14. Keep the packaging material away from the children because they may be dangerous for
them.
15. Run the chimney hood after the kettle or frying pan is put on the oven.
16. Run the chimney hood for 15 minutes more after the operation of cooking or frying is
finished in order to clean the air of the kitchen off the smell and vapor which appeared
during cooking..
17. Let some fresh air into environment when the chimney hood is running, especially, when it
is used in the same time with the gas-fired ovens.
18. Contact the nearest service if your device is failed to run with any reason.
19. Our Company may not be held responsible from the failures arising from use which is not
consistent with the cautions stated above.
TECHNICAL SPECIFICATIONS
Section 2
1. Chimney
2. Control panel
3. Body of the chimney hood
4. Aluminum filter
5. Illumination lamp
6. Glass
3
EN
TECHNICAL SPECIFICATIONS OF THE CHIMNEY HOOD
LENGTH -900 mm600
WIDTH 475 mm
HEIGHT Min. 706 mm Max 980
mm
CONTROLLER PUSH BUTTON
AIR SUCTION m3400
BULB POWER x2 W1
MOTOR POWER 190W
TOTAL POWER W192
DIAMETER OF AIR OUTLET
PIPE
120 mm
SUPPLY VOLTAGE 240 V 50Hz 220 –
TECHNICAL DIMENSIONS
Section 3
Note: All dimensions are in mm.
HECH616/4X
HECH916/4X
4
EN
ELECTRICAL CONNECTION DIAGRAM
Section 4
Digital Touch Button Push Button
LCD Screen
5
EN
INSTALLATION DIAGRAM
Section 5
1. Draw a straight line by a measuring stick starting from the surface of the oven to 700+280:
990 mm if you want to save a space of 700 mm between the oven and the lower surface of
the chimney hood. Align the drawn line to the right and left edges. Draw a 67,5 mm axis line
from aligned center to every two sides. Make a hole by 6 mm diameter electrical drill
through two drawn points. Penetrate the expansion bolt and install the hangers.
2. Doing installation of secondary chimney of the chimney hood: draw 75 mm line from the top
surface towards the lower section. Make sure that the line is equal to right and left parts.
Draw 50 mm line each at both sides of the line and, then, make a hole through these two
lines. Penetrate an 8 mm diameter expansion bolt and tighten until 2 mm space is left in-
between of a 2,5 diameter slat screw and the expansion bolt. Later, the product is mounted
on its place and the installation will be completed by installing the inner chimney.
The operation order:
1st operation: Installation hanger of
2nd operation: Installation of chimney connection metal sheet
3rd
operation: Hanging the chimney hood
4th operation: Installation of lower chimney of the chimney hood
5th operation: Installation of inner chimney
6th operation: Making electrical connection
INSTALLATION :
6
EN
INFORMATION ABOUT USE OF THE CHIMNEY HOOD
Section 6-1
LCD-Switch Chimney Hood Control Card Features
A
ON-OFF BUTTON
B
MINUS BUTTON
C
PLUS BUTTON
D
TIMER BUTTON
E
BULB BUTTON
F
ALARM BUTTON
On/Off Button: used to start and stop the motor. In the beginning, the motor runs in 2
nd
cycle. The number of cycle is represented by bar levels and the rotation speed of the fan shown at
the left-side of the display.
Minus Button: the cycle of motor reduces until it reaches 1
st cycle each time when it is pushed
if the motor is running. In addition, it is used to reduce the timer value. On the display, it is
represented by the number of bars and the number of rotation of the fan.
Plus Button: used to increase the cycle of motor each time when it is pushed until it
reaches the highest cycle level if the motor is running. In addition, it is used to reduce the timer
value. On the display, it is represented by the number of bars and the number of rotation of the
fan.
Shutdown Timer Button: a 15 minute starting timer value will be displayed and the clock icon
will flash for 5 times when this button is pushed while the motor is running. The clock icon will
be displayed until the timer value lapses. The motor will stop and the bulb will turn off, if it is on,
when the timer lapsed.
Alarm Timer Button: a 5 minute alarm timer will be displayed as starting timer on the
display and the bell icon will flash for 5 times when this button is pushed independent of whether or
not the motor is running. The bell icon will be displayed on the display until the timer time lapses.
The buzzer will ring for 20 seconds and the bell icon will flash when the timer lapsed. The buzzer
can be shut by pushing the alarm timer when it is ringing.
Being valid for both of them; the timer value can be adjusted to any value in-between of 1 minute
and 9 hour 59 minutes by pushing MINUS or PLUS buttons while flashing. The timer value will
increase or decrease very quickly when the MINUS or PLUS buttons are held pushed. The current
value of the timer will be displayed on the display when the timer button is pushed while the timer
is set. The started timer button is pushed one more time and it will be reduced until the timer
becomes zero by pushing MINUS button if the started timer is needed to be cancelled.
8
EN
0 : Stop the engine
1 : Powering the first level
2 : Powering the second level
3 : Powering the third level
: On and off button of lamp
Section 6-3
INFORMATION ABOUT USE OF TOUCH-OPERATED SWITCH
A
ON OFF BUTTON–
B
MINUS BUTTON
C
DIGITAL DISPLAY
D
PLUS BUTTON
E
TIMER BUTTON
F
BULB BUTTON
A – On/Off Button: used to start and stop the motor. The motor starts running in 2
nd cycle
when On-Off button is pushed for the first time.
B – Minus Button: reduces the cycle of the motor.
C – Digital Display: shows in which cycle the motor is.
D – Plus Button: used to increase the cycle of the motor with one level.
E – Timer Button: when this button is pushed, the cycle of the motor flashes on digital display
and the motor stops within 15 minutes. It is necessary to keep pushed this button for 3 seconds
to activate it. Push only one time to cancel it.
F – Bulb Button: used to turn on and off the bulb.
11
FR
Chers Utilisateurs,
Nous vous remercions pour votre choix de produit. Afin de pouvoir utiliser votre hotte en sécurité et
de manière efficace pour une longue durée, le bon montage de ce dernier est indispensable, nous
vous conseillons de lire attentiveme nt le mode d’emploi avant son utilisation.
1) PROCEDURE A SUIVRE AVANT L’UTILISATION
1. Brancher votre hotte sur une prise de terre 220 V « LE FOURNISSERUR NE SERA EN AUCUN
CAS RESPONSABLE SI DES DEFAILLANCES SE PRESENTES EN RAISON D’UNE
MAUVAISE UTILISATION »
2. Prévoyez la sortie de la hotte au tuyau de cheminée, comme pour la connexion de la chaudière, et
le chauffe-eau.
3. Assurez vous que les boutons sur le panneau de la hotte soit en position fermée avant le
branchement de ce dernier.
4. Placer l’ampoule en ouvrant le boitier à filtre en aluminium placé sous la hotte
5. Effectuer le montage de votre hotte à l’aide du schéma fournit dans l’emballage.
6. La distance préconisée entre la plaque à trou (filtre) de votre hotte et de votre gazinière doit être
au minimum 75 cm et 65 cm pour les fours électriques.
7. Votre hotte a été conçue de manière à l’utiliser avec ou sans connexion de tuyau pour cheminée.
1) UTILISATION AVEC TUYAU DE CHEMINEE
Sur votre hotte se trouve une sortie d’air. Les trous de sortie d’air sont de 12 cm de diamètre et sont
connectés au tuyau de cheminée à l’aide d’un tuyau en aluminium. Les précautions doivent être
prises pour les tuyaux verticaux afin d’éviter l’entrée d’eau de pluie. Dans le cas d’une défaillance
due à cette raison, la garantie de votre hotte ne sera pas valable. A cet égard, il est recommandé
d’utiliser un tuyau d’un diamètre de 120mm. Plus votre tuyau sera court et sans angle, plus votre
hotte sera efficace.
2) UTILISATION SANS TUYAU DE CHEMINEE
Important: Si toutefois l’utilisation se fait sans tuyau de cheminée vous pouvez vous procurer un
filtre en carbone auprès de nos services compétents.
Vous pouvez remplacer le filtre par le FİLTRE EN CARBONE délivré par le service en retirant le
boitier à filtre en appuyant sur les poignées. Votre hotte est donc prête à fonctionner.

Termékspecifikációk

Márka: Hoover
Kategória: Páraelszívó
Modell: HECH916/4X

Szüksége van segítségre?

Ha segítségre van szüksége Hoover HECH916/4X, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók Páraelszívó Hoover

Hoover

Hoover HDTI6500/1X Útmutató

12 Január 2025
Hoover

Hoover HSD6SG Útmutató

11 December 2024
Hoover

Hoover HBT6RX Útmutató

11 December 2024
Hoover

Hoover HVE 93 X Útmutató

29 Szeptember 2024
Hoover

Hoover HDP620IN Útmutató

27 Szeptember 2024
Hoover

Hoover HTM 656 WTK Útmutató

22 Szeptember 2024
Hoover

Hoover HDM656BTK Útmutató

4 Szeptember 2024
Hoover

Hoover HV-C60RS Útmutató

3 Szeptember 2024
Hoover

Hoover HV-C90RU Útmutató

3 Szeptember 2024
Hoover

Hoover HPY6SGTK Útmutató

3 Szeptember 2024

Útmutatók Páraelszívó

Legújabb útmutatók Páraelszívó

Atag

Atag WS 6011 IM Útmutató

10 Április 2025
Bosch

Bosch DWB091E59 Útmutató

10 Április 2025
Smeg

Smeg CA6SHRX Útmutató

10 Április 2025
Faber

Faber Glove Útmutató

10 Április 2025
Novy

Novy 7220 Útmutató

10 Április 2025
Novy

Novy 7050 Útmutató

10 Április 2025
CATA

CATA C GLAS H Útmutató

10 Április 2025
Novy

Novy 7841 Útmutató

10 Április 2025
Bauknecht

Bauknecht d 641 Útmutató

9 Április 2025
Bosch

Bosch DEM63AC00 Útmutató

9 Április 2025