Használati útmutató Hobbywing QuicRun 10BL60

Hobbywing Rádióvezérlésű játékok QuicRun 10BL60

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Hobbywing QuicRun 10BL60 (1 oldal) a Rádióvezérlésű játékok kategóriában. Ezt az útmutatót 3 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF

Oldal 1/1

Form 1: Parameter List of QuicRun-WP16BL30 and QuicRun-WP10BL60:

(Italics in the form below indicate factory defaults) Form 2: Parameter List of QuicRun-WP-8BL150

(Italics in the form below indicate factory defaults)

Option 1

1.Running Mode

2.Drag Brake Force

3. Low Voltage Cutoff

4. Start Mode (Punch)

5. Max. Brake Force

6. Max. Reverse Force

7. Initial Brake Force

8. Throttle Range

9. Timing

Option 2 Option 3 Option 4 Option 5 Option 6 Option 7 Option 8 Option 9

Fwd/Br

0% 5% 10% 20% 40% 60%

Disable 2.6V/Cell 2.8V/Cell 3.2V/Cell 3.4V/Cell3.0V/Cell

80% 100%

Fwd/Rev/Br Fwd/Rev

Level 5 Level 6 Level 7 Level 8 Level 9Level 4Level 3Level 2

Level 1

25% 50% 100% Disable 75%

25%

drag brake

force

drag brake

force

50% 75% 100%

0% 20% 40%

(Narrow)

(Normal)

12%(Wide)

0.00 deg 3.75 deg 7.50 deg 15.00 deg 18.75 deg 22.50 deg 26.25 deg11.25 deg

Enable Disable

CCW CW

Note 2

Auto-

identification 2S LiPo 3S LiPo 4S LiPo 5S LiPo 6S LiPo

Programmable Items

Note 1

Option 1

1.Running Mode

2.Drag Brake Force

3. Low Voltage Cutoff

4. Start Mode (Punch)

5. Max. Brake Force

6. Max. Reverse Force

7. Initial Brake Force

8. Throttle Range

9. Timing

Option 2 Option 3 Option 4 Option 5 Option 6 Option 7 Option 8 Option 9

Fwd/Br

0% 5% 10% 20% 40% 60%

Disable 2.6V/Cell 2.8V/Cell 3.2V/Cell 3.4V/Cell3.0V/Cell

80% 100%

Fwd/Rev/Br Fwd/Rev

Level 5 Level 6 Level 7 Level 8 Level 9Level 4Level 3Level 2

Level 1

25% 50% 75% 100% Disable

25% 50% 75% 100%

0% 20% 40%

(Narrow) 12%(Wide)

0.00 deg 3.75 deg 7.50 deg 15.00 deg 18.75 deg 22.50 deg 26.25 deg11.25 deg

10. Overheat

Protection

11. Motor Rotation

12.Cell Count

Programmable Items

Note 1

Note 1: Fwd=Forward, Rev=Reverse, Brk=Brake

Note 2: When set to the “Auto-identification” mode, the battery pack can only be identified as 2S, 4S and 6S Lipo. Because the

normal voltage of each LiPo cell varies from 2.6V to 4.2V, it’s not easy to correctly calculate the cell count of a discharged LiPo

battery pack. Therefore, we strongly suggest you set the “LiPo Cells” manually.

In order to make sure the ESC fits the throttle range of your transmitter, you must calibrate it when begin to use a new ESC, or a used transmitter if some of its settings have been changed,

like the Throttle Trim, D/R, EPA or other parameters. Otherwise, the ESC cannot work properly. Besides, we strongly recommend users to enable the “failsafe” function of the transmitter, set

the “F/S” of the throttle channel to the Shutdown mode or set the protection value to the neutral position, so the car can be stopped if the receiver fails to get the radio signals from the

transmitter. Please calibrate the throttle range according to the following steps.

Model QuicRun-WP-16BL30 QuicRun-WP-10BL60

Continuous Current /

Peak Current / Resistance

Motor Type Supported

Car Applicable

30A/180A/0.002Ω

Sensorless Brushless Motor (compatible with sensored motor but not in sensored operating mode）

1:18 & 1:16 On-road / Off-road / Buggy / Monster 1:10 On-road / Off-road / Buggy / Monster

60A/360A/0.001Ω

6V/3A (Switch Mode)

Motor Limit

Battery 4-9 Cells NiMH, 2-3S Lipo 4-9 Cells NiMH, 2-3S Lipo

QuicRun-WP-8BL150

1:8 Buggy / Monster

150A/950A/0.00035Ω

6V/3A (Switch Mode)

9-18 Cells NiMH, 3-6S Lipo

BEC Output

Dimensions / Weight

External Program Port

Working voltage of Fan

36x28x16mm / 38g

Not Available

No cooling fan

48.5x38x32mm / 90g

Available

From BEC(6V)

59.5x48x42mm / 178g

Available

From BEC(6V)

6V/1A (Linear Mode)

For 2S Lipo or 6 cells NiMH:

1. On-road:

2435-size or smaller motor with the KV<8000

2. Off-road / Buggy / Monster:

2435-size or smaller motor with the KV<5000

For 3S Lipo or 9 cells NiMH:

1. On-road:

2435-size or smaller motor with the KV<5500

2. Off-road / Buggy / Monster:

2435-size or smaller motor with the KV<3500.

For 2S Lipo or 6 cells NiMH:

1. On-road:

3656-size or smaller motor with the KV<6000

2. Off-road / Buggy / Monster:

3656-size or smaller motor with the KV<4000

For 3S Lipo or 9 cells NiMH:

1. On-road:

3656-size or smaller motor with the KV<4000

2. Off-road / Buggy / Monster:

3656-size or smaller motor with the KV<3000.

For 4S Lipo or 12 cells NiMH:

4274-size or smaller motor with the KV<3000

For 6S Lipo or 18 cells NiMH:

4274-size or smaller motor with the KV<2400

• Water-proof and dust-proof for all-weather races;

(Note: please uninstall the cooling fan before using this ESC in water; Clean and dry it soon after the

use for avoiding the connectors get rusty.)

• External programming port, easy to connect to the Program Card when setting the ESC;

• Proportional brake with 4 steps of maximum brake force adjustment and 8 steps of drag brake force adjustment;

• 9 steps of acceleration(punch) adjustment from “soft” to “Very aggressive” to fit for different kinds

of models, tires and tracks;

• Multiple protections: Low voltage cut-off protection / Over-heat protection / Throttle signal loss

protection / Motor lock-up protection;

• One-button(the “SET” button on the ESC) to set the ESC, and easy to reset all parameters to the

factory default settings;

• Compatible with the optional device-the portable Digital LED Program Card, especially convenient

for outdoor use.

Features

Begin to Use a New Brushless ESC

Program the ESC

Connections

Specifications

IMPORT ANT

CA UT IONS

AT T ENT ION

Congratulations and thanks for purchasing HOBBYWING electronic speed controller

(ESC). The brushless power system for RC model can be very powerful and dangerous,

so please read this manual carefully. Since we have no control over the installation,

application, use or maintenance of this product, in no case shall we be liable for any

damages, losses or costs. Besides, we have the rights to change the design,

appearance, functions and operational requirements without any notifications.

AT T ENT ION

Program the ESC with the SET Button

Set the ESC by the Program Card

Set up Throttle Range

• In the programming process, the motor will emit “Beep” tone while the LED is

flashing.

• If the “N” is bigger than the number “5”, we use a long time flash and long

“Beep—” tone to represent “5”, so it is easy to identify the items of the big

number.

For example, if the LED flashes as the following:

“A long time flash + 1 short time flash” (Motor sounds “B—B”) = the No. 6 item

“A long time flash + 2 short time flash” (Motor sounds “B—BB”) = the No. 7 item

“A long time flash + 3 short time flash” (Motor sounds “B—BBB”) = the No. 8 item,

and so on.

The Program Card is optional equipment which

needs to be purchased separately. It has 3 digital

LEDs to display the programmable items’ number

and the options’ number.

(Please refer to the user manual of the program card

for detail info)

AT T ENT ION

The QuicRun-WP10BL60 and QuicRun-WP8BL150 can only be connected to the

program card via the external programming port.

AT T ENT ION

a) When the throttle stick is in the neutral range, neither the Red LED nor the Green LED lights up;

b) When the car moves forward, the Red LED solidly lights; the Green LED also lights up when the throttle stick is at the top position (100% throttle);

c) When the car brakes, the Red LED solidly lights; the Green LED also lights up when the throttle stick is at the bottom position and the maximum brake force is set to 100%;

d) When the car reverses, the Red LED solidly lights; the Green LED also lights up when the throttle stick is at the bottom position and the maximum reverse force is set to 100%.

Check the LED Status in Normal Running

Explanation for the Beep Sound

In normal case, when the ESC is switched on, the motor will emit several “Beep” tones to express the cell count of the battery pack. For example, “Beep-Beep-” means 2S LiPo,

“Beep-Beep-Beep-” means 3S LiPo, “Beep-Beep-Beep- Beep-” means 4S LiPo.

EXPLA NAT ION

Trouble Shooting

Trouble(s) Solution(s)Possible Causes

No battery voltage is input to the ESC. The switch of the ESC is damaged

The voltage of the battery pack is not in the normal range,

it’s too high or too low.

The throttle signal wire is oppositely inserted or into the incorrect channel.

The wire connections between the ESC and the motor need to be changed.

Low voltage cutoff protection (Red LED blinks)

Overheat protection (Green LED blinks)

The throttle neutral point drifts to the brake area.

The connections between motor and ESC are not reliable.

The ESC is damaged.

Check the connections between the battery and the ESC, re-solder the connectors if needed.

Change the switch.

Check the voltage of the battery pack.

Plug the signal wire (Rx lead) correctly into the throttle channel (usually Channel #2) of the receiver.

Swap any two wire connections between the ESC and the motor.

Check the battery voltage. If still has some capacity, lower the cut-off threshold voltage;

if not, replace a new battery.

Wait several minutes to cool the ESC. Increase the gear ratio or the T number (Turns) of the motor.

Calibrate the throttle neutral point again to ensure that no LED lights when the throttle stick is

at the neutral position.

Check all the solder joints and ensure they are well soldered. Check connectors.

Contact the distributor for after-sales service.

After power on, motor doesn’t work but emits “beep-beep-, beep-beep-”

alert tone. (there’s 1 second pause between 2 “beep-beep-”).

After power on, the Red LED turns solid red but the motor doesn’t work.

Turn on the switch, no LED lights up, and neither the motor nor fan works.

The car runs backwards when accelerating forward on radio.

The motor stutters, and cannot start up.

The vehicle can go forward but cannot reverse.

The car suddenly slows down, then stops about 15 seconds later.

Enter the 2nd item

"Drag Brake Force"

Hold the SET key

Switch on the ESC

Red LED flashes

Green LED flashes

once

Green LED flashes

twice

Green LED flashes

3 times

Green LED flashes

N times

Release

SET kye

Release

SET kye

Press

SET kye

Press

SET kye

Press

SET kye

Press

SET kye

Release

SET kye

Release

SET kye

Red LED flashes once, choose "0%"

Red LED flashes twice, choose "5%"

Red LED flashes 3 times, choose "10%"

Red LED flashes 4 times, choose "20%"

Red LED flashes 5 times, choose "40%"

Red LED flashes 6 times, choose "60%"

Red LED flashes 7 times, choose "80%"

Red LED flashes 8 times, choose "100%"

Red LED flashes once, choose "None"

Red LED flashes twice, choose "2.6V"

Red LED flashes 3 times, choose "2.8V"

Red LED flashes 4 times, choose "3.0V"

Red LED flashes 5 times, choose "3.2V"

Red LED flashes 6 times, choose "3.4V"

Red LED flashes once to choose

Red LED flashes twice to choose

Red LED flashes 3 times to choose

"Forward with brake"

"Forward / Reverse with brake"

"Forward / Reverse"

Enter the 3rd

item"Low Voltage

Cut-Off"

Enter the N

th item

Enter the 1st item

"Running Mode"

Tur n off the ESC

Tur n on the transmitter

Hold SET key for 3 seconds

......The following steps are just like the above setps......

Finish programming, switch off the ESC, and then switch it on

Programmable Items

1. Running Mode: With “Forward with Brake” mode, the car can go forward and brake, but cannot go backward, this mode is suitable for competition; “Forward / Reverse with Brake” mode provides backward function, which is suitable for daily training.

Note: “Forward/Reverse with Brake” mode uses “Double-click” method to make the car go backward. When you move the throttle stick from forward zone to backward zone for the first time (The 1st “click”), the ESC begins to brake the motor,

the motor speeds down but it is still running, not completely stopped, so the backward action is NOT happened immediately. When the throttle stick is moved to the backward zone again (The 2nd “click”), if the motor speed is slowed down to

zero, then the backward action will happen. The “Double-Click” method can prevent mistakenly reversing action when the brake function is frequently used in steering. By the way, in the process of braking or reversing, if the throttle stick is

moved to forward zone, the motor will run forward at once. “Forward/Reverse” mode uses “single-click” method to make the car reverse. When moving the throttle stick from neutral zone to backward zone, the vehicle reverses immediately,

so this mode is usually used in rock crawling.

2. Set the amount of drag brake applied at neutral throttle to simulate the slight braking effect of a neutral brushed motor while coasting.Drag Brake Force:

3. Low Voltage Cut-Off: The function mainly prevents the Lipo battery from over discharging. The ESC detects the battery voltage at any time, if the voltage is lower than the threshold for 2 seconds, the output power will be reduced 70%,

after 15 seconds the output power will be completely shut off and the red LED flashes in such a way: “ -, -, -”. Please stop your car at the track side as soon as possible to avoid obstructing other racing cars.☆☆☆

Note: For NiMH battery, if the voltage of the whole NiMH battery pack is higher than 9.0V, it will be considered as a 3 cells Lipo battery pack; If it is lower than 9.0V, it will be considered as a 2 cells Lipo battery pack. For example, if a NiMH battery

pack is 8.0V, and the threshold is set to 2.6V/Cell, so it will be considered as a 2 cells Lipo battery pack, and the low-voltage cut-off threshold for this NiMH battery pack is 2.6x2=5.2V.

4. Start Mode (Also called “Punch” or “Acceleration”): Level 1 has very soft start acceleration, while level 9 has very quick start acceleration. From Level 1 to Level 9, the start force is increasing. If you choose “Level 7” to “Level 9”, you should use good

quality battery with powerful discharge ability, otherwise you cannot get the burst start effect as you want. If the motor cannot run smoothly (the motor is cogging), sometimes it is caused by the weak discharge ability, please use a better

battery or increase the gear ratio.

5. The ESC provides proportional brake function. The brake force is related to the position of the throttle stick. Maximum brake force refers to the force when the throttle stick is located at the top point of the backward Maximum Brake Force:

zone. A very large brake force can shorten the brake time, but it may damage the gears.

6. Sets how much power will be applied in the reverse direction.Maximum Reverse Force:

7. Initial Brake Force: It is also called “minimum brake force”, which refers to the force when the throttle stick is located at the initial position of the backward zone. The default value is equal to the drag brake force, so the brake action can be very smoothly.

8. This setting adjusts the width of the neutral range.Throttle Neutral Range:

9. This function can be used to fine-tune the output power of the motor, the bigger the timing, the faster the motor runs or the larger output power of the motor. As the Boost Timing technology has been introduced into this ESC, so Timing:

under the sensored mode, adjust the ESC timing can greatly increase the motor RPM. Therefore, please remember to enlarge the gear ratio of the chassis and carefully check temperatures of the motor and the ESC after increasing the timing.

10. If this function is activated, the output power will be cut off when the temperature is higher than the factory-preset value for 5 seconds. When the protection happens, the Green LED will flash in such a way “ -, -, -” .Over-Heat Protection: ☆☆☆

11. Motor Rotation: Face to the motor shaft (that means the endbell of the motor is far from your face), and move the throttle stick to forward zone. If this programmable item is set to “CCW”, the shaft runs counter-clockwise; if it is set to “CW”, the

shaft runs clockwise.

12. We strongly suggest you set the “Cell Count” manually instead of using the “Auto-identification” mode.Cell Count:

Reset All Items to Default Values

At any time when the throttle is located in neutral zone (except in the throttle calibration or parameters program process), press and hold the “SET” key for over 3 seconds, the red LED and green LED will flash

simultaneously , which means each programmable item has be reset to its default value. The ESC needs to be restarted to complete the reset process.

Click the SET button to choose the

option, the times the red LED

blinks indicates the option number

you are going to select.

After entering the

corresponding item, the

red LED starts to blink,

the times it blinks

represents the current

option number.

Press SET key to choose the value,

the flash times of the RED LED

means the option number.

(Once means the 1st option,

twice means the 2nd option, etc.)

USER MANUAL

16BL30 • 10BL60 • 8BL150

Brushless Electronic Speed Controller

This brushless system is

powerful and dangerous,

for the safety of your

own and those people

around you, please turn

on the ESC while

keeping all the wheels in

the air.

1. Turn on the transmitter, and set parameters (of the throttle channel) like “D/R, “EPA”, “ATL” to 100% (if there is no LCD display

on the transmitter, please adjust the corresponding knob to its limit). Set the throttle trim to 0 (if there is no display, then adjust the

knob to the neutral position). For FUTABA

T M

and similar transmitters, set the throttle direction to “REV”, while the throttle direction

of others to “NOR”. Please disable the built-in ABS brake function in your transmitter.

2. Hold the SET button while sliding the switch to the ON position, and then release the “SET” button the moment when the Red

LED starts to blink. (If you don’t release the SET button in 3 seconds, the ESC will enter the program mode, in such a case, please

switch off the ESC and re-calibrate the throttle range again from Step 1.)

Hold down the set

button.

Move the throttle stick to the neutral position and press

the set button.

Turn on the

switch Release the set

button once the LED

flashes.

Set the 3 points according to pictures

• The neutral point. • The end point of the forward direction. • The end point of the backward/brake direction.

When the process of calibration is finished, the motor can be started after 3 seconds.

The Green LED

flashes once and

motor emits

“Beep” tone.

Move the throttle stick to the end position of forward

and press the set button.

The Green LED flashes

twice and motor emits

“Beep-Beep”

tone.

Move the throttle stick to the end position of forward

and press the setup button.

The Green LED flashes

twice and motor emits

“Beep-Beep-

Beep” tone.

Battery

Motor

Blue

Yellow

Orange

Receiver

Switch

Electronic Speed Controller

External Programming

Port for Connecting

Program Card.

Termékspecifikációk

Márka:	Hobbywing
Kategória:	Rádióvezérlésű játékok
Modell:	QuicRun 10BL60

Szüksége van segítségre?

Ha segítségre van szüksége Hobbywing QuicRun 10BL60, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek

Az Ön neve*

Az Ön e-mail címe*

Írja ide kérdését

Útmutatók Rádióvezérlésű játékok Hobbywing

Hobbywing XeRun XR10 Pro WP Útmutató

25 Szeptember 2024

Hobbywing XeRun XR10 Stock Spec G2 Útmutató

25 Szeptember 2024

Hobbywing XeRun XR10 Justock G3S Útmutató

25 Szeptember 2024

Hobbywing XeRun XR8 PRO G3 Útmutató

25 Szeptember 2024

Hobbywing XeRun XR10 Justock G3 Handout Útmutató

25 Szeptember 2024

Hobbywing XeRun XR8 Plus G2S Útmutató

25 Szeptember 2024

Hobbywing XeRun XR10 Pro 1S Heavy Duty Útmutató

25 Szeptember 2024

Hobbywing XeRun XR10 Stock Spec 1S Útmutató

25 Szeptember 2024

Hobbywing XeRun XR10 PRO 160A Útmutató

25 Szeptember 2024

Hobbywing Xerun V10 G3 Útmutató

3 Szeptember 2024

Útmutatók Rádióvezérlésű játékok

Legújabb útmutatók Rádióvezérlésű játékok

Reely JoVage 4x4 V2 Útmutató

12 December 2024

MJX Hyper GO Útmutató

12 December 2024

Amewi MEW4 Útmutató

11 December 2024

Spektrum AR6600T Útmutató

15 Október 2024

Little Tikes Tire Twister Útmutató

8 Október 2024

Futaba 12Z Útmutató

4 Október 2024

Graupner 33718.XT60 Útmutató

3 Október 2024

Proline Trencher Útmutató

3 Október 2024

Amewi Hyper Go Útmutató

1 Október 2024

Carson Drift Burner Útmutató

1 Október 2024