Használati útmutató Hobbywing HW30401054

Hobbywing Rádióvezérlésű játékok HW30401054

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Hobbywing HW30401054 (1 oldal) a Rádióvezérlésű játékok kategóriában. Ezt az útmutatót 3 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/1
It’s important to select the FDR/gear ratio properly, as improper FDR/gear ratio may cause you great loss. Therefore, please choose the gear ratio by referring to the following points!
1. Operating Temperature of the Motor
The motor temperature should be lower than 100 during the operation. Temperatures above 100 will weaken the magnet and may partly melt the coils and eventually damage the ESC (due to strong ℃/212℉ ℃
current). Therefore, the most effective way to prevent overheat is to select the right gear ratio.
2. Principle of Gear Ratio Selection
To avoid potential risks such as ESC/motor damage or malfunction caused by overheat, please start with a very small pinion first and check the ESC & motor temperatures regularly throughout the run. This is the only
way to guarantee that your motor won’t overheat. If the motor and ESC temperatures remain stable and low in the running, then you can slowly increase the pinion size while monitoring temperatures to determine
the safe gearing for your vehicle, climate and track condition. Because these elements may change, so please keep monitoring the ESC & motor temperatures to protect your electronics from damage.
• (With the motor direction set to CCW), take the graduation/value after "CCW" on the motor case as the starting point when
adjusting the timing. (With the reversed triangle pointing at a value/graduation,) the smaller/bigger the value,
the smaller/bigger the timing. The timing is 40 degrees (as shown in picture 1) when the motor direction is set to CCW.
• (With the motor direction set to CW), take the graduation/value after "CW" on the motor case as the starting point when
adjusting the timing. (With the reversed triangle pointing at a value/graduation,) the smaller/bigger the value,
the smaller/bigger the timing. The timing is 20 degrees (as shown in picture 1) when the motor direction is set to CW.
• The motor timing is 30 degrees by default (as shown in picture 2). The motor timing should be within 30 to 40 degrees if you
want to activate the Turbo timing. And the timing can be within 20 to 40 degrees if you have no intention to activate the Turbo timing.
Warnings
CA UT IONS
Thank you for purchasing the XERUN 3652/3660 G2, HOBBYWING’s high performance
sensored brushless motor! Brushless power systems can be very dangerous, any improper
use may cause personal injury and damage to the product and related devices. We
strongly recommend reading through this user manual before use. Because we have no
control over the use, installation, or maintenance of this product, no liability may be
assumed for any damages or losses resulting from the use of this product. We do not
assume responsibility for any losses caused by unauthorized modifications to our product.
AT T ENT ION
AT T ENT ION
01
06
FDR/Gear Ratio Selection
05
Timing Adjustment
02
Features
07
Assembly/Disassembly
For prolonging the motor life and raising its efficiency, we recommend checking and cleaning the motor regularly. About the frequency, it depends on the times you
use the motor and the track condition. Please refer to the following diagrams to assemble your motor and dismantle it in the reverse order if necessary.
Parts List:
USER MANUAL
XERUN 3652/3660 G2
Sensored Brushless Motor
04
Installation & Connection
1. How to Mount the Motor into a RC vehicle
M3 mounting screws (6*M3) are needed here, as the mounting holes are 5mm in depth, so we don’t recommend using the M3 screws
with the length exceeds 8mm to mount the motor into your vehicle.
2. How to Connect the Motor to an ESC
There are three power wires coming from the ESC must be soldered to the motor. They are usually color coded as Blue for Wire A, Yellow
for Wire B and Orange for Wire C. When connecting the power wires between the ESC and motor, please make sure that you match ESC
Wire A to Motor Phase A, ESC Wire B to Motor Phase B and ESC Wire C to Motor Phase C (this is very important).
• When using a Sensored ESC, make sure the sensor cable is clean and undamaged first and then connect the sensor cable to both the
ESC and the motor in the correct direction.
• When using a Sensorless ESC, swap any two wires if the motor runs in reverse.
3. Recheck the Installation & Connections
Recheck the installation and all the connections before turning on the power.
3100
3800
4300
5100
6100
3100
3800
4300
3200
3600
4300
0.0087Ω
0.0059Ω
0.0052Ω
0.0035Ω
0.0029Ω
0.0087Ω
0.0059Ω
0.0052Ω
0.0065Ω
0.0056Ω
0.0038Ω
2.9A
3.9A
4.2A
4.7A
5.9A
2.9A
3.9A
4.2A
3.7A
4.1A
4.7A
192g (6.77oz)
192g (6.77oz)
187g (6.60oz)
192g (6.77oz)
186g (6.56oz)
192g (6.77oz)
192g (6.77oz)
187g (6.60oz)
218g (7.69oz)
214g (7.55oz)
218g (7.69oz)
1/10th
Light-duty SCT
Truck
Monster Truck
1/10th
Heavy-duty SCT
Truck
Monster Truck
30401050
30401052
30401053
30401054
30401055
30401056
30401058
30401059
30401150
30401151
30401152
2-3S
2-3S
2S
2S
2S
2-3S
2-3S
2S
2-3S
2-3S
2S
4
Φ=3.175mm(0.125in)
L=15mm(0.591)
Φ=5mm(0.197in)
L=17mm(0.669in)
Φ=5mm(0.197in)
L=15mm(0.591in)
XERUN-3652SD-3100KV-D3.175-G2
XERUN-3652SD-3800KV-D3.175-G2
XERUN-3652SD-4300KV-D3.175-G2
XERUN-3652SD-5100KV-D3.175-G2
XERUN-3652SD-6100KV-D3.175-G2
XERUN-3652SD-3100KV-D5.0-G2
XERUN-3652SD-3800KV-D5.0-G2
XERUN-3652SD-4300KV-D5.0-G2
XERUN-3660SD-3200KV-D5.0-G2
XERUN-3660SD-3600KV-D5.0-G2
XERUN-3660SD-4300KV-D5.0-G2
Φ=36mm (1.417in)
L=52.5mm (2.067in)
Φ=36(1.417in)
L=62(2.44in)
03
Specifications
ModelPN KV
(No-load)
No-load
Current
Motor Diameter
& Length
Shaft Diameter
& Length Poles Weight ApplicationsLiPo Resistance
• Innovative 4-pole-8-magnet "staggered pole" rotor (Hobbywing-patented) with low cogging effect and torque pulsation greatly improves control feel around corners.
• Built-in chip for making the motor be easily identified by HOBBYWING ESCs. When pairing it with a HW 1/8th sensored ESC (i.e. XR8 SCT/Plus), the motor can work in the “sensored” mode at all times with great
output linearity after the identification. The Turbo timing is allowed to be activated for higher output.
• Magnetic ring mounted on the rotor protects the motor from signal interference and guarantees its super stability in the “sensored” mode.
• With the mechanical timing adjustable from 20 degrees to 40 degrees, users are able to have different output power.
• Turbine design implemented by the rotor accelerates the internal air circulation and reduces heat.
• Rebuild-able design (partially rebuild-able) and screw-less motor case for easy routine maintenance effectively prolong the motor life and raise the motor effficiency.
• CNC machined aluminum housing, high purity copper windings, advanced rotor structure, high-quality alloy steel output shaft, high-precision bearings for high durability and smoothness.
• New-style “U” solder tabs at the bottom of the motor for easy soldering and wiring.
17mm 62mm
4.5mm
Ø5mm
15mm
20.6mm
Ø35.9mm
6-M3
Ø25.4mm
60°
C.C.W
XERUN 3660SD G2XERUN 3652SD G2XERUN 3652/3660SD G2 XERUN 3652/3660SD G2
52.5mm 15mm
4.5 / 2.8mm
Ø Ø3.1755 / mm
Picture 1 Picture 2
Back End Bell x 1PCS
Stator Set x 1PCS
Screws for Fastening
the Back End Bell
2PCS (M2.5*8.0mm)
Rotor x 1PCS
1 2 3 4 5
Mount washers
( the wave washer first,
then the flat washer ) Mount the motor rotor Mount the back end bell set
Mount screws for
fastening the back end bell
Picture of the
assembled motor
XERUN 3660SD G2
Brushless Electronic Speed Controller
Sensor wire
Motor B
Motor A
Motor C
• Never leave this product unsupervised when it is powered on.
• Ensure all wires and connections are well insulated before connecting the motor to related devices,
as short circuit will damage your motor.
• Please strictly follow the A-A, B-B and C-C wiring order when connecting an ESC to the motor.
• Never allow this product to come in contact with water, oil, fuel or other electro-conductive liquids.
If this happens, stop the use of your product immediately and let it dry carefully.
• Read through the manuals of all power devices and chassis and ensure the power configuration is
rational before using this unit.
• Never hit full throttle before installing the pinion, as high speed rotation may cause damage to the
motor in circumstances of no load.
• Ensure all devices are well connected, in order to prevent poor connection that may cause your
vehicle to lose control or other unpredictable issues such as damage to the device.
• Stop using the motor when its shell temperature exceeds 100℃/212℉; otherwise the rotor may be
demagnetized and cause irreversible damage to your motor.
Flat Washer x 1Pcs
Wave Washer x 1Pcs

Termékspecifikációk

Márka: Hobbywing
Kategória: Rádióvezérlésű játékok
Modell: HW30401054

Szüksége van segítségre?

Ha segítségre van szüksége Hobbywing HW30401054, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók Rádióvezérlésű játékok Hobbywing

Hobbywing

Hobbywing XeRun XR10 Pro WP Útmutató

25 Szeptember 2024
Hobbywing

Hobbywing XeRun XR10 Stock Spec G2 Útmutató

25 Szeptember 2024
Hobbywing

Hobbywing XeRun XR10 Justock G3S Útmutató

25 Szeptember 2024
Hobbywing

Hobbywing XeRun XR8 PRO G3 Útmutató

25 Szeptember 2024
Hobbywing

Hobbywing XeRun XR10 Justock G3 Handout Útmutató

25 Szeptember 2024
Hobbywing

Hobbywing XeRun XR8 Plus G2S Útmutató

25 Szeptember 2024
Hobbywing

Hobbywing XeRun XR10 Pro 1S Heavy Duty Útmutató

25 Szeptember 2024
Hobbywing

Hobbywing XeRun XR10 Stock Spec 1S Útmutató

25 Szeptember 2024
Hobbywing

Hobbywing XeRun XR10 PRO 160A Útmutató

25 Szeptember 2024
Hobbywing

Hobbywing Xerun V10 G3 Útmutató

3 Szeptember 2024

Útmutatók Rádióvezérlésű játékok

Legújabb útmutatók Rádióvezérlésű játékok

Reely

Reely JoVage 4x4 V2 Útmutató

12 December 2024
MJX

MJX Hyper GO Útmutató

12 December 2024
Amewi

Amewi MEW4 Útmutató

11 December 2024
Spektrum

Spektrum AR6600T Útmutató

15 Október 2024
Little Tikes

Little Tikes Tire Twister Útmutató

8 Október 2024
Futaba

Futaba 12Z Útmutató

4 Október 2024
Graupner

Graupner 33718.XT60 Útmutató

3 Október 2024
Proline

Proline Trencher Útmutató

3 Október 2024
Amewi

Amewi Hyper Go Útmutató

1 Október 2024
Carson

Carson Drift Burner Útmutató

1 Október 2024