Használati útmutató Hobbywing 30850000

Hobbywing Rádióvezérlésű játékok 30850000

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Hobbywing 30850000 (1 oldal) a Rádióvezérlésű játékok kategóriában. Ezt az útmutatót 2 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/1
This Electronic Power Switch features multiple functions like battery capacity indication,
low-voltage indication, over-current protection, short-circuit protection and thermal
protection; it can control the ON/OFF of current flow to the receiver, and it is operated by
only one button, this helped to solve problems like bad contact caused by vibration or
oxidation of contacts conventional mechanical switches have. As its case is made of plastic,
it can be easily mounted at any place via the double-faced adhesive tape.
Besides, the waterproof design makes it applicable for all weather conditions.
Please connect the JR female connector (Input end) to the receiver battery and plug the JR male connector (Output end) into the Battery channel or any other unoccupied channel on the receiver
according to the following diagram.
Introduction
CA UT IONS
Thank you for purchasing this HOBBYWING product! Devices used on RC
models can be dangerous, any improper use may cause personal injury and
damage to devices, so please make sure to read through this manual before
use. In that we have no control over the use, installation and maintenance of
this product or other related electronics, no liability may be assumed nor will
be accepted for any damages, losses or costs resulting from the use of the
product. Besides, we don’t shoulder any responsibility for any losses caused by
unauthorized modifications to our product. The last but not least, we have the
right to change the product design, appearance, features and operating
requirements without notice.
AT T ENT ION
01
02
Begin to Use the Electronic Power Switch
03
Switching On/Off & Setting
04
Explanations for Different LED Status
05
Other Protections & Indications
Switching On/Off
1
Setting (Battery Type)
2
NiMH
LiPo LiFe
BATT TYPE LED
Battery Type
Green
LiPo
Blue
LiFe
Red
NiMH
POWER LED
Remaining Capacity
Solid Green
80%~100%
Solid Orange
60%~80%
Solid Red
30%~60%
Blinking Red
0%~30%
Specifications
LiPo / LiFe / NiMH
2S LiPo / 2S LiFe / 5S NiMH
12A
26.5X19.7X10.5mm (LxWxH)
7.5g
Battery
Receiver
Electronic Power Switch
Switching On:
Please press the power (/RED) button to turn on the electronic switch after connecting
it to the battery; then both the POWER LED and the BATT TYPE LED will come solid on.
(For detailed explanation about LED status, please check the two forms below)
It’s important to set the battery type properly. If not, then the battery capacity indicator and low-voltage indicator will function abnormally.
Therefore, when the first time you turn on this switch and find the color of the BATT TYPE LED doesn’t match with the actual battery type, please set
it again. And you also need to reset the battery type after changing another type of battery. The following part explains how to set the battery type:
Keep pressing the POWER button after turning on the electronic switch, then the BATT TYPE LED will blink, about 3 seconds later the switch will
enter the battery type selection mode and the LED will flash Green/Blue/Red circularly; release the button, then you can select the corresponding
battery type to the color. (Please check the “BATT TYPE LED” form below for reference.)
Low-voltage Indication
When the battery voltage goes below the following threshold value for about 2 seconds, the POWER LED will blink RED slowly in this way “ ”, but the electronic switch won’t cut off its power ☆ ☆ ☆, ,
output. Threshold Voltage of Different Batteries are listed below:
For a 2S LiPo: 6.0V;
For a 2S LiFe: 4.0V;
For a 5cells Ni-MH: 4.5V;
Thermal / Overheat Protection
1. Threshold “Temperature”: 100 (212℃ ℉);
2. When the internal temperature of the electronic switch goes above 100 (212 ) for about 2 seconds, the POWER LED will flash RED in the following way “ ”, but the switch ℃ ℉ ☆☆☆ ☆☆☆ ☆☆☆, ,
will continue outputting power.
Over-current / Short-circuit Protection
1. Trigger condition of the over-current protection: The current is between 20~39Amp and that lasts
for about 500ms;
Trigger condition of the short-circuit protection: The current is over 40Amp and that lasts for
about 500µs.
2. When the over-current/short-circuit protection is activated, the electronic switch will automatically
CUT OFF the output and enter the protection; and the POWER LED will blink RED in this way
“☆☆ ☆☆ ☆☆, , ”.
Battery Polarity Reversal Protection
( )Note: It only works when no load is connected to the switch
1. If it’s not connected to any load, the electronic switch will trigger this protection to stop itself from
starting up when detected the battery polarity at the input end is reversed.
2. If it’s connected to some load and the battery polarity is wrong, the receiver and other connected
devices will get damaged as they get the polarity-reversed voltage from the electronic power switch.
Switching Off:
After turning on the electronic switch, press the power button again for about 0.5
second can turn off the switch and make both LEDs go out.
Press the power button, then both LEDs will turn solid on. Press the button for about 0.5 second, both LEDs will turn off.
BATT TYPE LED Different LED color indicates different battery type. POWER LED: For battery capacity indication.：
USER MANUAL
Electronic Power Switch
Battery Type
Input Voltage
Max. Current
Size
Weight
Either over-current protection or short-circuit protection can cause the
receiver to lose power supply, so please ensure the current draw of all
the devices connected to the receiver is below 12Amp (12 Amp is the
maximum output current this switch can stand).
IMPORT ANT
For avoiding possible damages caused by battery reversal, we strongly
recommend disconnecting the JR male connector (Output end) from your
receiver before connecting this electronic power switch to the battery;
After connecting to the battery, try to turn on the electronic switch first;
if you can turn it on normally, then you can plug the JR male connector
(Output end) into the receiver.
IMPORT ANT

Termékspecifikációk

Márka: Hobbywing
Kategória: Rádióvezérlésű játékok
Modell: 30850000

Szüksége van segítségre?

Ha segítségre van szüksége Hobbywing 30850000, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók Rádióvezérlésű játékok Hobbywing

Hobbywing

Hobbywing XeRun XR10 Pro WP Útmutató

25 Szeptember 2024
Hobbywing

Hobbywing XeRun XR10 Stock Spec G2 Útmutató

25 Szeptember 2024
Hobbywing

Hobbywing XeRun XR10 Justock G3S Útmutató

25 Szeptember 2024
Hobbywing

Hobbywing XeRun XR8 PRO G3 Útmutató

25 Szeptember 2024
Hobbywing

Hobbywing XeRun XR10 Justock G3 Handout Útmutató

25 Szeptember 2024
Hobbywing

Hobbywing XeRun XR8 Plus G2S Útmutató

25 Szeptember 2024
Hobbywing

Hobbywing XeRun XR10 Pro 1S Heavy Duty Útmutató

25 Szeptember 2024
Hobbywing

Hobbywing XeRun XR10 Stock Spec 1S Útmutató

25 Szeptember 2024
Hobbywing

Hobbywing XeRun XR10 PRO 160A Útmutató

25 Szeptember 2024
Hobbywing

Hobbywing Xerun V10 G3 Útmutató

3 Szeptember 2024

Útmutatók Rádióvezérlésű játékok

Legújabb útmutatók Rádióvezérlésű játékok

Reely

Reely JoVage 4x4 V2 Útmutató

12 December 2024
MJX

MJX Hyper GO Útmutató

12 December 2024
Amewi

Amewi MEW4 Útmutató

11 December 2024
Spektrum

Spektrum AR6600T Útmutató

15 Október 2024
Little Tikes

Little Tikes Tire Twister Útmutató

8 Október 2024
Futaba

Futaba 12Z Útmutató

4 Október 2024
Graupner

Graupner 33718.XT60 Útmutató

3 Október 2024
Proline

Proline Trencher Útmutató

3 Október 2024
Amewi

Amewi Hyper Go Útmutató

1 Október 2024
Carson

Carson Drift Burner Útmutató

1 Október 2024