Használati útmutató Hikvision DS-2CE16D5T-AVFIT3

Hikvision Térfigyelő kamera DS-2CE16D5T-AVFIT3

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Hikvision DS-2CE16D5T-AVFIT3 (4 oldal) a Térfigyelő kamera kategóriában. Ezt az útmutatót 4 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/4
1 Introduction
1.1 Product Features
1.2 Overview
2 Installation
Before you start:
Thank you for purchasing our product. If there
are any questions, or requests, please do not
hesitate to contact the dealer.
This manual applies to DS-2CE56C5T-VFIT3 and
DS-2CE16C5T-(A)VFIR3.
This manual may contain several technical
incorrect places or printing errors, and the
content is subject to change without notice.
The updates will be added to the new version of
this manual. We will readily improve or update
the products or procedures described in the
manual.
DISCLAIMER STATEMENT
Underwriters Laboratories Inc. (”UL” has not)
tested the performance or reliability of the
security or signaling aspects of this product.
UL has only tested for fire, shock or casualty
hazards as outlined in Ul’s Standard(s) for Safety,
UL60950-1. UL Certification does not cover the
performance or reliability of the security or
signaling aspects of this product. UL MAKES NO
REPRESENTATIONS, WARRANTIES OR
CERTIFICATIONS WHATSOEVER REGARDING
0100001040603
Regulatory Information
FCC Information
FCC compliance: This equipment has been
tested and found to comply with the limits for a
digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide
reasonable protection against harmful
interference when the equipment is operated in
a commercial environment. This equipment
generates, uses, and can radiate radio
frequency energy and, if not installed and used
in accordance with the instruction manual, may
cause harmful interference to radio
communications. Operation of this equipment in
a residential area is likely to cause harmful
interference in which case the user will be
required to correct the interference at his own
expense.
FCC Conditions
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful
interference.
2. This device must accept any interference
received, including interference that may
cause undesired operation.
EU Conformity Statement
2006/66/EC (battery directive):
This product contains a battery
that cannot be disposed of as
unsorted municipal waste in the
European Union.
See the product documentation for specific
battery information. The battery is marked with
this symbol, which may include lettering to
indicate cadmium (Cd), lead (Pb), or mercury (Hg).
For proper recycling, return the battery to your
supplier or to a designated collection point. For
more information see:www.recyclethis.info.
THE PERFORMANCE OR RELIABILITY OF ANY
SECURITY OR SIGNALING RELATED FUNCTIONS
OF THIS PRODUCT.
This camera adopts new generation sensor with
high sensitivity and advanced circuit board design
technology. It possesses the features of high
resolution, low distortion, and low noise, etc. It is
extremely suitable for supervisory system and
image processing system.
The main features are as follows:
Figure 2-1 The Drill Template
UD.6L0201D1454A01
TURBO HD
720P Turret &Bullet Camera
User Manual
This product and - if applicable -
the supplied accessories too are
marked with "CE" and comply
therefore with the applicable harmonized
European standards listed under the Low Voltage
Directive 2006/95/EC, the EMC Directive 2004/
108/EC, the RoHS Directive 2011/65/EU.
upon the purchase of equivalent new equipment,
or dispose of it at designated collection points.
For more information see:www.recyclethis.info.
2012/19/EC (WEEE directive):
Products marked with this symbol
cannot be disposed of as unsorted
municipal waste in the European
Union. For proper recycling, return
this product to your local supplier
1.2.1 Overview of Type I Camera
l Please make sure that the device in the package
is in good condition and all the assembly parts
are included.
l Make sure that all the related equipment is
power-off during the installation.
l Check the specification of the products for the
installation environment.
l Check whether the power supply is matched
with your power output to avoid damage.
l Please make sure the wall is strong enough to
withstand three times the weight of the camera
and the mounting.
l If the wall is the cement wall, you need to insert
expansion screws before you install the camera.
If the wall is the wooden wall, you can use
self-tapping screw to secure the camera.
l If the product does not function properly,
please contact your dealer or the nearest
service center. Do not disassemble the camera
for repair or maintenance by yourself.
2.1 Installation of Type CameraI
l High performance CMOS sensor and high
resolution bring high-quality image;
l Low illumination, 0.01 Lux @ (F1.2, AGC ON),
0 Lux with IR;
l Support IR cut filter with auto switch;
l OSD menu, parameters are configurable;
l Support auto white balance, auto gain control,
electronic shutter control and internal
synchronization;
l Advanced Engineering Design and patent
universal adjustable structure provides
convenient adjustment and high reliability;
lSMART IR mode;
l Unit transmission control;
l Advanced 3-axis design meets different
installation requirements;
l Ingress protection: IP66.
1.Drill the screw holes and the cable hole on the
ceiling according to the supplied drill template.
2 Push the lock button to disassemble the camera
.
from the mounting base.
3.Fix the mounting base to the ceiling.
Figure 2-2 Release The Lock Screw
Steps:
PUSH
The HD video output mode is set as the default.
You can short the white and black line-end of the
control switch cable or press the dip switch to
switch the mode as CVBS output.
Figure 1-2 Overview of Type CameraII
Figure 1-1 Overview of Type I Camera
1.2.2 Overview of Type Camera
HD Video Cable
CVBS Cable
Switch Cable
Enclosure
Zoom & Focus
Lock ButtonLock Button
Mounting Base
Camera
Powe r Cable
Mounting Base
Sun Shield
Main Body
Lens
IR LED
HD Video Cable
CVBS Cable
Power Cable
Adjusting Sheet
Focus
Zoom
Dip Switch
Menu Button
Figure 3-3 Manual of WB
Figure 3-4 Smart Mode of DAY&NIGHT
Figure 3-5 Video Settings
3.3 DAY & NIGHT
3.4 Video Setting
Move the cursor to the VIDEO SETTING, and press
the menu button to enter the video configuration
interface. As shown in Figure 3-5.
3.5 FUNCTION
Move the cursor to DAY & NIGHT, and select
COLOR B/W SMART, , or as the DAY & NIGHT mode.
3.6 Reset
Reset all the settings to the default.
3.7 Save & Exit
Move the cursor to , and press OK toSAVE & RESET
save the settings and exit the menu.
3 Menu Operation
3.1 AE
Move the cursor to AE, and you can adjust the
image brightness by the , ,BRIGHTNESS AE MODE
AGC SENS-UP, and in this menu.
As shown in Figure 3-2.
.
Figure 3-1 Main Menu
Figure 3-2 AE
4.Route the cables to the cable hole and connect
the corresponding cables.
5.Secure the camera to the mounting base by
tightening the lock screw.
6.Adjust the camera according to the figure below
to get an optimum angle.
Figure 2-3 3-axis Adjustment
7.Use the screwdriver to adjust the ZOOM screw
and the FOCUS screw until you get the optimum
image.
Figure 2-4 Zoom and Focus Adjustment
2.2 Installation of Type CameraII
Steps:
1. Drill the screws holes on the ceiling according
to the supplied drill template.
Screw Hole
Template
Figure 2-5 The Drill Template
2.Route the corresponding cables.
3.Secure the camera to the ceiling with the self-
tapping Screws.
Figure 2-6 Secure the Camera to the Ceiling
4.Connect the corresponding cables.
5. Loosen the T screw, R screw and P screw
successively and adjust the camera according to
the figure below to get an optimum angle. Tighten
the screw after completing the adjustment.
R Screw
T Screw
P Screw
6.Adjust the Zoom Screw and Focus Screw till you
get the optimum surveillance angle.
Figure 2-7 3-axis Adjustment
Figure 2-8 Zoom and Focus Adjustment
BRIGHTNESS: Set the brightness value from
1 to 10 to darken or brighten the image.
: Set AE mode as GLOBLE AE, andAE MODE
D-WDR.
AGC HIGH MIDDLE LOW: , , and can be set for the
AGC level. Select OFF to disable the AGC.
: Set the SENSE UP value from 0 to 16.SENSE UP
3.2 WB
Move the cursor to WB, and you can set White
Balance mode as and in this menuAUTO MANUAL .
AUTO: white balance is being adjusted
automatically.
: Set the valueMANUAL R GAIN/B GAIN
from 1 to 10. As shown in Figure 3-3.
COLOR: The image is colored in day mode all the
time.
: The image is black & white all the time, andB/W
the IR LED turns on in the low-light conditions.
: Select to turn on/off the INFRARED_LAMPSMART
and to set the Smart IR level from 1to 16.
As shown in Figure 3-4.
SAMRT
1. INFRARED_LAMP OFF
2. SMART IR 0-|--5
3. RETURN 8
: Set the CONTRAST value from 1 to 10.CONTRAST
: Set the edge and detail sharpnessSHARPNESS
value from 1 to 10.
COLOR GAIN: Set the color gain from 1 to 10.
: Set the 3D NR level as , ,3D NR High Middle
and . Select to disable the 3D NR.Low OFF
: Set the mirror mode as , ,MIRROR OFF H
, or .V HV
You can set , , andDETECTION MASKING ZOOM IN
of the camera in this menu.LANGUAGE
FUNCTION
1. DETECTION 8
2. MASKING 8
3. ZOOM IN 50-|--100
4. LANGUAGE ENGLISH
5. RETURN 8
Figure 3-6 Function
DETECTION: Set the motion sensitivity as
, , or . Select an AREA toWEAK LOW MIDDLE HIGH
enter the motion detection AREA menu. As shown
in Figure 3-7.
: Set the status as / . Select a color forAREA OFF ON
area border. Move the joystick up/down and right
/left to set the horizon/vertical size and position.
As shown in Figure 3-8.
MASKING: Select a masking back ground color.
Select an AREA to enter the masking AREA menu.
As shown in figure 3-9.
: Set the status as / . Move the joystickAREA OFF ON
up/down and right/left to set the horizon/vertical
size and position.
As shown in Figure 3-10.
ZOOM IN: The ZOOM IN value can be adjusted from
50 to 100.
LANGUAGE: Chinese and English are selectable.
DETECTION
1. SENSITIVITY HIGHT
2. AREA NO.0 8
3. AREA NO.1 8
4. AREA NO.2 8
5. AREA NO.3 8
6. RETURN 8
AREA
1. STATUS OFF
2. COLOR WHITE
3. HORIZON SIZE 0
4. VERTICAL SIZE 0
5. HORIZON MOVE 0
6. VERTICAL MOVE 0
7. RETURN 8
Figure 3-7 Detection
Figure 3-8 Detection Area
MASKING
1. COLOR WHITE
2. AREA NO.0 8
3. AREA NO.1 8
4. AREA NO.2 8
5. AREA NO.3 8
6. AREA NO. 8
7. AREA NO.5 8
8. AREA NO.6 8
9. AREA NO.7 8
10.RETURN 8
AREA
1. STATUS OFF
2. HORIZON SIZE 0
3. VERTICAL SIZE 0
4. HORIZON MOVE 0
5. VERTICAL MOVE 0
6. RETURN 8
Figure 3-9 Detection Area
Figure 3-10 Detection
AE
1. BRIGHTNESS 1-|--10
2. AE MODE DWDR
3. AGC OFF
4. SENSE UP 0-|---16
5. RETURN 8
MANUAL
1. R GIAN 1-|--10
2. B GAIN 1-|--10
3. RETURN 8
0 ~360
0 ~75
0~360
MENU
AE WB DAY
&NIGHT
VIDEO
SETTING FUNCTION RESET
SAVE
&EXIT
BRIGHTNESS
AE MODE
AGC
SENSE UP
AUTO
MANUAL
COLOR
B/W
CONTRAST
SHARPNESS
COLOR
GAIN
3D NR
MIRROR
DETECTION
MASKING
ZOOM IN
LANGUAGE
SMART
VIDEO
STANDARD
MAIN
MENU
VIDEO SETTING
1. CONTRAST 1-|--10
2. SHARPNESS 8
3. COLOR GAIN 1-|--10
4. 3D NR OFF
5. MIRROR OFF
6. RETURN 8
A coaxial camera controller (purchase separately)
is required to select the menu and adjust the
camera parameters.
Focus
Zoom

Termékspecifikációk

Márka: Hikvision
Kategória: Térfigyelő kamera
Modell: DS-2CE16D5T-AVFIT3

Szüksége van segítségre?

Ha segítségre van szüksége Hikvision DS-2CE16D5T-AVFIT3, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók Térfigyelő kamera Hikvision

Hikvision

Hikvision DS-2CE10DF8T-FSLN Útmutató

6 Április 2025
Hikvision

Hikvision DS-2CE56C0T-IRPF Útmutató

5 Április 2025
Hikvision

Hikvision DS-2CD2141G1 Útmutató

5 Április 2025
Hikvision

Hikvision DS-2CE59U1T-AVPIT3ZF Útmutató

13 Január 2025
Hikvision

Hikvision IDS-2CD7526G0-IZHSY Útmutató

13 Január 2025
Hikvision

Hikvision DS-2CD2163G0-I(S) Útmutató

13 Január 2025
Hikvision

Hikvision DS-2CD2H83G1-IZS Útmutató

13 Január 2025
Hikvision

Hikvision DS-2CE16H0T-IT1E Útmutató

12 Január 2025
Hikvision

Hikvision THC-T127-PTLTS Útmutató

7 Január 2025
Hikvision

Hikvision DS-2CE16U0T-LF Útmutató

19 December 2024

Útmutatók Térfigyelő kamera

Legújabb útmutatók Térfigyelő kamera

Dahua Technology

Dahua Technology Pro IPC-HDPW5442G-Z Útmutató

15 Január 2025
Toshiba

Toshiba IKS-WR7412 Útmutató

14 Január 2025
Flir

Flir FC-610 O Útmutató

13 Január 2025
AVerMedia

AVerMedia FC1320-P Útmutató

13 Január 2025
Digitus

Digitus OptiMax DN-16037 Útmutató

13 Január 2025
ZKTeco

ZKTeco AntarVis 2.0 Útmutató

12 Január 2025
Speco Technologies

Speco Technologies O2P30X Útmutató

12 Január 2025
Kguard

Kguard QRT-501 Útmutató

12 Január 2025
Vivotek

Vivotek AI-108 Útmutató

12 Január 2025
Yale

Yale WIPC-303W Útmutató

12 Január 2025