Használati útmutató GT 802

Olvassa el alább 📖 a magyar nyelvű használati útmutatót GT 802 (16 oldal) a autóriasztó kategóriában. Ezt az útmutatót 9 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Oldal 1/16
GT 800/1/2/3
USER AND INSTALLATION MANUAL
1
SUMMARY
2
1.0 - INSTALLATION AND CONNECTIONS Page. 3
2.0 - GENERAL CONNECTION DIAGRAM Page. 5
3.0 - DESCRIPTION OF THE PROGRAMMABLE FUNCTIONS Page. 6
3.1 - Self-coding vehicle indicators impulses number Page. 6
3.2 - Switches/Discriminators signals stabilizer Page. 6
3.3 - Memorization of switches/discriminators signals only after actuator signals Page. 6
3.4 - Memorisation of actuator signals of changeable type Page. 6
3.5 - Anti-hijack door signal stabilizer Page. 6
3.6 - Acoustic signal when arming/disarming the alarm system Page. 6
3.7 - Visual signal when arming/disarming the alarm system Page. 6
3.8 - Courtesy light switching on when disarming Page. 6
4.0 - SET FUNCTIONS Page. 6
5.0 - DESCRIPTION OF THE ALARM SYSTEM ARMING/DISARMING COMMAND WIRES Page. 8
6.0 - DOORS LOCK/UNLOCK SIGNALS SELF-CODING Page. 8
7.0 - RAPID TEST Page. 9
8.0 - SELF-POWER SUPPLY Page. 10
9.0 - FINAL OPERATIONS Page. 10
10.0 - USER MANUAL Page. 11
10.1 - Alarm system arming/disarming Page. 11
10.2 - Electric windows closing command function Page. 11
10.3 - Protections Page. 11
10.4 - If the alarm sounds ... Page. 11
10.5 - Check status LED Page. 11
10.6 - Emergency disarming with “GT CARD CODE” Page. 12
10.7 - How to isolate additional sensors and ultrasonic sensor
when arming the alarm system Page. 12
10.8 - Anti-hijack function Page. 12
10.9 - Visual signal function when arming/disarming the alarm system Page. 13
10.10 - Acoustic signal function when arming/disarming the alarm system Page. 13
10.11 - Functions check Page. 13
11.0 - COMPLIANCE DECLARATION Page. 13
12.0 - WARRANTY CONDITIONS Page. 14
13.0 - TECHNICAL FEATURES Page. 15
3
1.0 - INSTALLATION AND CONNECTIONS
WARNINGS:
- Place the GT800 alarm in the engine compartment, away from direct sources of water
spray and high tension wiring.
- Solder and isolate all connections.
- Isolate the wires not connected.
- The alarm system should be mounted by a professional installer.
1 - Connect the BROWN wire to O/E vehicle earth.
2 - Connect the RED wire to a permanent 12 volts supply (use the supplied 15 Amp fuse).
3 - Connect the PINK wire of the alarm (max. capacity 80 mA) to the PINK wire of any additional
sensors/modules (i.e. microwave sensor, electric window module).
4 - Connect the GREEN/BLACK wire of the alarm to the GREEN/BLACK wire of any additional
sensors.
5 - Connect the YELLOW wire to an ignition switched live (+15/54) that remains live even
when the engine is being cranked. Do not connect to the same wire used for the engine
immobilisation.
6 - Connect the ORANGE wires to the left and right hand vehicle indicators.
7 - Connect the GREEN wire to the boot and bonnet pin switches, provided that they are
switched earth only.
8 - Connect the GREEN/BROWN wire to the existing doors pin switches, provided that they
are switched earth only.
9 - If you want to activate the ANTI-HIJACK FUNCTION connect the GREEN/BLUE wire to
the original driver’s door pin switch, provided that it is a switched earth only.
10 - Connect the BLUE/VIOLET wire to the “comfort” command of the vehicles equipped with
negative “comfort” closing function (the signal duration is of about 40 seconds).
11- The WHITE and GREY wires are used for the engine immobilisation on either diesel or
petrol vehicles. Cut the ignition switched live that feeds, depending on the type of vehicle, the
fuel pump relay, or the solenoid valve (diesel vehicles). Connect one end to the GREY wire
and the other to the WHITE wire.
WARNING:
- On the vehicles equipped with an ignition key transponder immobiliser, it is not
necessary to connect the WHITE and GREY wire of the alarm, therefore these two
wires can be isolated.
12 - The YELLOW/BLACK wire sends a negative intermittent signal when triggered alarm
(max 100mA). It can be used to command the vehicle’s horn relay.
13 - Place the LED/BUTTON on the dashboard (in a visible way) and connect it to the
connectors in the alarm wiring loom.

Termékspecifikációk

Márka: GT
Kategória: autóriasztó
Modell: 802

Szüksége van segítségre?

Ha segítségre van szüksége GT 802, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek




Útmutatók autóriasztó GT

GT

GT GT-913 Útmutató

19 Augusztus 2024
GT

GT 800-1 Útmutató

17 Augusztus 2024
GT

GT 615 Útmutató

14 Augusztus 2024
GT

GT GT909NL Útmutató

13 Augusztus 2024
GT

GT 801 Útmutató

11 Augusztus 2024
GT

GT 916 Útmutató

11 Augusztus 2024
GT

GT 636 Útmutató

8 Augusztus 2024
GT

GT GT-911 Útmutató

7 Augusztus 2024
GT

GT 136 Útmutató

6 Augusztus 2024
GT

GT GT-912 Útmutató

3 Augusztus 2024

Útmutatók autóriasztó

Legújabb útmutatók autóriasztó

Viper

Viper 4105V Útmutató

9 Április 2025
Gemini

Gemini 7463 Útmutató

23 Szeptember 2024
Gemini

Gemini 7090 Útmutató

21 Szeptember 2024
Gemini

Gemini 7502 Útmutató

15 Szeptember 2024
Audiovox

Audiovox CA1155E Útmutató

27 Augusztus 2024
HP

HP Rotary Lock Útmutató

23 Augusztus 2024
Spy

Spy FM5000 Útmutató

21 Augusztus 2024
Gemini

Gemini 823 Útmutató

20 Augusztus 2024