Használati útmutató Genelec 4030C

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Genelec 4030C (16 oldal) a Monitor kategóriában. Ezt az útmutatót 10 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Oldal 1/16
4030C
Operating Manual
2
General
The bi-amplied Genelec 4030C is an extremely
compact two way active loudspeaker designed
for xed installations. As an active loudspeaker, it
contains drivers, power ampliers, active crossover
filters and protection circuitry. The 4030C is
designed for indoor use only, in temperatures
between 15 to 35 degrees Celsius and relative
humidity between 20 % and 90 %.
The MDE™ (Minimum Diraction Enclosure™)
loudspeaker enclosure is made of die-cast
aluminium and shaped to reduce edge diraction.
Combined with the advanced Directivity Control
Waveguide TM (DCWTM ), this design provides
excellent frequency balance in difficult acoustic
environments.
Positioning the loudspeaker
Each 4030C is supplied with an integrated amplier
unit, mains cable, a 3-pin balanced Euroblock
connector for audio signal, a keyhole type wallmount
and an operating manual. After unpacking, place the
loudspeaker in its required listening position, taking
note of the line of the acoustic axis. The axis should
be pointed towards the center of the listening area.
Connections
Before connecting up, ensure that the loudspeakers
and the signal source have been switched o. The
power switch of the 4030C is located on the back
panel (see Figure 3). Connect the loudspeaker to
an earthed mains connection with the supplied
mains cable. Never connect the loudspeaker to
an unearthed mains supply or using an unearthed
mains cable. Audio input is via a 10 kOhm
balanced connector. The pin sequence of the
connector is shown in Figure 2.
Connect the signal cable to the 3-pole plug
provided with the loudspeaker and secure the
connections by tightening the screws on each
pole. Push the plug into the connector on the
loudspeaker.
If you want to daisy-chain multiple
loudspeakers, simply connect a second signal
cable to the plug and use it to route the signal to
the next loudspeaker (see Figure 4).
Never connect the 4030C to the loudspeaker
outputs of a power amplifier or an integrated
amplier or receiver.
Once the connections have been made, the
loudspeakers are ready to be switched on.
ISSTM Autostart
The automatic power saving function ISS (Intelligent
Signal Sensing) can be activated by setting the
“ISS” switch on the back panel to “ON.” Automatic
powering down to standby mode happens after a
certain time when playback has ended. The power
consumption in standby mode is typically less than
0.5 watts. Playback will automatically resume once
an input signal is detected from the source.
There is a slight delay in the automatic powering
up. If this is undesirable, the ISSTM function can be
disabled by setting the ISS” switch on the back
panel to OFF.” In this mode, the loudspeaker is
powered on and o using the power switch on the
back panel.
4030C
Active Loudspeaker

Termékspecifikációk

Márka: Genelec
Kategória: Monitor
Modell: 4030C

Szüksége van segítségre?

Ha segítségre van szüksége Genelec 4030C, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek




Útmutatók Monitor Genelec

Genelec

Genelec 4420A Útmutató

28 Szeptember 2024
Genelec

Genelec 8341A Útmutató

27 Szeptember 2024
Genelec

Genelec 7380A Útmutató

19 Szeptember 2024
Genelec

Genelec 1238AC Útmutató

13 Augusztus 2024
Genelec

Genelec 8350A Útmutató

2 Augusztus 2024
Genelec

Genelec 8320A Útmutató

2 Augusztus 2024
Genelec

Genelec 8331A Útmutató

1 Augusztus 2024
Genelec

Genelec 7370A Útmutató

30 Július 2024
Genelec

Genelec 7360A Útmutató

30 Július 2024
Genelec

Genelec 7050C Útmutató

29 Július 2024

Útmutatók Monitor

Legújabb útmutatók Monitor