Használati útmutató GE Profile JGP989BCBB

GE sütő Profile JGP989BCBB

Olvassa el alább 📖 a magyar nyelvű használati útmutatót GE Profile JGP989BCBB (72 oldal) a sütő kategóriában. Ezt az útmutatót 3 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/72
JGP989
ge.com
49-80388-1 10-06 JR
Owner’s Manual
& Installation
Instructions
Safety Instructions . . . .2–7
Operating Instructions
Downdraft Vent System . .10
Features . . . . . . . . . . . . . .8
Gas Surface Burners . . . . .9
Using Your Cooktop . . . .10
Care and Cleaning
Burner Assemblies . . . . .11
Burner Caps and Heads . .11
Burner Grates and
Vent Grille . . . . . . . . . . . .12
Control Knobs . . . . . . . .13
Glass Surface . . . . . . .13, 14
Vent Filter . . . . . . . . . . . .12
Installation Instructions
Ductwork . . . . . . .19–22, 27
Electrical
Connections . . . .23, 28, 29
Exhaust Blower Ratings .21
Final Assembly . . . . . . . .30
Installing
the Cooktop . . . . . . .25–28
Installing the Gasket . . . .24
Power Supply . . . . . . . . .23
Preparation . . . . . . . .17–19
Safety Precautions . . . . . .15
Unpacking
the Cooktop . . . . . . .16, 24
Troubleshooting
Tips . . . . . . . . . . . . . .31, 32
Consumer Support
Consumer Support . . . . .36
Product
Registration . . . . . . . .33, 34
Warranty . . . . . . . . . . . . .35
Write the model and serial
numbers here:
Model # __________________
Serial #____________________
Find these numbers on a label
under the cooktop, on the side
of the vent chamber.
Cooktop
Gas Downdraft
2
IMPORTANT SAFETY INFORMATION.
READ ALL INSTRUCTIONS BEFORE USING.
Safety InstructionsOperating InstructionsCare and CleaningTroubleshooting TipsConsumer Support
— Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.
—WHAT TO DO IF YOU SMELL GAS
■Do not try to light any appliance.
■ Do not touch any electrical switch; do not use
any phone in your building.
■ Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s
instructions.
■ If you cannot reach your gas supplier, call the
fire department.
— Installation and service must be performed by
a qualified installer, service agency or the gas
supplier.
WARNING: If the information in this manual
is not followed exactly, a fire or explosion may
result causing property damage, personal injury
or death.
WARNING!
For your safety, the information in this manual must be followed to minimize the risk of fire or
explosion, electric shock, or to prevent property damage, personal injury, or loss of life.
Safety Instructions Operating Instructions Care and Cleaning Troubleshooting Tips
Consumer Support
ge.com
IMPORTANT SAFETY NOTICE
The California Safe Drinking Water and Toxic Enforcement Act requires the Governor of California to
publish a list of substances known to the state to cause cancer, birth defects or other reproductive
harm, and requires businesses to warn customers of potential exposure to such substances.
Gas appliances can cause minor exposure to four of these substances, namely benzene, carbon
monoxide, formaldehyde and soot, caused primarily by the incomplete combustion of natural gas or
LP fuels. Properly adjusted burners, indicated by a bluish rather than a yellow flame, will minimize
incomplete combustion. Exposure to these substances can be minimized by venting with an open
window or using a ventilation fan or hood.
Have the installer show you the location of the cooktop gas shut-off valve and how to shut it off
if necessary.
■Have your cooktop installed and properly
grounded by a qualified installer, in
accordance with the Installation
Instructions. Any adjustment and service
should be performed only by qualified gas
cooktop installers or service technicians.
■Do not attempt to repair or replace any
part of your cooktop unless it is specifically
recommended in this manual. All other
service should be referred to a qualified
technician.
■Locate the cooktop out of kitchen traffic
path and out of drafty locations to prevent
poor burner performance.
■Plug your cooktop into a 120-volt
grounded outlet only. Do not remove the
round grounding prong from the plug.
If in doubt about the grounding of the
home electrical system, it is your personal
responsibility and obligation to have an
ungrounded outlet replaced with a
properly grounded, three-prong outlet in
accordance with the National Electrical
Code. Do not use an extension cord with
this appliance.
■Let the burner grates and other surfaces
cool before touching them or leaving
them where children can reach them.
■Be sure all packaging materials are
removed from the cooktop before
operating it to prevent fire or smoke
damage should the packaging material
ignite.
■Be sure your cooktop is correctly adjusted
by a qualified service technician or installer
for the type of gas (natural or LP) which
is to be used. Your cooktop can be
converted for use with either type of gas.
See the Installation Instructions in the
LP Conversion Kit.
WARNING: These adjustments must
be made by a qualified service technician
in accordance with the manufacturer’s
instructions and all codes and
requirements of the authority having
jurisdiction. Failure to follow these
instructions could result in serious injury
or property damage. The qualified
agency performing this work assumes
responsibility for the conversion.
■Do not leave children alone or unattended
where a cooktop is hot or in operation.
They could be seriously burned.
■Do not allow anyone to climb, stand or
hang on the cooktop.
■Do not operate or clean your cooktop if
the glass is broken or cracked. Cleaning
solutions and spillovers could penetrate the
broken cooktop and create a risk of
electric shock. Call for service immediately
if the cooktop glass breaks or cracks.
SAFETY PRECAUTIONS
3
4
Safety InstructionsOperating InstructionsCare and CleaningTroubleshooting TipsConsumer Support
IMPORTANT SAFETY INFORMATION.
READ ALL INSTRUCTIONS BEFORE USING.
■CAUTION: Items of interest to
children should not be stored in cabinets
above a cooktop—children climbing on the
cooktop to reach items could be seriously
injured.
■Always keep wooden and plastic utensils
and canned food a safe distance away from
your cooktop.
■Always keep combustible wall coverings,
curtains or drapes a safe distance from
your cooktop.
■Never wear loose-fitting or hanging
garments while using the appliance.
Be careful when reaching for items stored
in cabinets over the cooktop. Flammable
material could be ignited if brought in
contact with flame or hot surfaces and
may cause severe burns.
■Teach children not to play with the controls
or any other part of the cooktop.
■Always keep dish towels, dishcloths, pot
holders and other linens a safe distance
from your cooktop.
■Do not store flammable materials near
a cooktop.
■Do not store or use combustible materials,
gasoline or other flammable vapors and
liquids in the vicinity of this or any other
appliance.
■Do not let cooking grease or other
flammable materials accumulate on or
near the cooktop.
■Do not operate the burner without all
burner parts in place.
■Do not place hot cookware on the glass
cooktop. This could cause glass to break.
■Do not clean the cooktop with flammable
or volatile cleaning fluids.
■Do not clean the cooktop when the
appliance is in use.
■Avoid scratching the cooktop with sharp
instruments, or with rings and other jewelry.
■Never use the cooktop as a cutting board.
■Do not use water on grease fires. Never
pick up a flaming pan. Turn the controls
off. Smother a flaming pan on a surface
burner by covering the pan completely with
a well-fitting lid, cookie sheet or flat tray.
Use a multi-purpose dry chemical or
foam-type fire extinguisher.
■Flaming grease outside a pan can be put
out by covering it with baking soda or, if
available, by using a multi-purpose dry
chemical or foam-type fire extinguisher.
WARNING: To reduce the risk of fire,
electrical shock, or injury to persons, observe the
following:
A. Use this unit only in the manner intended
by the manufacturer. If you have questions,
contact the manufacturer.
B. Before servicing or cleaning the unit,
switch power off at service panel.
C. When cutting or drilling into wall or
ceiling do not damage electrical wiring
and other hidden utilities.
D. Ducted fans must always be vented to
the outdoors.
E. To reduce the risk of fire, use only metal
ductwork.
F. Do not flame foods on the cooktop. If you
do flame foods under the hood, turn the
fan on.
WARNING: To reduce the risk of a
cooktop grease fire:
A. Keep fan, filters and grease-laden surfaces
clean.
B. Always turn vent ON when cooking at
high heat.
C. Use high settings on cooktop only when
necessary. Heat oil slowly on low to
medium setting.
D. Don’t leave the cooktop unattended
when cooking.
E. Always use cookware and utensils
appropriate for the type and amount
of food being prepared.
CAUTION: For general ventilating use
only. Do not use to exhaust hazardous or
explosive materials and vapors.
SAFETY PRECAUTIONS
WARNING: NEVER use this
appliance as a space heater to heat or
warm the room. Doing so may result
in carbon monoxide poisoning and
overheating of the oven.
Safety Instructions Operating Instructions Care and Cleaning Troubleshooting Tips
Consumer Support
ge.com
5
■Avoid scratching the glass cooktop surface.
The glass surface can be scratched with
items such as sharp instruments, rings or
other jewelry and rivets on clothing.
■Large scratches or impacts to glass
cooktops can lead to broken or shattered
glass.
■Do not operate the cooktop if the glass is
broken. Spillovers or cleaning solution may
penetrate a broken cooktop and create a
risk of electrical shock. Contact a qualified
technician immediately should your glass
cooktop surface become broken.
■Never use the glass cooktop surface as a
cutting board.
■Do not place or store items that can melt
or catch fire on the glass cooktop surface,
even when it is not being used.
■Be careful when placing spoons or other
stirring utensils on glass cooktop surface
when it is in use. They may become hot
and could cause burns.
■Clean the cooktop surface with caution.
If a wet sponge or cloth is used to wipe
spills on a hot surface, be careful to avoid
steam burns. Some cleaners can produce
noxious fumes if applied to a hot surface.
NOTE: We recommend that you avoid
wiping any surface areas until they have
cooled and the indicator light has gone
off. Sugar spills are the exception to this.
Please see Cleaning the glass cooktop
surface section.
■When the cooktop is cool, use only
CERAMA BRYTE®Ceramic Cooktop
Cleaner and the CERAMA BRYTE®
Cleaning Pad to clean the cooktop.
■To avoid possible damage to the cooking
surface, do not apply cleaning cream to the
glass surface when it is hot.
■After cleaning, use a dry cloth or paper
towel to remove all cleaning cream residue.
■Read and follow all instructions and
warnings on the cleaning cream labels.
Use care when touching the glass cooktop surface. The glass surface of the cooktop will retain heat
after the controls have been turned off.
GLASS COOKTOP SURFACE (on some models)
Safety Instructions Operating Instructions Care and Cleaning Troubleshooting Tips
Consumer Support
This cooktop leaves the factory set for use with natural gas.
If you want to convert to LP gas, the conversion must be performed by a qualified LP gas
installer.
The conversion instructions, conversion sticker and LP orifices can be found attached to the
cooktop next to the pressure regulator.
There is a second set of instructions included in the envelope containing the product wiring
diagrams on the side of the cooktop. Keep these instructions and the orifices in case you want
to convert back to natural gas.
■Do not leave plastic items on the cooktop—
they may melt if left too close to the vent.
■Keep all plastics away from the surface
burners.
■If you smell gas, turn off the gas to the
cooktop and call a qualified service
technician. Never use an open flame to
locate a leak.
■To avoid the possibility of a burn, always be
certain that the controls for all burners are
at the off position and all grates are cool
before attempting to remove them.
■Never clean the cooktop surface when it is
hot. Some cleaners produce noxious fumes
and wet cloths could cause steam burns if
used on a hot surface.
■Never leave jars or cans of fat drippings
on or near your cooktop.
■Do not use aluminum foil under burner
grates. Misuse could result in a fire hazard
or damage to the cooktop.
■Do not cover or block the area around
the cooktop knobs. This area must be kept
clear for proper ventilation and burner
performance.
■Clean only parts listed in this Owner’s
Manual.
CONVERTING TO LP GAS (or converting back to natural gas from LP)
ge.com
Adjust the burner flame size so it does not extend beyond the edge of the cookware. Excessive flame
is hazardous.
SURFACE BURNERS
Cook meat and poultry thoroughly—meat to at least an INTERNAL temperature of 160°F and poultry to at least
an INTERNAL temperature of 180°F. Cooking to these temperatures usually protects against foodborne illness.
COOK MEAT AND POULTRY THOROUGHLY…
7
READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.
SAVE THESE INSTRUCTIONS
8
Safety InstructionsOperating InstructionsCare and CleaningTroubleshooting TipsConsumer Support
Features of your cooktop.
Throughout this manual, features and appearance may vary from your model.
1
43
97
6
5
Explained
Feature Index on page
Vent Grille 12
Vent Filter (located under the vent grille) 12
Simmer Spillproof Burner 9, 11
Spillproof Burners 9, 11
High Power Spillproof Burner 9, 11
Vent Control 10
Surface Burner Controls 9
Glass Cooktop Surface 13, 14
Cast-Iron Burner Grates 12
Vent Grille Gasket 12, 13, 14
2
8
1
2
3
4
5
6
7
8
9
4
9
10
10
Before Lighting a Gas Burner
■Make sure all grates on the cooktop
are in place before using any burner.
After Lighting a Gas Burner
■Do not operate the burner for an
extended period of time without
cookware on the grate. The finish
on the grate may chip without
cookware to absorb the heat.
■Be sure the burners and grates are
cool before you place your hand,
a pot holder, cleaning cloths or
other materials on them.
Safety Instructions Care and Cleaning Troubleshooting TipsOperating Instructions
Consumer Support
9
Using the gas surface burners. ge.com
Throughout this manual, features and appearance may vary from your model.
How to Light a Gas Surface Burner
Push the control knob down and turn it
to the LITE position.
You will hear a little clicking noise—the
sound of the electric spark igniting the
burner.
Turn the knob to adjust the flame size.
If the knob stays at LITE, it will continue
to click.
When one burner is turned to LITE,
all the burners spark. Do not attempt to
disassemble or clean around any burner
while another burner is on. An electric
shock may result, which could cause you
to knock over hot cookware.
Push the control knob down and
turn it to the LITE position.
How to Select Flame Size
For safe handling of cookware, never let the flames
extend up the sides of the cookware.
Watch the flame, not the knob, as you
reduce heat. The flame size on a gas
burner should match the cookware you
are using.
Any flame larger than the bottom of the
cookware is wasted and only serves to
heat the handle.
In Case of Power Failure
In case of a power failure, you can light
the gas surface burners on your cooktop
with a match. Hold a lit match to the
burner, then push in and turn the control
knob to the position. Use extremeLITE
caution when lighting burners this way.
Surface burners in use when an electrical
power failure occurs will continue to
operate normally.
IN CASE OF A POWER FAILURE, THE
VENTILATION SYSTEM WILL NOT OPERATE.
Sealed Gas Burners
The smaller burner (right rear position)
will give the best simmer results. It offers
precise cooking performance for delicate
foods, such as sauces or foods which need
to cook over low heat for a long time.
It can be turned down to a very low
simmer setting.
The other burners are higher powered
and will bring liquids to a boil quicker,
especially with the use of a lid.
OFF
MED
HI
LO
Safety InstructionsOperating InstructionsCare and CleaningTroubleshooting TipsConsumer Support
10
Wok This Way
We recommend that you use a flat-bottomed
wok, available at your local retail store.
Only a flat-bottomed wok should be used.
Do not use a flat-bottomed wok with a
wok holder.
Do not use a flat-bottomed wok on a
support ring. Placing the ring over the
burner or grate may cause the burner to
work improperly, resulting in carbon
monoxide levels above allowable current
standards. This could be dangerous to
your health.
Use a flat-bottomed wok.
Cookware
Aluminum: Medium-weight cookware is
recommended because it heats quickly
and evenly. Most foods brown evenly in
an aluminum skillet. Use saucepans with
tight fitting lids when cooking with
minimum amounts of water.
Enamelware: Under some conditions,
the enamel of some cookware may
melt. Follow cookware manufacturer’s
recommendations for cooking methods.
Glass: There are two types of glass
cookware: those for oven use only
and those for cooktop cooking
(saucepans, coffee and tea pots).
Glass conducts heat very slowly.
Cast Iron: If heated slowly, most
skillets will give satisfactory results.
Heatproof Glass-Ceramic: Can be used
for either surface or oven cooking.
It conducts heat very slowly and cools
very slowly. Check cookware
manufacturer’s directions to be sure it
can be used on a gas cooktop.
Stainless Steel: This metal alone has
poor heating properties and is usually
combined with copper, aluminum
or other metals for improved heat
distribution. Combination metal skillets
usually work satisfactorily if they are used
with medium heat as the manufacturer
recommends.
Using your cooktop.
Stove Top Grills
Do not use stove top grills on your
sealed gas burners. If you use the stove
top grill on the sealed gas burner it will
cause incomplete combustion and can
result in exposure to carbon monoxide
levels above allowable current
standards. This can be hazardous to
your health.
How to Operate the Downdraft Vent System
The built-in vent system helps remove
cooking vapors, odors and smoke from
foods prepared on the cooktop.
Turn the vent fan speed control knob
to orHI, MED LO, as needed.
Continuous use of the vent system
while cooking helps keep the kitchen
comfortable and less humid, reducing
cooking odors and soiling moisture
that normally creates a frequent need
for cleaning.
The appearance of the burner flames
may be affected when the vent fan is
operating. At high fan speed setting,
the flame may be drawn toward the
vent opening, affecting cooking
performance.
IN CASE OF A POWER FAILURE, THE
VENTILATION SYSTEM WILL NOT OPERATE.
Using the downdraft vent system.
Safety Instructions Operating Instructions Troubleshooting TipsCare and Cleaning
Consumer Support
Care and cleaning of the cooktop. ge.com
Be sure electrical power is off and all surfaces are cool before cleaning any part of the cooktop.
Sealed Burner Assemblies
Turn all controls OFF before removing
the burner parts.
The burner grates, caps and burner
heads can be lifted off, making them
easy to clean.
When one burner is turned to
LITE, all the burners spark. Do not
attempt to disassemble or clean
around any burner while another
burner is on. An electric shock
may result, which could cause you
to knock over hot cookware.
Burner Caps and Heads
Burner Caps
Lift off when cool. Wash burner caps
in hot, soapy water and rinse with clean
water. You may scour with a plastic
scouring pad to remove burned-on
food particles.
Burner Heads
The slits in the burner heads of your cooktop
must be kept clean at all times for an even,
unhampered flame.
You should clean the surface burners
routinely, especially after bad spillovers,
which could clog these openings. Lift off
when cool.
To remove burned-on food, soak the
burner heads in a solution of mild
liquid detergent and hot water for
20–30 minutes. For more stubborn stains,
use a toothbrush.
After Cleaning
Before putting the burner caps and
heads back, shake out excess water and
then dry them thoroughly by setting in
a warm oven for 30 minutes.
Replacement
The burner heads and burner bases are
labeled A, B and C to aid reassembly.
Replace the burner heads on the bases
matching the letters. Replace the caps on
the heads. Make sure that the caps and
heads are replaced in the correct location.
There is one small (A), two medium (B)
and one large (C) head and cap.
NOTE: Before removing the burner caps
and heads, remember their size and location.
Replace them in the same location after
cleaning. The burner heads and burner bases
are labeled A, B and C to aid reassembly.
CAUTION: Do not operate the
burner without all burner parts in
place.
After cleaning, make sure the
notch in the burner head is
positioned toward the electrode.
Rotate the burner head around the
burner base until it is level and
securely seated.
Grate
Electrode
Burner head
Burner cap
Electrode
Burner base
B
B A
C
B
B
A
C
Medium
Head
and Cap
Medium
Head
and Cap
Small
Head
and Cap
Large
Head
and Cap
Front of Cooktop
11
Vent Filter and Chamber
Remove the vent grille and vent grille
gasket. The filter is held in place at an
angle with a hold bump. Lift the filter
up and out of the vent opening
diagonally.
Clean the filter by swishing it in hot,
soapy water. Rinse well and dry
thoroughly.
Do not operate the vent without the filter
in place.
To clean the vent chamber, use hot, soapy
water. Do not use abrasive cleaners; they
will damage the finish.
Replacement
Replace the filter after it is cleaned and
dry. Replace the vent grille gasket by
forming it around the vent opening and
make sure the word “FRONT” is toward
the knobs. Replace the grille.
Care and cleaning of the cooktop.
12
Safety InstructionsOperating InstructionsCare and CleaningTroubleshooting TipsConsumer Support
Burner Grates and Vent Grille
Lift off when cool. Grates and grille
should be washed regularly and, of
course, after spillovers. Wash them in hot,
soapy water and rinse with clean water.
Discoloration on the grates may also be
removed by using the provided cooktop
cleaning cream. Apply a drop or two on a
damp cloth and rub across the discolored
area. Rinse and dry. After cleaning,
replace the burner grates and make
sure they are positioned securely over
the burners.
To remove burned-on food, use a soap-
filled scouring pad.
Although they are durable, the grates will
gradually lose their shine, regardless of
the best care you can give them. This is
due to their continual exposure to high
temperatures. You will notice this sooner
with lighter color grates.
Do not operate a burner for an extended
period of time without cookware on the
burner grate. The finish on the grate may
chip without cookware to absorb the heat.
Replacement
Before replacing the vent grille, make
sure the grille gasket is properly installed
around the downdraft vent opening, with
the word “FRONT” toward the knobs.
Replace the vent grille carefully over
the gasket.
When replacing the grates, make sure
they are positioned with their brass
locator feet toward the center.
NOTE: Do not clean the grates, grille or grille
gasket in a self-cleaning oven.
The grates, grille and grille gasket may be
cleaned in a dishwasher.
Appearance may vary.
FRONT
Vent
Chamber
Remove and replace the filter diagonally through
the vent opening.
When replacing the filter, make sure it rests, at an
angle, on the supports in the vent opening.
Grille
Vent Grille
Gasket
Vent Filter
The grate legs have one brass foot
and three rubber feet. To order
replacement rubber grate feet,
please call our toll-free number:
National
Parts Center . . . . . . . . . 800.626.2002
Rubber Grate Feet . . #WB02T10101
To order replacement filters, please
call our toll-free number:
National
Parts Center . . . . . . . . . 800.626.2002
Filter . . . . . . . . . . . . . . #WB02X10651
Grille
Vent Grille Gasket
Vent Filter
Brass
Locator Feet
Burned-On Residue
WARNING: DAMAGE to your glass surface
may occur if you use scrub pads other than
the pad included with your cooktop.
Allow the cooktop to cool.
Remove the burner grates, vent
grille and vent grille gasket.
Spread a few drops of CERAMA
BRYTE®Ceramic Cooktop Cleaner
to the entire burned residue area.
Using the included CERAMA
BRYTE®Cleaning Pad for Ceramic
Cooktops, rub the residue area,
applying pressure as needed.
If any residue remains, repeat the
steps listed above as needed.
For additional protection, after all
residue has been removed, polish
the entire surface with CERAMA
BRYTE®Ceramic Cooktop Cleaner
and a paper towel.
Use a CERAMA BRYTE®Cleaning
Pad for Ceramic Cooktops or a
Scotch-Brite®Multi-Purpose No
Scratch blue scrub pad.
The control knobs may be removed for easier
cleaning.
Make sure the knobs are in the OFF
positions and pull them straight off the
stems for cleaning.
The knobs can be cleaned in a
dishwasher or they may also be washed
with soap and water. Make sure the
insides of the knobs are dry before
replacing.
Replace the knobs in the OFF position
to ensure proper placement.
13
Safety Instructions Operating Instructions Troubleshooting TipsCare and Cleaning
Consumer Support
Control Knobs
Flat
Molded flat area
The control knobs may be removed
for easier cleaning.
ge.com
Normal Daily Use Cleaning
ONLY use CERAMA BRYTE®Ceramic
Cooktop Cleaner on the glass cooktop.
Other creams may not be as effective.
To maintain and protect the surface of
your glass cooktop, follow these steps:
Before using the cooktop for the
first time, clean it with CERAMA
BRYTE®Ceramic Cooktop Cleaner.
This helps protect the top and
makes clean-up easier.
Daily use of CERAMA BRYTE®
Ceramic Cooktop Cleaner will help
keep the cooktop looking new.
Remove the burner grates, vent
grille and vent grille gasket.
Shake the cleaning cream well.
Apply a few drops of CERAMA
BRYTE®Ceramic Cooktop Cleaner
directly to the cooktop.
Use a paper towel or CERAMA
BRYTE®Cleaning Pad for Ceramic
Cooktops to clean the entire
cooktop surface.
Use a dry cloth or paper towel
to remove all cleaning residue.
No need to rinse.
NOTE: It is very important that you DO NOT
heat the cooktop until it has been cleaned
thoroughly.
Clean your cooktop after
each spill. Use CERAMA
BRYTE®Ceramic Cooktop
Cleaner.
Cleaning the glass cooktop.
14
Safety InstructionsOperating InstructionsCare and CleaningTroubleshooting TipsConsumer Support
The CERAMA BRYTE®Ceramic
Cooktop Scraper and all
recommended supplies are
available through our Parts Center.
See instructions under “To Order
Parts” section below.
NOTE: Do not use a dull or
nicked blade.
Heavy, Burned-On Residue
Allow the cooktop to cool.
Remove the burner grates, vent
grille and vent grille gasket.
Use a single-edge razor blade
scraper at approximately a 45°
angle against the glass surface and
scrape the soil. It will be necessary
to apply pressure to the razor
scraper in order to remove the
residue.
After scraping with the razor
scraper, spread a few drops of
CERAMA BRYTE®Ceramic
Cooktop Cleaner to the entire
burned residue area. Use the
CERAMA BRYTE®Cleaning Pad
to remove any remaining residue.
For additional protection, after all
residue has been removed, polish
the entire surface with CERAMA
BRYTE®Ceramic Cooktop Cleaner
and a paper towel.
Cleaning the glass cooktop.
Turn off all surface burners and,
with an oven mitt, remove hot
pans and grates.
Wearing an oven mitt:
a. Use a single-edge razor blade
scraper (CERAMA BRYTE®
Ceramic Cooktop Scraper) to
move the spill to a cool area
on the cooktop.
b. Remove the spill with
paper towels.
Any remaining spillover should be
left until the surface of the cooktop
has cooled.
Don’t use the surface units again
until all of the residue has been
completely removed.
NOTE: If pitting or indentation in the glass
surface has already occurred, the cooktop
glass will have to be replaced. In this case,
service will be necessary.
Damage from Sugary Spills and Melted Plastic
Our testing shows that if
you are cooking high sugar
mixtures such as jelly or
fudge and have a spillover,
it can cause permanent
damage to the glass surface
unless the spillover is
immediately removed.
Be careful not to slide pots and pans
across your cooktop. It will leave metal
markings on the cooktop surface.
These marks are removable using
the CERAMA BRYTE®Ceramic
Cooktop Cleaner with the CERAMA
BRYTE®Cleaning Pad for Ceramic
Cooktops.
WARNING: Carefully check the bottom
of pans for roughness that would scratch
the cooktop.
Metal Marks and Scratches
To order CERAMA BRYTE®Ceramic
Cooktop Cleaner and the cooktop
scraper, please call our toll-free number:
National Parts Center 800.626.2002
CERAMA BRYTE®
Ceramic Cooktop Cleaner . . . .# WX10X300
CERAMA BRYTE®
Ceramic Cooktop Scraper . .# WX10X0302
Kit . . . . . . . . . . . . . . . . . . . . . .# WB64X5027
(Kit includes cream and razor scraper)
CERAMA BRYTE®Cleaning Pads for
Ceramic Cooktops . . . . . . . . . . .#WX10X350
To Order Parts
Glass surface—potential for permanent damage.
IMPORTANT SAFETY INSTRUCTIONS
The cooktop has been design certified by CSA
International. As with any appliance using gas and
generating heat, there are certain safety precautions
you should follow. You’ll find these precautions in the
Important Safety Information section in the front of
this Owner’s Manual. Read them carefully.
•Be sure your cooktop is installed properly by a
qualified installer or service technician.
•The cooktop must be electrically grounded in
accordance with local codes, or in their absence,
with the National Electrical Code ANSI/NFPA
No. 70 – Latest Edition.
•Installation of this cooktop must conform with local
codes, or in the absence of local codes, with the
National Fuel Gas Code ANSI Z223.1 – Latest Edition.
•Improper installation, adjustment, alteration,
service or maintenance can cause injury or property
damage. Refer to this manual. For assistance or
additional information, consult a qualified installer,
service agency, manufacturer (dealer) or the gas
supplier.
•Disconnect electrical supply before servicing.
•Never reuse old flexible connectors. The use of old
flexible connectors can cause gas leaks and personal
injury. Always use flexible connectors whenNEW
installing a gas appliance.
•Make sure the wall coverings around the cooktop can
withstand heat generated by the cooktop up to 200°F.
•Avoid placing cabinets above the cooktop.
•If cabinets are placed above the cooktop, allow a
minimum clearance of 30 between the cooking ″
surface and the bottom of unprotected cabinets.
•If cabinets are placed above the cooktop, use
cabinets no more than 13″deep.
•If a 30″clearance between cooking surface and
overhead combustible material or metal cabinets
cannot be maintained, protect the underside of the
cabinets above the cooktop with not less than 1/4″
insulating millboard or gypsum board at least 3/16″
thick covered with 28 gauge sheet steel or 0.020″
thick copper.
•Clearance between the cooking surface and protected
cabinets MUST NEVER BE LESS THAN 24.″The
vertical distance from the plane of the cooking
surface to the bottom of adjacent overhead cabinets
extending closer than 1″to the plane of the cooktop
sides must not be less than 18.″
FOR YOUR SAFETY
If You Smell Gas:
1. Open windows.
2. Don’t touch any electrical switches.
3. Extinguish any open flame.
4. Immediately call your gas supplier.
Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any other
appliance.
IN THE COMMONWEALTH OF MASSACHUSETTS:
•This product must be installed by a licensed
plumber or gas fitter.
•When using ball-type gas shut-off valves, they
shall be the T-handle type.
•A flexible gas connector, when used, must not
exceed 3 feet.
Installation
Gas Downdraft
Instructions
Cooktop
If you have questions, call 800.GE.CARES (800.432.2737) or visit our Website at: ge.com
Read these instructions completely and carefully.
• IMPORTANT –Save these instructions
for local inspector’s use.
•IMPORTANT –Observe all governing
codes and ordinances.
• Note to Installer – Be sure to leave these
instructions with the Consumer.
• Note to Consumer – Keep these instructions for
future reference.
• Unless very knowledgeable in the installation of
this product, engage a professional installer.
• Proper installation is the responsibility of the
installer.
• Product failure due to improper installation is
not covered under the Warranty.
BEFORE YOU BEGIN
WARNING –Before beginning the
installation, switch power off at the service panel
and lock the service disconnecting means to
prevent power from being switched on accidentally.
When the service disconnecting means cannot be
locked, securely fasten a prominent warning device,
such as a tag, to the service panel.
15
B
B
C
A
Hold-Down
Retainers and
Screws
Vent Grille
Cleaning
Cream
Scrub Sponge
Sheet Metal
Screws (9)
(8-18 x 3/8″)
CAUTION: GLASS
IS FRAGILE
DO NOT BUMP EDGE
OF GLASS DURING
INSTALLATION
Foam Gasket Tape Vent Grille Gasket
16
Burner
Grate
(2)
Regulator
Blower Assembly and
(4) Mounting Nuts
(10-32 keps – nuts with
lock washers attached)
Blower
Plenum
Vent
Filter
Installation Instructions
UNPACKING YOUR COOKTOP
•Blower assembly
•Blower plenum
•(4) Nuts (10-32 keps – nuts
with lock washers attached)
•(2) Hold-down retainers and
thumb screws
•(9) Sheet metal screws
(8-18 x 3/8″)
•Foam gasket tape (9-ft. roll)
•Vent grille
•Vent filter
•Vent grille gasket
•Cleaning cream
•Scrub sponge or scraper
(on some models)
•Burner grates
•Burner heads
(1 small (A), 2 medium (B),
1 large (C))
•Burner caps
(1 small, 2 medium, 1 large)
•Gas pressure regulator
•Attached 120-volt grounded
plug cord
•LP Conversion
•Reflective tape
PARTS INCLUDED (PACKED BELOW THE COOKTOP)
CAUTION:
DO NOT LIFT
FROM VENT
OPENING
Burner Caps and Burner Heads
Burner Cap and Burner Head Burner Cap and Burner Head
Reflective
Tape
17
TOOLS AND MATERIALS
YOU WILL NEED
•Saw
•Duct tape
•Measuring tape or scale
•Carpenter’s square
•Adjustable wrench or socket set (7/16″socket and
ratchet)
•Drill and drill bit
•1/4″nut driver
•Sheet metal screws
•Pipe wrench
•Manual gas line shut-off valve
•Pipe joint sealant that resists action of LP gas
•Ductwork to suit the installation
For rigid connection:
•Shut-off valve
•Union
•Pipe fittings as required
For flexible connection where local codes permit:
•Flexible metal tubing (same 3/4″ ″or 1/2 I.D. as gas
supply line)
217⁄8″
201⁄2″
22″
297⁄8″
21⁄4″
283⁄4″
30″COOKTOP (DIMENSIONS FOR REFERENCE ONLY)
Unit shown fully assembled.
Unit must be vented to the outside!
Installation Instructions
PREPARATION
18
Installation Instructions
CABINET PREPARATION
PREPARING FOR INSTALLATION
Positioning the cooktop
The cooktop is designed to look best when centered
in a cabinet at least 30″wide.
The exhaust vent beneath the cooktop must be
located between wall studs or floor joists so that the
ductwork may be installed properly.
The downdraft system with blower, motor and
ductwork will occupy the cabinet below the cooktop.
Drawers cannot be installed below this cooktop.
Avoid placing cabinets above the cooktop unit, if
possible, in order to reduce the hazards caused by
reaching over heated surface units.
If the cabinetry is used above the cooktop, allow a
minimum 30″clearance between the cooking surface
and the bottom of the unprotected cabinet.
If the clearance between the cooktop and the
cabinetry is less than 30″, the cabinet bottom must
be protected with a flame retardant millboard at least
1/4″thick, or gypsum board at least 3/16″thick,
covered with 28 gauge sheet steel or 0.020″thick
copper. Clearance between the cooktop and the
protected cabinetry MUST NEVER BE LESS
THAN 24 ″.
EXCEPTION: Installation of a listed microwave oven
or cooking appliance over the cooktop shall conform
to the installation instructions packed with that
appliance.
Working areas adjacent to the cooktop should have
an 18 minimum clearance between the countertop″
and the bottom of the cabinet. If the clearance is less
than 18″, the adjacent cabinets should be at least 5″
from the side edge of the cooktop.
13 max.″
depth of
unprotected
overhead
cabinets
5″min.
clearance from
cutout to side
walls
30 min.″
clearance from
countertop
to unprotected
overhead surface
18″min. height
from countertop
to nearest cabinet
on either side of
the unit
11⁄2″min.
1PREPARING THE BASE CABINET
This cooktop is designed to fit easily into a
variety of cabinets. However, the combined
installation of a downdraft vent and a cooktop
require careful consideration.
Some cabinets may require modifications.
This installation requires a 24″min. deep
cabinet base. The cabinet must be at least
30 wide.″
Preparing a cabinet that is against a wall
In some cabinets, the sides may need to be
scooped or cut down 53⁄4″as shown, and the
corner braces removed in order to
accommodate the unit.
In 75 cm and 90 cm frameless European
cabinets, the back panel may need to be cut
down 53⁄4″to accommodate the unit.
Preparing a peninsula or island-type cabinet
In a peninsula or island type cabinet, the
sides may need to be scooped or cut down,
and the corner braces removed in order to
accommodate the unit.
53⁄4″
Approx.
53⁄4″Approx.
for
European
cabinets
2
PREPARING THE COUNTERTOP
The countertop must have a deep flat surface
to accommodate the cooktop and the vent.
Countertops with a rolled front edge and
backsplash may not provide the flat surface
area required.
Clearance between inside front of cabinet and
rear of countertop cutout must be 205⁄8″in
order to accommodate cooktop depth.
A 1/2″wide flat area is required around the
edge of opening for support of the unit. The
cooktop unit must be level and sit squarely
into countertop opening.
Carefully cut countertop opening according
to the dimensions shown in the illustration.
Be sure that opening is cut squarely, with
sides parallel to each other and rear exactly
perpendicular to sides.
PREPARING FOR DUCTWORK
NOTE: Ductwork MUST be vented to outside.
DO NOT vent into a wall, ceiling, crawlspace, attic or
any concealed space.
Cut hole in cabinet wall or floor as appropriate for
your installation. Make sure exhaust duct is located
between wall studs or floor joists.
NOTE: When cutting or drilling into wall or ceiling,
do not damage electrical wiring and other hidden
utilities.
205⁄8″
17⁄8″Min.
205⁄8″
17
⁄8″Min.
25″287⁄8″
91⁄8″
183⁄4″
101⁄8″
61⁄8″
Back Venting
(Requires 31⁄ )4″x 10″
Rear Wall Venting Downward Venting
3
BLOWER TO DUCTWORK ALIGNMENT
In general, the use of flexible ducting is discouraged
because it can cause severely restricted airflow.
However, if the blower outlet and the floor or wall
duct location do NOT align well, then flexible METAL
ducting can be used to adapt to an offset. Good
alignment without use of flexible ducting is best.
NOTE:
•Do not exceed the maximum recommended
offset of 6″.
•Do not allow the flexible ducting to kink or collapse.
•Do stretch the flexible ducting as much as possible
to eliminate as much of the corrugation as possible.
4
5
23⁄8″Min.
A 31
⁄4″ ″ ″x 10 rectangle to 6 round transition duct is
available at your local building supply store.
NOTE: Illustrations are for planning purposes only
.
Bottom Venting
6″Max.
Centerline
to
Centerline
Offset
Installation Instructions
CABINET PREPARATION CUTOUTS
19
20
Installation Instructions
DUCTWORK CALCULATIONS
Calculate Total Equivalent Ductwork Length
Equivalent Number Equivalent
Duct Pieces Length* x Used = Length
6″round
straight 1 ft. x ( )†= ft.
31⁄4″x 10″
straight 1 ft. x ( )† = ft.
6″, 90°
elbow 15 ft. x ( ) = ft.
6″, 45°
elbow 9 ft. x ( ) = ft.
24 max. ″
flexible
metal offset
adapter 34 ft. x ( ) = ft.
31⁄4″x 10″
90° elbow 16 ft. x ( ) = ft.
31⁄4″x 10″
45° elbow 5 ft. x ( ) = ft.
31⁄4″x 10″
90° flat elbow
18 ft. x ( ) = ft.
6″round
to 31⁄4″x 10″
transition 7 ft. x ( ) = ft.
Subtotal Column 1 = ft.
*Equivalent lengths of duct pieces are based on
actual tests and reflect requirements for good
venting performance with any downdraft cooktop.
†Measure and list feet of straight duct used. Count
and list the quantity of all other duct pieces for the
“Number Used” of each type.
IMPORTANT:
For maximum efficiency, use the shortest and
straightest duct run possible, with as few fittings
as possible. For satisfactory performance, the duct
run should not exceed 100 feet equivalent length.
Venting performance is improved by using larger
diameter duct.
Equivalent Number Equivalent
Duct Pieces Length* x Used = Length
6″round
to 31⁄4″x 10″
transition
90° elbow 20 ft. x ( ) = ft.
31⁄4″x 10″
to 6″round
transition 5 ft. x ( ) = ft.
31⁄4″x 10″
to 6″round
transition
90° elbow 12 ft. x ( ) = ft.
6″round
wall cap
with damper 21 ft. x ( ) = ft.
31⁄4″x 10″
wall cap
with damper 27 ft. x ( ) = ft.
6″round
roof cap 20 ft. x ( ) = ft.
6″round
roof vent 24 ft. x ( ) = ft.
Subtotal Column 2 = ft.
Subtotal Column 1 = ft.
TOTAL DUCTWORK = ft.
Should not exceed 100 feet.
DO NOT use flexible plastic ducting.
Vent installation should not exceed 100 feet
equivalent length.

Termékspecifikációk

Márka: GE
Kategória: sütő
Modell: Profile JGP989BCBB

Szüksége van segítségre?

Ha segítségre van szüksége GE Profile JGP989BCBB, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók sütő GE

GE

GE Profile JGS968TEKWW Útmutató

18 Március 2025
GE

GE Profile PGB910SETSS Útmutató

18 Március 2025
GE

GE JBS08PICWW Útmutató

14 Január 2025
GE

GE Profile JP939CHCC Útmutató

13 Január 2025
GE

GE JSP26BDWH Útmutató

13 Január 2025
GE

GE Profile JBP99SHSS Útmutató

13 Január 2025
GE

GE 169140 Oven Útmutató

13 Január 2025
GE

GE Profile Spectra JB940TDWW Útmutató

13 Január 2025
GE

GE JB695DFWW Útmutató

12 Január 2025
GE

GE Profile PSB9100SVSS Útmutató

28 December 2024

Útmutatók sütő

Legújabb útmutatók sütő

Whirlpool

Whirlpool akp 234 na 02 Útmutató

10 Április 2025
Candy

Candy FCP405X Útmutató

10 Április 2025
Premiere

Premiere EBC 23558 E Útmutató

10 Április 2025
Gram

Gram KKI 8544-90 T Útmutató

10 Április 2025
KitchenAid

KitchenAid KHDD2 38510 Útmutató

10 Április 2025
Stoves

Stoves Richmond 1000DFT Útmutató

10 Április 2025
Küppersbusch

Küppersbusch EEH615.0 Útmutató

10 Április 2025
Ariston

Ariston FM 51 Útmutató

10 Április 2025
Siemens

Siemens HB23A1520S Útmutató

9 Április 2025
Whirlpool

Whirlpool akp 237 Útmutató

9 Április 2025