Használati útmutató GE JX1830AB

GE Magnetron JX1830AB

Olvassa el alább 📖 a magyar nyelvű használati útmutatót GE JX1830AB (4 oldal) a Magnetron kategóriában. Ezt az útmutatót 3 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/4
PART QUANTITY
Trim Frame 1
Bottom Duct 1
Side Duct 1
1” Screws 6
(4 required, 2 extra)
1/2” Screws 15
(11 required, 4 extra)
Anti-Tip Bracket 1
Bottom Bracket 1
Upper Duct 1
Template 1
PARTS INCLUDED
Questions? Call GE Answer Center at 800.626.2000
or Visit our Website at:
www.GEAppliances.com
READ CAREFULLY.
KEEP THESE INSTRUCTIONS.
Installation Built-In Trim Kits
Instructions
JX1827 and JX1830
Read these instructions completely and carefully.
•IMPORTANT –Save these
instructions for local inspector’s use.
•IMPORTANT –Observe all
governing codes and ordinances.
•Note to Installer –Be sure to leave these
instructions with the Consumer.
•Note to Consumer –Keep these
instructions for future reference.
BEFORE YOU BEGIN
• Unplug the microwave oven before attempting
installation of this kit.
• Skill level – Installation of this appliance requires basic
mechanical and electrical skills.
• Completion time – 1-3 hours
• Proper installation is the responsibility of the installer.
• Product failure due to improper installation is not
covered under the Warranty.
• This kit is UL listed for installation alone or over any
General Electric/Hotpoint/RCA single electric wall
oven.
TOOLS YOU WILL NEED
Phillips screwdriver
Pencil
Tape measureAwl or punch
Drill with 7⁄64″bit or #35
1
FOR YOUR SAFETY:
WARNING –Before beginning the
installation, switch power off at service panel and lock
the service disconnecting means to prevent power
from being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten
a prominent warning device, such as a tag, to the
service panel.
2
CUTOUT DIMENSIONS1.
* Min. depth with receptacle outside cabinet 191⁄2″
Min. depth with receptacle inside cabinet 22″
Installation Instructions
Models 27″ ″30
Height 163⁄ 164″3⁄4″
Width 251⁄ 252″1⁄2″
Depth (min.)* 191⁄ 192″or 22″1⁄2″or 22″
On 27 models, allow 1 at the top, ″ ″ 11⁄16″on the sides
and 13⁄8″at the bottom for overlap of the Trim Frame
over the edges of the cutout.
On 30 models, allow 1 at the top, 2″ ″ 3⁄16″on the sides
and 13⁄8″at the bottom for overlap of the Trim Frame
over the edges of the cutout.
Depth
Height
3 Min.″
Width
INSTALL BOTTOM BRACKET
AND BOTTOM DUCT
2.
Disconnect the microwave oven before proceeding
with the installation.
Fasten the bottom bracket to the bottom duct by
using two 1⁄2″screws.
Remove any loose items inside the microwave
oven, including the turntable and turntable
support. Carefully turn the microwave upside
down.
Install bottom duct with four 1⁄2″screws as shown.
A
C
B
D
Front
Rear
1⁄2″Screws (2)
Screws
Screws
Microwave Oven Upside Down
3
Installation Instructions
INSTALL THE ANTI-TIP BRACKET3.
Fold or cut the front edge of the template, along
the front guide line. Place the template flush along
the front edge of the cutout floor, aligning the
center line of the template with the center line of
the cutout floor. Mark the center positions with an
awl or center punch for the anti-tip bracket
location as shown.
Remove the template and drill two holes for the
anti-tip bracket.
Install the anti-tip bracket onto the cutout floor
using two 1⁄2″screws.
A
B
C
Cutout Floor
1⁄2″Screws (2)
Anti-Tip Bracket
INSTALL SIDE DUCT AND UPPER
DUCT
4.
Connect the side duct to the upper duct as shown.
1. Insert projecting tabs of the upper duct into the
holes of the side duct.
2. Bend the tabs up with caution as shown.
NOTE: Remove any oil or dirt on the surface of the
microwave oven before the ducts are attached.
Set the microwave upright, being careful not to
bend the front flange. Remove the one existing
screw from the left side of the microwave oven.
Peel off the backing of the double sided tape.
Carefully position the side duct and upper duct
assembly on the microwave cabinet, aligning with
the bottom screw hole. Press down firmly on the
ducts. Fasten the duct assembly to the left side of
the cabinet with the screw removed above.
B
A
(2)
C
Existing Screw (1)
(1)
Upper Duct
Side Duct
3 Tabs
3 Holes

Termékspecifikációk

Márka: GE
Kategória: Magnetron
Modell: JX1830AB

Szüksége van segítségre?

Ha segítségre van szüksége GE JX1830AB, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók Magnetron GE

GE

GE Adora DVM7195DKWW Útmutató

12 Január 2025
GE

GE GCST09U1 Útmutató

10 Január 2025
GE

GE GCST07N1WWW Útmutató

8 Január 2025
GE

GE GCHK07N1WBB Útmutató

8 Január 2025
GE

GE GCHK07N1WWW Útmutató

8 Január 2025
GE

GE GCST07N1WBB Útmutató

8 Január 2025
GE

GE GCHK07N1WSS Útmutató

8 Január 2025
GE

GE Profile PWB7030SVSS Útmutató

7 Január 2025
GE

GE UVM9125STSS Útmutató

31 December 2025
GE

GE PVM9215DFWW Útmutató

30 December 2025

Útmutatók Magnetron

Legújabb útmutatók Magnetron

Whirlpool

Whirlpool at 314 Útmutató

6 Április 2025
Privileg

Privileg PCMF 222220 X Útmutató

6 Április 2025
Koenig

Koenig Microwave 2000 Útmutató

6 Április 2025
Creda

Creda 29032 Útmutató

4 Április 2025
Baumatic

Baumatic BMC460BGL Útmutató

3 Április 2025
Superior

Superior 17MG53V Útmutató

2 Április 2025
Ambiano

Ambiano MD18547 Útmutató

1 Április 2025
Whirlpool

Whirlpool AMW 518 IX Útmutató

1 Április 2025
Junker

Junker JM16GA52 Útmutató

1 Április 2025
Friac

Friac MC2802C Útmutató

1 Április 2025