Használati útmutató GE JV356VAA

GE Páraelszívó JV356VAA

Olvassa el alább 📖 a magyar nyelvű használati útmutatót GE JV356VAA (4 oldal) a Páraelszívó kategóriában. Ezt az útmutatót 4 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF

Oldal 1/4

Use and Care & Installation Guide

Convertible Range Hood

Models: JV356 30″

JV656 36″

Write Down the Model and Serial Numbers.

The Model and Serial Numbers are on a label on the

back wall of the hood and on the Consumer Product

Ownership Registration Card that came with your hood.

Before sending in this card, please write these numbers here:

Model Number

Serial Number

IMPORTANT SAFETY INSTRUCTIONS

Read and save these instructions.

WARNING—TO REDUCE THE RISK OF FIRE,

ELECTRIC SHOCK, OR INJURY TO PERSONS,

OBSERVE THE FOLLOWING:

A. Use this unit only in the manner intended by the

manufacturer. If you have questions, contact the

manufacturer at the address or telephone number

listed in the warranty.

B. Before servicing or cleaning unit, switch power

off at service panel and lock service to prevent

power from being switched on accidentally. When

the service disconnecting means cannot be locked,

securely fasten a prominent warning device, such

as a tag, to the service panel.

C. Installation work and electrical wiring must be done by

qualified person(s) in accordance with all applicable

codes and standards, including fire-rated construction.

D. Sufficient air is needed for proper combustion and

exhausting of gases through the flue (chimney) of fuel-

burning equipment to prevent backdrafting. Follow the

heating equipment manufacturer’s guidelines and safety

standards such as those published by the National Fire

Protection Association (NFPA), and the American

Society for Heating, Refrigeration and Air Conditioning

Engineers (ASHRAE), and the local code authorities.

E. When cutting or drilling into wall or ceiling, do not

damage electrical wiring and other hidden utilities.

F. Ducted fans must always be vented to the outdoors.

G. To reduce the risk of fire, use only metal ductwork.

H. This unit must be grounded.

WARNING—TO REDUCE THE RISK OF A

RANGE TOP GREASE FIRE:

A. Keep fan, filters and grease-laden surfaces clean.

B. Always turn hood ON when cooking at high heat.

C. Don’t leave range unattended when cooking.

D. Use high settings on range only when necessary.

Heat oil slowly on low to medium setting.

E. Always use cookware and utensils appropriate for the

type and amount of food being prepared.

• When flaming foods under the hood, turn the fan on.

WARNING—TO REDUCE THE RISK OF INJURY

TO PERSONS IN THE EVENT OF A RANGE TOP

GREASE FIRE, OBSERVE THE FOLLOWING:

A. SMOTHER FLAMES with a close-fitting lid, cookie

sheet, or metal tray, then turn off the burner. BE

CAREFUL TO PREVENT BURNS. If the flames do

not go out immediately, EVACUATE AND CALL

THE FIRE DEPARTMENT.

B. NEVER PICK UP A FLAMING PAN—You may be

burned.

C. DO NOT USE WATER, including wet dishcloths or

towels—a violent steam explosion will result.

D. Use an extinguisher ONLY if:

1. You know you have a Class ABC extinguisher,

and you already know how to operate it.

2. The fire is small and contained in the area where

it started.

3. The fire department is being called.

4. You can fight the fire with your back to an exit.

*Based on “Kitchen Firesafety Tips” published by NFPA.

CAUTION—For general ventilating use only. Do not use

to exhaust hazardous or explosive materials and vapors.

If You Need Service…

• Do not attempt to repair or replace any part of your

hood unless it is specifically recommended in this

guide. All other servicing should be referred to a

qualified technician.

SAVE THESE INSTRUCTIONS

GE Appliances

164D2966P165-2

Venting

This hood must be vented vertically through

upper cabinets or horizontally through an outside

wall. Ductwork is not included.

Improper duct sizing or restrictive roof caps

reduce air moving capacity and will not provide

enough ventilation for an indoor electric grill.

Indoor electric grills produce more smoke than

normal cooking and require at least 410 CFM to

provide adequate ventilation.

Follow the guidelines for proper duct sizing in the

ducting charts. The venting system mustNOTE:

exhaust to the outside.

Cabinet Height

For most efficient operation, the top of the hood should

be approximately 66 (167.6 cm) from the floor.″

Non-Venting

Follow the instructions under “Vented Installation” for

wiring and mounting. Omit the ductwork preparation.

Install WB13X5008–Charcoal filter pads replaceable.)

Tools Required:

• Drill; 11⁄4″wood bit. • Pliers.

• Flat blade screwdriver. • Pencil, ruler and level.

• Saber saw or keyhole saw.

• Caulking, metal snips, duct tape, ducts (with

elbow and transition, if necessary) and wall cap

or roof caps, as required.

INSTALLATION INSTRUCTIONS

Installing the Range Hood

Determine which direction the vent will be

installed (top or rear).

1. Remove filters and motor/light cover (3 screws).

2. Remove the blower motor by removing the

“packing screw” and the clip on the retainer bar.

Discard the clip and screw.

Unplug the motor from the junction box.

Snap the blower retainer

bar toward the rear of

the hood to release the

blower. Remove the

blower.

3. Remove the junction

box cover.

Remove the selected wiring knockout and duct

knockout from the top or rear of the hood. Use a

at blade screwdriver to cut the tabs.

IMPORTANT: OBSERVE ALL GOVERNING

CODES AND ORDINANCES.

SAVE THESE INSTRUCTIONS FOR THE

LOCAL ELECTRICAL INSPECTOR’S USE.

WARNING: Disconnect power before servicing or cleaning the unit.

Care of Filter Care of Exterior Surfaces Charcoal Filter Pads

(not included)

For greatest eciency the aluminum

lter should be cleaned periodically.

To remove the lter, pull the tab to

the side and then down. Soak it in hot

water and detergent. Rinse and dry

thoroughly before replacing.

Use a mild detergent to clean the hood.

DO NOT use abrasive cleansers.

Lights

This hood has two lights. Do not use

bulbs larger than 75 watts. There are

two light levels. To change light

bulbs, rst remove the lters. It is not

necessary to remove the blower cover.

This lter should be inspected

periodically and, when it becomes

saturated, it should be replaced. There

are no eective means of reactivating

this lter. Order WB13X5008.

Top Vent

Knockout

Snap

lock blower

retainer bar

Vent-less operation discharge vent

HORIZONTAL VENTING

(If the wall cap has a damper, do not install the

damper blade on the hood.)

Attach the damper with the small sheet metal

screws (#8 x 1/4 ).″

Check the damper

for free operation.

Open the damper

blade to

approximately 80

degrees.

Position the blower for horizontal discharge. The

air ow arrow on the blower should point to the

rear vent opening.

When the blower is in position, snap the blower

retainer bar toward the front into the indent.

Reattach the plug into the junction box.

8. Lift the hood into position and feed the house

wiring through the wiring knockout.

Slide the hood back against the wall.

Tighten the mounting screws. Be sure the screw

heads are in the narrow neck of the keyhole slot.

9. Complete the electrical wiring in the wiring

box according to National Electrical Code and

local codes.

NOTE: This hood must be permanently

grounded.

10. Replace the junction box cover and blower

assembly.

Reattach the plug into the junction box.

Install light bulbs (not supplied with the hood).

Reattach bottom motor/light cover and lters.

11. Installation is complete. Turn on the power.

VERTICAL VENTING

(If the roof cap has a damper, do not install the

damper blade on the hood.)

Attach the damper with the small sheet metal

screws (#8 x 1/4 ).″

Check the damper

for free operation.

Open the damper

blade to

approximately 80

degrees.

Position the blower for vertical discharge. The

air ow arrow on the blower should point up

towards the vent opening.

When the blower is in position, snap the blower

retainer bar toward the front into the indent.

Reattach the plug into the junction box.

Blower discharge

Air ow arrow

This surface

to rear

3″

5″

Damper blade

to front

This surface to top

Blower

discharge

3″

5″

Air ow arrow

Damper

blade to top

Damper

4. Use the hood as a template. Mark the

locations on the cabinet or wall for ductwork,

electrical wiring and keyhole screw slots.

Cut holes at marked locations for duct and

electrical wiring. For the vertical duct, cut out 3/4″

extra toward the front of the cabinet for movement

of the duct when installing the hood.

5. Run the electrical wires through the wall or

cabinet according to National Electrical Code

and applicable local codes.

NOTE: DO NOT turn the power on until

installation is complete.

6. Drive the screw partway

into the center of the

narrow neck of the keyhole

slots marked on the

cabinets.

7. Follow the directions for vertical or

horizontal venting.

NOTE: If the venting installation is NOT

correct, the blower will run at maximum RPM

regardless of the speed control setting.

When installing the blower housing, be

sure wires cannot contact the blower wheel.

Keyhole slot

in canopy

Screw

(supplied)

Damper

Termékspecifikációk

Márka:	GE
Kategória:	Páraelszívó
Modell:	JV356VAA

Szüksége van segítségre?

Ha segítségre van szüksége GE JV356VAA, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek

Az Ön neve*

Az Ön e-mail címe*

Írja ide kérdését

Útmutatók Páraelszívó GE

GE Profile JV535CCC Útmutató

18 Március 2025

GE UVC9480SLSS Útmutató

31 December 2025

GE JV665HBB Profile Útmutató

17 December 2024

GE UVC9420SLSS Útmutató

8 December 2024

3 Október 2024

30 Szeptember 2024

20 Szeptember 2024

8 Szeptember 2024

GE JVX5365SJSS Útmutató

3 Szeptember 2024

GE Profile JV696SCC Útmutató

2 Szeptember 2024

Útmutatók Páraelszívó

Legújabb útmutatók Páraelszívó

Silverline SOW 900 S Útmutató

30 Március 2025

Atag WM 5 Útmutató

30 Március 2025

Smeg CA60EPX Útmutató

30 Március 2025

CATA C GLAS H BK Útmutató

30 Március 2025

Smeg STH650X Útmutató

30 Március 2025

Elica PIX BL/F/42 Útmutató

30 Március 2025

Electrolux KCC84450CZ Útmutató

30 Március 2025

Etna 4191 inox Útmutató

29 Március 2025

Miele da 249 1 Útmutató

29 Március 2025

Miele DA 420 UL Útmutató

29 Március 2025