Használati útmutató GE GPF375

GE mosogatógép GPF375

Olvassa el alább 📖 a magyar nyelvű használati útmutatót GE GPF375 (8 oldal) a mosogatógép kategóriában. Ezt az útmutatót 4 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/8
18-15/16"
23-5/8"
3/4" Thick Panel
Appearance Side
1-9/16"
3/4"
1/2"
A*
23-5/8"
3/4" Thick Access Panel
Installation
Instructions
3/4" Custom Dishwasher
Door and Access Panel Kit
GPF375 Kit
Note: The custom wood
access panel should
evenly match the bottom
of adjacent cabinets.
Adjustments made to the
leveling legs to obtain
correct height can affect
the vertical dimension
(height) of the access
panel.
1 CUT 3/4" THICK CUSTOM
PANELS TO SIZE
• Cut the 3/4" thick door panel to the dimen-
sions shown.
• Rout the bottom edge of the door panel on
the appearance side, 1/2" deep and 1-9/16"
high resulting in 1/4" thickness. See
illustration.
• The access panel height may be 3-3/4" to
4-1/4" max. The access panel height can vary
depending upon toekick height and adjust-
ments made to the leveling legs.
*3-3/4" min., 4-1/4" max. for typical 4" toekicks.
Adjustments may be required to match adjacent cabinet
fronts.
WARNING:
To prevent electric shock, disconnect electrical
power supply to dishwasher before changing
panels. Do not operate dishwasher while
changing panels or when lower access panel
assembly is removed.
Before you begin
Read these instructions completely
and carefully.
IMPORTANT – Save these instructions
for local inspector’s use.
IMPORTANT – Observe all governing
codes and ordinances.
Note to Installer – Be sure to leave these
instructions with the Consumer.
Note to Consumer – Keep these instructions
with your Owner’s Manual for future
reference.
STOP
TOOLS AND MATERIALS REQUIRED:
• 1/4" socket driver
• Phillips screwdriver
• Electric drill
• 1/8" and 3/16" drill bits
• Carpenters square
• Safety Glasses
The custom panels should be constructed in
the same manner as cabinet doors. Cut edges
can be seen and must be finished for the best
appearance.
The GPF475 Trim Kit provides for the installa-
tion of 3/4" thick custom door and access
panels with a typical 4" high toekick.
KIT INCLUDES:
• Door panel support
• 7, 5/8" phillips flat head screws
• 3 round head screws
• GPF100 spring kit
2 REMOVE LOWER ACCESS
PANEL ASSEMBLY
• Remove the two screws below the access
panel. Retain screws.
• Loosen the two screws located between the
door and the access panel. Do not attempt
to remove these screws. They are secured
to the access panel with washers.
• Remove the access panel assembly and
toekick from the dishwasher. Set aside.
NOTE: Do not remove the insulation behind
the access panel or toekick.
3 MOUNT CUSTOM PANEL TO
METAL SUPPORT PANEL
A
• Place the metal door panel support on the
custom panel, with the projecting tabs
overlapping and against the bottom edge.
Center the support panel by matching the
center line to the diamond cutout.
NOTE: Do not remove tape from adhesive
strips.
• Mount custom panel to metal support panel
• Lay the custom panel on a flat surface with
appearance side down.
• Measure and mark the center line. Use a
carpenters square to draw the center line.
C
• Remove the custom panel from the support.
• Remove tape from adhesive strips on the
metal support – on the side that touches the
custom panel.
• Carefully, position the metal support onto the
custom panel with center line showing
through the diamond. Press the metal sup-
port against the panel.
B
2
Loosen 2 Screws
Escutcheon
Door
Panel
Access Panel
Toekick
Foam
Double Sided
Tape
Tab
Tabs
Overlap
Bottom
Edge
Metal Support
Overlaps
Top
Edge
Remove
Tape Covering
Adhesive Strips
• Drill 1/8" dia. pilot holes, 5/8" deep through
support holes.
• Install 4 flathead screws through the support
and into the panel.
CAUTION:
Do not drill pilot holes too deeply to avoid
damaging the appearance side of the panel.
E
• Remove tape from adhesive strips on the back
side of the metal support.
• Carefully, mount the panel onto the dish-
washer by tipping the protruding metal at the
top under and up against the escutcheon.
D
3 MOUNT CUSTOM PANEL TO
METAL SUPPORT PANEL
CONTINUED
F
• Secure the panel to the door by installing
3 round head screws into the bottom of the
metal support and into the dishwasher door.
Install center screw first, then left and right
screws.
• Press the custom panel against the dish-
washer door.
3
Drill 4 Holes,
In Locations Shown
Custom Panel
Install 3 Round
Head Screws

Termékspecifikációk

Márka: GE
Kategória: mosogatógép
Modell: GPF375

Szüksége van segítségre?

Ha segítségre van szüksége GE GPF375, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók mosogatógép GE

GE

GE PDP755SYRFS Útmutató

31 December 2025
GE

GE PDT755SYRFS Útmutató

31 December 2025
GE

GE Café CXADTH1PMSS Útmutató

8 December 2024
GE

GE GSM2200NBB Útmutató

30 Szeptember 2024
GE

GE CDT888P2VS1 Útmutató

30 Augusztus 2024
GE

GE CDP888M5VS5 Útmutató

30 Augusztus 2024
GE

GE Profile PDT145SGLWW Útmutató

26 Augusztus 2024
GE

GE Profile PDT145SSLSS Útmutató

26 Augusztus 2024
GE

GE Profile PDW7880NSS Útmutató

26 Augusztus 2024
GE

GE CDT765SSFSS Cafe Útmutató

24 Augusztus 2024

Útmutatók mosogatógép

Legújabb útmutatók mosogatógép

Miele

Miele G 4485 Útmutató

10 Április 2025
Miele

Miele G 4940 SC Front Jubilee Útmutató

10 Április 2025
AEG

AEG Favorit R 3Prog Útmutató

9 Április 2025
Miele

Miele G 5432 SCU Útmutató

9 Április 2025
Miele

Miele G 5495 SCVi XXL Active Plus Útmutató

9 Április 2025
Oranier

Oranier GAVI 7592 XL Útmutató

9 Április 2025
Amica

Amica DIM44D6EBq Útmutató

9 Április 2025
Sharp

Sharp QW-I1GI47EX Útmutató

9 Április 2025
Beko

Beko BDFN26450XC Útmutató

8 Április 2025
Asko

Asko DFI544B Útmutató

8 Április 2025