Használati útmutató Garmin GC 14

Garmin nincs kategorizálva GC 14

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Garmin GC 14 (4 oldal) a nincs kategorizálva kategóriában. Ezt az útmutatót 4 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF

Oldal 1/4

GC™ 14

INSTALLATION INSTRUCTIONS

Getting Started

Getting StartedGetting Started

WARNING

See the guide in the product box for product warnings and other Important Safety and Product Information

important information.

Mounting Considerations

Mounting ConsiderationsMounting Considerations

You can mount the camera upside-down or sideways. You can reverse the camera image to use in rearview

mode. See your chartplotter owner's manual for instructions.

You should mount the camera in a location where it is

• not an obstacle in doorways or walkways.

• not exposed to extreme temperatures.

• not exposed to gas or oil.

• not exposed to radioactivity.

• not facing into direct sunlight or a direct reflection of sunlight.

Tools Needed

Tools NeededTools Needed

• 1 A fuse or circuit breaker

• Drill and 2 mm (3/32 in.) drill bit

Mounting the Camera

Mounting the CameraMounting the Camera

1Secure the template to the mounting location.

2Using a 2 mm (3/32 in.) drill bit, drill the pilot holes.

3Adjust the dome base to the correct orientation for your desired camera tilt.

4Secure the dome base to the mounting location using the included tapping screws .

5Insert the camera into the dome base.

6Secure the set screws into the dome front using the included wrench.

GUID-F3AB61D3-A701-4DF6-A841-B96657F5BE46 v3April 2021

Installation Considerations

Installation ConsiderationsInstallation Considerations

You must connect the camera power wire to the battery through a 1 A fuse or circuit breaker. If you do not use

a fuse or circuit breaker, the camera can malfunction.

Some Garmin® GPSMAP® chartplotters have a built-in CVBS video encoder. Video from the camera or cameras

appears on all chartplotters on the network when plugged into a single CVBS IN port. Go to garmin.com/gc14

for a list of compatible GPSMAP chartplotters.

If you want to use more than one camera or the chartplotter does not have a CVBS IN port, you must use an

encoder.

You can add up to four cameras to one encoder and up to two encoders to the Garmin Marine Network.

NOTE: To reduce the possibility of interference, you can install a composite video ground loop isolator (not

included) between the camera and any chartplotters that do not have isolated power grounds.

Installation Diagram

Installation DiagramInstallation Diagram

GC 14

1 A fuse or circuit breaker (not included)1

12 Vdc power source

BNC to BNC coaxial video cable (not included)

Compatible Garmin chartplotter

Composite video ground loop isolator (not included)

1 You must connect the camera power wire to the battery through a 1 A fuse or circuit breaker. If you omit a fuse or circuit breaker, the camera can malfunc

tion.

Installation With Encoder Diagram

Installation With Encoder DiagramInstallation With Encoder Diagram

You can add more than one camera to your network when you use an encoder.

GC 14

1 A fuse or circuit breaker (required, not included)1

12 Vdc power source

BNC to BNC coaxial video cable (not included)

Network cable

Power-over-Ethernet isolation coupler (GPN 010-10580-10)

Garmin Marine Network cable

Axis® Q7424 Encoder (optional/not included)

Compatible Garmin chartplotter

Composite video ground loop isolator (not included)

Troubleshooting

TroubleshootingTroubleshooting

Video Does Not Appear on the Chartplotter Screen

Video Does Not Appear on the Chartplotter ScreenVideo Does Not Appear on the Chartplotter Screen

• Verify all cables are firmly connected.

• Verify the video cable is connected to the camera video output port.

Image on the Chartplotter Screen is Dim or Dark

Image on the Chartplotter Screen is Dim or DarkImage on the Chartplotter Screen is Dim or Dark

• Verify the lens is clean. If necessary, wipe the lens with a soft, clean cloth.

• If the camera is exposed to too much direct light, change the camera position or location.

• Adjust the contrast on your chartplotter. See your chartplotter manual for instructions.

1 You must connect the camera power wire to the battery through a 1 A fuse or circuit breaker. If you omit a fuse or circuit breaker, the camera can malfunc

tion.