Használati útmutató Futaba SBD-1

Futaba Rádióvezérlésű játékok SBD-1

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Futaba SBD-1 (2 oldal) a Rádióvezérlésű játékok kategóriában. Ezt az útmutatót 12 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/2
󾙏CAUTION
󾙍 Do not connect any device (gyro, battery,
etc.) other than servos to the servo
connector of the SBD-1. There is the danger of
erroneous operation or damage.
󾙍 Do not connect an S.BUS conne cto r
of the SBD- 1 to other than an S.BUS
servo connection port. There is the danger of
erroneous operation or damage.
󾙏WARNNG
󾙋 Always use in the state in which the
SBD-1 is firmly attached to the fuselage
of the airplane or helicopter. There is the danger
of loss of control and crashing if the connector is
disconncted by vibration and shock.
Futaba Co rp. will not be resp onsible for
damage caused by combination with other
than Futaba Genuine parts.
S.BUS Decoder
INSTRUCTION MANUAL
Before using your new SBD-1, please read this manual
thoroughly and use the system properly and safely.
After reading this manual, store it in a safe place.
•Channel setting by SBC-1
1 Connect the S.BUS connector of the SBD-1
to the S.BUS servo connection port of the
SBC-1.
2 C o nne c t t he bat t e r y t o t he bat t e r y
connection port of the SBC-1.
* Status display LED blinks slowly. (About 1 sec/time)
3 Quickly press and release the SBC-1 setting
switch and select the servo connection port
at which the channel is to be set.
* Each time the switch is pressed, the set servo
connection port and the number of times the LED
blinks change.
SBC-1 SBD-1 servo con-
nector selection
Se tt in g s wit ch
operation LED display
W h e n p o w e r
turned on
1 sh o r t b l i n k
each second
Connector (SX1)
selected.
Switch pressed
a nd r e l e a s e d
quickly
2 s h o r t b li nk s
each second
Connector (SX2)
selected.
Switch pressed
a nd r e l e a s e d
quickly
3 s h o r t b li nk s
each second
Connector (SX3)
selected.
* (Channel conrmation)
When the operation position of the channel selector
switch and the channel set at the connector during
the servo connector selection coincide, the SBD-1
LED changes to a steady light.
4 Set the SBC-1 channel selector switch to
the channel you want to set.
5 Hold down the setting switch (about 1
second).
©Copyright 2010. No part of this manual may be reproduced in any form without prior permission. The contents of this
manual are subject to change without prior notice. While this manual has been carefully written, there may be inadvertent
errors or omissions. Please contact our service center if you feel that any corrections or clarifications should be made.
FUTABA CORPORATION Phone: +81 475 32 6982, Facsimile: +81 475 32 6983
1080 Yabutsuka, Chosei-mura, Chosei-gun, Chiba 299-4395, Japan
1M23N23401 ©FUTABA CORPORATION 2010, 2 (1)
Meaning of Special Markings
Pay special attention to safety where indicated by the following marks:
󾙏DANGER Procedures which may lead to dangerous conditions and
cause death/serious injury if not carried out properly.
󾙏WARNING
Procedures which may lead to a dangerous condition or
cause death or serious injury to the user if not carried out
properly, or procedures where the probability of superficial
injury or physical damage is high.
󾙏CAUTION
Procedures where the possibility of serious injury to the user
is small, but there is a danger of injury, or physical damage,
if not carried out properly.
󾙍= Prohibited 󾙋= Mandatory
Usage Precautions
Name of Each Part and Accessories
Channel Setting
Usage Method
•Connection
1 Connect the S.BUS connector of the SBD-1
to the receiver S.BUS connection port or
S.BUS hub.
2 Connect a conventional servo or an S.BUS
servo to the servo connector of the SBD-1.
* When an servo was connected, that servo S.BUS
will operate as a conventional servo. However,
it operates on th e channel s et at th e s er vo
connector of the instead of the channel set SBD-1
at the servo itself.
Thank you for purchasing an SB D-1, S.BUS* 1
decoder. The SBD-1 is a converter for using
conventional servos (other than S.BUS servo*2) with
the S.BUS system.
There are ve types of SBD-1 available as follows.
Type Total Length
S.BUS Decoder
SBD-1
200 200mm (8in.)
400 400mm (16in.)
600 600mm (24in.)
1100 1,100mm (43in.)
1600 1,600mm (63in.)
Before installing the SBD-1 to the fuselage, set
each channel at each servo connector ( SX1~3).
Use the SBC-1 S.BUS channel changer or CIU-2
USB adapter (PC-Link software for setting) to set
the channel.
* S.BUS decoder channel setting is impossible with
the receiver .S.BUS R6108SB
* PC-Link software can be downloaded from the
home page of your region's Futaba importer.
Conventional servo
(or S.BUS servo)
to the receiver S.BUS con-
nection port or S.BUS hub
SX1
SX2
SX3
SBD-1
Servo connector
(Upper)
SX1
(Middle)
SX2
(Lower)
SX3
S.BUS connector
[SBD-1 Ratings]
•Dimensions:
41.8x12.3x8.4mm
(1.65x0.48x0.33in.)
(excluding protruding)
•Weight:
6.9/10.8/14.7/24.5/34.3g
(0.24/0.38/0.52/0.86/1.21oz.)
•Powerrequirement:
Ni-Cd, Ni-MH 4 to 5 ce lls
equivalentbattery(Futaba)
•Op e r a t i n g t e m p e r a t u re
range:-10to+45°
*During channel setting,the LED blinks quickly
(about 5 times/sec). When the LED changes to a
steady light, channel setting is complete.
6 To s e t th e c h an ne l o f ot h e r se r vo
conne ction por ts, quickly p ress an d
release the setting switch and repeat steps
4 and 5.
<Accessories>
Channel No. Label
•PutthechannelNo. labelon theservoconnector
fortheidenticationofchannelNo..
Instruction manual (this manual)
*1 S.BUS: Serial communication system for Futaba R/C system
*2 Use the S.BUS hub as the extension code used for the S.BUS servo. Also SBD-1 can be used.

Termékspecifikációk

Márka: Futaba
Kategória: Rádióvezérlésű játékok
Modell: SBD-1

Szüksége van segítségre?

Ha segítségre van szüksége Futaba SBD-1, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók Rádióvezérlésű játékok Futaba

Futaba

Futaba SBS-01RO Útmutató

15 Január 2025
Futaba

Futaba 12Z Útmutató

4 Október 2024
Futaba

Futaba 2PL Útmutató

27 Szeptember 2024
Futaba

Futaba SKYSPORT_4YBF Útmutató

17 Szeptember 2024
Futaba

Futaba 8J Útmutató

14 Szeptember 2024
Futaba

Futaba 6EX-2 Útmutató

14 Szeptember 2024
Futaba

Futaba FC28 Útmutató

14 Szeptember 2024
Futaba

Futaba 6EXA Útmutató

9 Augusztus 2024
Futaba

Futaba FP2F Útmutató

6 Augusztus 2024
Futaba

Futaba FP7UAFS Útmutató

6 Augusztus 2024

Útmutatók Rádióvezérlésű játékok

Legújabb útmutatók Rádióvezérlésű játékok

Carson

Carson Easy Tyrann 550 Útmutató

1 Április 2025
E-flite

E-flite Night Radian 2.0m BNF Basic Útmutató

30 Március 2025
E-flite

E-flite UMX Timber X BNF Basic Útmutató

30 Március 2025
E-flite

E-flite UMX Twin Otter Útmutató

30 Március 2025
Hobbywing

Hobbywing Platinum 150A V5.1 Útmutató

30 Március 2025
E-flite

E-flite Night Radian 2.0m PNP Útmutató

30 Március 2025
Hobbywing

Hobbywing EZRUN 4278SD G2 Útmutató

30 Március 2025
PowerBox Systems

PowerBox Systems PBR-12X Útmutató

30 Március 2025
Amewi

Amewi 22487 Útmutató

30 Március 2025
Amewi

Amewi 22452 Útmutató

30 Március 2025