Használati útmutató Futaba FP2GS
Futaba
Rádió vezérlés
FP2GS
Olvassa el alább 📖 a magyar nyelvű használati útmutatót Futaba FP2GS (4 oldal) a Rádió vezérlés kategóriában. Ezt az útmutatót 4 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra
Oldal 1/4
Futaba
DIGITAL PROPORTIONAL
RADIO CONTROLFP-2GS
D60431
SPECIAL FEATURES:
SET CONTENTS AND RATINGS
(Specifications are subject to change without prior notice.)
TRANSMITTER FP-T2GS
• Contemporary
styling with smooth operating gimbals for
superior control.
• 500mW output.
• Battery level
meter indicates the state of the battery
voltage at a glance.
• Built-in antenna.
RECEIVER FP-R102GF
•BEC (Battery Eliminator Circuitry) system allows sharing
of the running Nicd battery and eliminates the need
for a
regulator and diode.
•High performance 2 channel receiver with ASP system
when used with the proper transmitter.
•Crystal
socket
uses
a
new
type
of highly reliable subminia-
ture pins. Reliability is increased and the crystal can be
changed from the outside.
SERVO FP-S128
SMALL, RUGGED. HIGH NEUTRAL SERVO
•Skew type armature motor.
Movement of the trimmer by even one notch is tracked by
a skew type motor which displays a performance near that
of a
coreless motor.
•New indirect drive potentiometer improves vibration and
shock resistance and neutral accuracy.
•Futaba low-power custom 1C provides extremely high
torque, narrow dead band, and superior tracking.
•Fiberglass reinforced PBT (polybutylene terephthalate)
injection
molded
servo
case
is
mechanically strong and
invulnerable to glow fuel.
•Strong
polyacetal
resin
ultra-precision
servo
gear
features
smooth operation, positive neutral, and very little backlash.
•Fiberglass reinforced epoxy resin PC board with thru-the-
hole plating improves servo amp vibration and shock resist-
ance.
•Three pin connector eliminates faulty contact and improves
reliability against vibration and shock. Housing has a
reverse insertion prevention mechanism.
•Special grommet simplifies
mounting of the servo and has
an excellent cushioning effect.
•Six special adjustable splined horns.
•High 48.7 oz.in
(3.5kg-cm) maximum output torque allows
use
in almost any model.
Model number
Transmitter
Receiver
Servo
Switch, battery holder, etc.
FP-2GS
FP-T2GSx1
FP-R102GFx1
FP.S128.x2
TRANSMITTER FP-T2GS.
Operating method 2 stick system
Transmitting frequency 27MHz band, 72MHz band
Modulation system AM (amplitude modulation)
Power requirement
12V,
round penlight battery x 8
Receiver FP-R102GF
Receiving frequency
27MHz band, bands 1 to 6
72,75MHz
455kHz
3kHz/-3dB
550 yards (500m) on the ground
when used with FP-T2GS (At the
best radio wave condition of envi-
ronment)
4.8V
to
8.4V
7.2V/13mA,4.8V/33mA
1.46x
2.19
x
0.75
in
(37
x
55.5
x
19mm)
1.34
oz
(38g)
Intermediate frequency
Selectivity
Receiving range
Power supply
Current drain
Dimensions
Weight
SERVO FP-S128
Control system
Operating angle
Power requirement
Current drain (IDLE)
Output torque
Operating speed
Dimensions
+pulse width control
One side 45° or more
4.8V-6V
6.0V, 8mA (at idle)
48.7 oz.in. (3.5 kg-cm)
0.24 sec/60°
1.6x0.8x 1.6 in.
(40.5 x 20 x 40.5mm)
1.92oz. (53g)
Weight
HANDLING THE TRANSMITTER
•The name of each part of the transmitter is given in the figure.
Familiarize yourself with their operation.
•Remove the battery cover on the rear of the transmitter as
illustrated in the figure, and insert 8 round penlight batteries,
paying careful attention to their polarity.
•Extend the antenna fully, and set the power switch to the
ON position. The pointer of the level meter should deflect to
the green zone. If it fails to deflect, or deflects slowly, the
polarity of the batteries is incorrect, or the batteries are
faulty.
•Since the range of the radio waves will become short when
the pointer of the level meter deflects to the red zone, re-
place the batteries when the pointer only deflects to the
boundary between the green and red zones.
•The
trim
lever
is
used
to fine
adjust
each
channel.
Use
it for
neutral adjustment and to correct the flying posture after
the mechanism has been installed. After test flight, operate
with the trim lever in the neutral position, as far as possible,
by correcting with the rod adjuster, etc.
•Since the elevator stick employs a self-neutral system, install
the sliding plate as shown in the figure when changing it to a
ratchet system. Then remove the strong spring attached to
the hook and replace it with the spring supplied as an ac-
cessory.
•When the transmitter is used with a tank, the direction of the
stick can be changed 90 degrees by removing the four rudder
stick mounting screws.
•To change the crystals, loosen the rear cover mounting screws,
remove the rear cover, and then replace the crystal. The
crystal is located at the left side of the printed wiring board.
The transmitter crystal is marked (T) and the receiver crystal
is marked (R). CAUTION: Frequency change has to be done
under the supervision of FCC licensed personnel.
(Engine control
trim)
Elevator trim
Elevator stick
(engine control
stick)
The batteries can be
easily loaded by
inserting them
four at
a time from the back.
Modification from self-neutral
system to ratchet system.
Install sliding plate
Replace with
weak spring
Fig.
3
Slide in the direction
of the arrow while
pushing here.
Rear cover mounting screws
Fig.
2
Fig.1
Rudder stick
Rudder
trim
Antenna
Level meter
Power switch
RECEIVER FP-R102GF AND SERVO FP-S128
The BEC mark is displayed on the front of the receiver of BEC (Battery
Eliminator Circuitry) system sets with a receiver with shared power supply
regulator.
Your NEW FUTABA Digital Proportional R/C system is guaran-
teed against defects in workmanship and material for 180 days
from the date of purchase when the attached registration card is
returned to us within ten days of purchase.
This Guarantee is null and void if the R/C system has been im-
properly handled, damaged in a crash, or tampered with and
does not cover the replacement of plastic housings or electronic
components damaged due to the use of improper voltages.
When service is required, please take your equipment to your
local authorized service station or ship it directly to us. All
postage, shipping, and insurance charges must be paid by the
user.
(3) When motor car uses an ordi-
nary common power supply
chassis
Red common 2P
connector
(Female pins)
Buy the red common 2P
connector from the kit
manufacturer and connect to
the controller.
Pin 1: Minus
Pin 2: Plus
The Futaba BEC (Battery Eliminator Circuitry) system and BEC
& ASP (Adjustable Safety Position) system can also use a com-
mon power supply with the conventional four penlight batteries
system (separate power supply).
Connect the servo and switch as
shown in the figure and extend
the transmitter and receiver ante-
nna fully.
Red common 2P
connector (male pins)
Antenna mire
Receiver FP-R102GF
Switch
ON
OFF
Steering servo
Throttle servo
Connection to this connector
(1)When chassis power supply of
engine or motor car is separate
Wrapped with
rubber band.
Red common 2P
connector
(Female pins)
Receiver crystal
Fig.
4
Connect to the red common
2P connector of the control-
ler.
Controller
Red common 2P
connector
(Female pins)
(2) When motor car uses a speci-
al 8EC system chassis (com-
mon power supply specifi-
cations)
(75MHz-OPTIONAL)
•A common power supply regulator and diode may also be supplied with the speed controller, depending on the vehicle
kit. Since they cause a voltage drop, always remove them.
TO BUYERS OF THE FP-2GS (FP-R102GF)
When using a Futaba motor control amp instead of
the speed controller supplied with the vehicle, turn
off the ASP (Adjustable Safety Position) system as
shown in the figure.
R102GF ASP
release
connector
Insert the ASP release co-
nnector packed "with
the
set at this 2P connector
(male pins) on the
printed
wiring board.
Fig. 5
•Set the transmitter power switch to ON, then set the receiver
power switch to ON. The servos stop near the neutral position.
Operate the transmitter sticks and check if each servo faithfully
follows operation of the sticks.
•Connect the pushrod to each servo horn, then check if the direc-
tion of travel of each servo matches the transmitter operation.
•Operate each servo over its full travel and check if the pushrod
binds or is too loose. Applying unreasonable force to the servo
horn will adversely affect the servo and quickly drain the battery.
Be especially careful when using 8.4V.
•Always make the full stroke (including trim) of the servo horns
somewhat larger than the full travel. Adjust the servo horns so
that they move smoothly even when the trim lever and stick are
operated simultaneously in the same direction.
• Be alert for noise.
Always solder a noise killing capacitor to the running motor. If
metal parts touch each other due to vibration, noise will be gener-
ated and cause the receiver servos to operate erroneously. We re-
commend the use of noiseless parts.
• Even though the receiver antenna wire is long, do not cut
or
bundle it. The range of the radiowaves will be shortened.
• A spare horn is provided. Use it as required.
•Wrap the receiver in sponge rubber and wrap rubber bands around
the sponge rubber. Mount the receiver so it is not exposed to vi-
bration, does not touch the frame, and does not move.
•When the receiver is installed on a board or used where it may be
splashed with mud and water, place it in a plastic bag, etc. and
wrap a rubber band around the open end of the bag to waterproof
and dustproof the receiver. After use, remove the receiver from
the bag to prevent condensation.
• Use the rubber bands wrapped around the receiver to hold the
servo and switch leads.
•After mounting is complete, recheck each part, then check the
transmitting range by making the transmitter antenna as short as
possible and extending the receiver antenna fully and operating
the set from a distance of 20m to 30m. The movement of each
servo should follow the movement of the transmitter sticks.
•The crystal can be changed from the outside of the receiver case.
Always use a Futaba transmitter and receiver crystal pair as the
replacement crystals.
Fig.
6
Fig.
7
• Install the servos firmly. Install the servo to the servo tray
as shown in the figure. In other cases, install the servo as
described in the model manufacturer's manual.
REPAIR SERVICE
• When requesting repair of trouble that has occurred suddenly
of from long use, describe the trouble symptoms in as much
detail as possible.
This will facilitate detection of the trouble point and shorten
the repair period greatly.
•
Defects caused
by
faulty
materials
or
workmanship
will
be
corrected free of charge.
• This limited warranty is null and void if the set has been tam-
pered with or disassembled.
Refer to warranty statement for details.
WORLD SALES & SERVICE FACILITIES
Australia: FUTABA SALES AUSTRALIA PTY. LTD., Lebanon:
MELBOURNE TEL: 211-4788
Argentine: MODELISMO AE RONAUTICO DEGA SRL. New Zealand:
BUENOS AIRES TEL: 393-2299
Canada: UDISCO LTD., MONTREAL
TEL: 481-8109 Norway:
Chile: HOBBY LANDIA, SANTIAGO
TEL: 743957 Singapore:
Denmark: FUTABA IMPORT DENMARK,
COPENHAGEN TEL: 02-91-0101 South Africa:
England: RIPMAX LIMITED, LONDON
TEL: 01-8048272 Spain:
Finland: NORETRON KY. HELSINKI
TEL: 90-488880 Sweden:
Greece: C. & G. MACR1YIANNIS CO., PIRAEUS
TEL: 021-3604391 • or 021-41 76191 U.S.A.:
Hong Kong: RADAR CO. LTD. TEL: 3-680507
Italy: RADIOSISTEMI SRL, Carrara W.Germany:
TLX: 500494 FORTIMI
FAX: 0039-585-52247
KHAIRALLAH MODELCRAFT, BEIRUT
TEL: 326-681
AMALGAMATED WIRELESS
(AUSTRALIA) N.Z. LTD. WELLINGTON
TEL: 58-979
HARALD LYCHE CO. A/S, Drammen
TEL: (03) 8339 70
SINGAPORE HOBBY SUPPLIES
TEL: 533-0337
REDIPAK (PTY.) LTD.,
JOHANNESBURG TEL: 21-1511
HOBBY & TOY INTERNATIONAL,
VALENCIA TEL: (96) 357 23 93
RADIO CONTROL CENTER,
JONKOPING TEL: 036-145360
FUTABA CORPORATION OF AMERICA,
CALIFORNIA TEL: 213-537-9610
ROBBE MODELLSPORT GMBH,
GREBENHAIIM TEL; 06644-870
Termékspecifikációk
| Márka: | Futaba |
| Kategória: | Rádió vezérlés |
| Modell: | FP2GS |
Szüksége van segítségre?
Ha segítségre van szüksége Futaba FP2GS, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek
Útmutatók Rádió vezérlés Futaba
23 Augusztus 2024
23 Augusztus 2024
23 Augusztus 2024
23 Augusztus 2024
23 Augusztus 2024
23 Augusztus 2024
23 Augusztus 2024
23 Augusztus 2024
23 Augusztus 2024
23 Augusztus 2024
Útmutatók Rádió vezérlés
- Rádió vezérlés Reely
- Rádió vezérlés Hitec
- Rádió vezérlés Saturn
- Rádió vezérlés Absima
- Rádió vezérlés Graupner
- Rádió vezérlés Multiplex
- Rádió vezérlés Robbe Futaba
- Rádió vezérlés Robbe
- Rádió vezérlés JRpropo
- Rádió vezérlés Sanwa
- Rádió vezérlés Rush
Legújabb útmutatók Rádió vezérlés
16 Október 2024
14 Október 2024
24 Augusztus 2024
22 Augusztus 2024
22 Augusztus 2024
21 Augusztus 2024
20 Augusztus 2024
19 Augusztus 2024
19 Augusztus 2024
19 Augusztus 2024