Használati útmutató Focal FDP 4.600

Focal Vevő FDP 4.600

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Focal FDP 4.600 (8 oldal) a Vevő kategóriában. Ezt az útmutatót 4 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/8
1
POWER PER CHANNEL:
• 4 x 150 wRMS @ 4ohms
• 4 x 200 wRMS @ 2ohms
• 2 x 400 wRMS (Bridged @ 4ohms)
ROUTE SWITCH
• 1+2 = All four RCA inputs are used.
• 3+4 = Input signal on channels 3+4 are routed to channels 1+2. Use this mode when you need a band pass filter
on all four channels.
Recommended when bridging channels 1, 2, 3, 4.
The level controls still function.
• Copy = Input signal and filters on channels 3+4 are copied to channels 1+2. Use this mode when you need a band
pass filter on all four channels.
Recommended when bridging channels 1,2,3,4.
The level controls still function.
CHANNELS 1 & 2 CROSSOVER CONFIGURATION
• Flat: Full Range Signal. No crossover filter used.
• HP: Activates the High Pass Filter for a midbass or tweeter.
CHANNELS 3 & 4 CROSSOVER CONFIGURATION
• Flat: Full Range Signal. No crossover filter used.
• HP: Activates the High Pass filter.
• LP/BP: Activates the selection of either a Low Pass filter for woofer or a Band Pass filter for midrange.
• MONO Mode: Inputs 3+4 are mixed to mono for bridge mode operation. If 1+2 ROUTE is set to COPY then 1+2
will also be mono subwoofer and the remote volume control will control level.
The subwoofer remote volume control is activated. There is a clip distortion light on the remote volume control.
If you see this light on, reduce volume until the light goes out so that you do not damage your speaker.
AUTOMATIC POWER TURN ON/OFF
1. The best way to automatically turn the amplifier power on and off is to use the REM wire from your source radio
connected to the REM amplifier terminal.Band Pass for a subwoofer or midbass of a 3 way speaker.
2. If your original equipment stereo or source radio has a BTL amplifier then the RCA inputs have an auto turn
on sensing circuit. When you connect the high level BTL speaker wires to the RCA input the REM wire is not
necessary.
FDP 4.600 : FOUR CHANNEL AMPLIFIER
Operation / Configuration
2
RCA INPUT, BOTH LOW LEVEL AND HIGH LEVEL.
• The amplifier control has sufficient adjustment range for both low level and high level input into the RCA LEVEL
jacks. A factory source radio that does not have RCA output, using the wires that are connected to the speakers,
can be directly connected to the RCA jacks when the amplifier control is adjusted to 8V.LEVEL
SETTING LEVEL
• Set the amplifier control to minimum before you turn on the amplifier for the first time.LEVEL
• For lowest distortion and lowest noise the amplifier should be set at the lowest setting that yields LEVEL
sufficient loudness without distortion. For lowest noise your source radio volume control should be near
maximum that does not cause distortion.
• To find the best amplifier setting: LEVEL
With the amplifier at minimum, slowly increase the source radio volume to around 3/4 without distortion. LEVEL
Then, slowly turn up the amplifier control to the maximum desired loudness. Listen very carefully and LEVEL
turn down the amplifier control if you hear any distortion.LEVEL
FPD 600.4 CONFIGURATION EXAMPLES
4 CHANNEL STEREO NON-BRIDGED
• (SEE GRAPHIC B1)
• If you have four input wires from the source deck, plug them into inputs 1+2 and 3+4.
Set ROUTE switch to 1+2.
• If you have two input wires from the source deck, plug them into inputs 3+4.
Set ROUTE switch to 3+4.
Set the switch to STEREO.
• If you are NOT using a subwoofer set all switches to flat. If you hear distortion in your woofers set all switch to
HP and adjust all HP frequency until the distortion goes away, this will probably be around 50 Hz to 70 Hz.
RADIO FLAT or HP50Hz
1+250Hz FLAT or HP
STEREO
B1
XOVER
XOVER XOVER
XOVER
B1 <GRAPHIC of Source Radio to input channel 1+2, 3+4 of amplifier. Woofer/Tweeter/Xover on channels 1+2, 3+4>
3
IF YOU ARE USING TWO SUBWOOFERS:
• (SEE GRAPHIC B2)
• Put your woofer/tweeters on channel 1+2.
Set 1+2 switch to HP.
Adjust 1+2 HP frequency to 50 Hz.
• Subwoofers on channel 3+4.
Set 3+4 switch to LP/BP.
Set 3+4 switch to LP.
Adjust 3+4 LP frequency to 50 Hz.
Set the switch to MONO.
Plug in the remote sub control.
RADIO LP LP/BP50Hz
3+450Hz HP
MONO
B2
+ –
SUBWOOFER
+ –
SUBWOOFER
REMOTE SUB CONTROL
XOVER
XOVER
B2 <GRAPHIC of Source Radio to input channel 3+4 of amplifier. Woofer/Tweeter/Xover on channels 1+2, one

Termékspecifikációk

Márka: Focal
Kategória: Vevő
Modell: FDP 4.600

Szüksége van segítségre?

Ha segítségre van szüksége Focal FDP 4.600, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók Vevő Focal

Focal

Focal FDP 1.900V2 Útmutató

26 Augusztus 2024
Focal

Focal R-4280 Útmutató

19 Augusztus 2024
Focal

Focal Impulse 4.320 Útmutató

19 Augusztus 2024
Focal

Focal FPX 4.400 SQ Útmutató

19 Augusztus 2024
Focal

Focal FPX 1.100 Útmutató

19 Augusztus 2024
Focal

Focal FPS 4160 Útmutató

18 Augusztus 2024
Focal

Focal FDP 1.900 Útmutató

18 Augusztus 2024
Focal

Focal FDP 6.900 Útmutató

18 Augusztus 2024
Focal

Focal FDP 6.900 V2 Útmutató

17 Augusztus 2024
Focal

Focal FDS 2.350 Útmutató

17 Augusztus 2024

Útmutatók Vevő

Legújabb útmutatók Vevő

DJI

DJI D-RTK 3 Útmutató

5 Április 2025
Phonocar

Phonocar PH544 Útmutató

5 Április 2025
QSC

QSC SPA-Qf 60x2 Útmutató

2 Április 2025
Harper

Harper HDT2-5010 Útmutató

2 Április 2025
Harper

Harper HDT2-2010 Útmutató

2 Április 2025
Alpine

Alpine MRX-F65 Útmutató

31 Március 2025
Streacom

Streacom TL1 Útmutató

31 Március 2025
Pro-Ject

Pro-Ject Stereo Box DS Útmutató

30 Március 2025
Graupner

Graupner GR-8 Útmutató

30 Március 2025
MB Quart

MB Quart FA2-2000.1 Útmutató

29 Március 2025