Használati útmutató Festo EAPM-L2-SH

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Festo EAPM-L2-SH (1 oldal) a nincs kategorizálva kategóriában. Ezt az útmutatót 3 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Oldal 1/1
Translation of the original instructions
© 2021 all rights reserved to Festo SE & Co. KG
1 Applicable documents
All available documents for the product www.festo.com/sp.è
Document Product
Actuator … 3 5
Proximity switch
User documents
Switch lug
Tab. 1
2 Safety
2.1 Safety instructions
Only mount the product on components that are in a condition to be safely
operated.
Observe tightening torques. Unless otherwise specified, the tolerance is
±20%.
2.2 Intended use
2.2.1 Use
Mounting of a proximity switch for sensing the slide position on the basic profile
of an actuator 3 5
2.3 Training of qualified personnel
Work on the product may only be carried out by qualified personnel who can eval
uate the work and detect dangers. Personnel must have the relevant mechanical
training.
3 Additional information
Accessories www.festo.com/catalogue.è
Spare parts www.festo.com/spareparts.è
4 Product Range Overview
4.1 Scope of delivery
1Sensor bracket (1x)
2Threaded pin (2x)
Fig. 1
4.2 Not in scope of delivery
Mini slide unit EGSS (1x)/spindle axis unit ELGS (1x)/electric cylinder unit EPCS
(1x) or the following actuators:
3Mini slide EGSC (1x)
4Guide axis ELFC/spindle axis
ELGC (1x)
5Electric cylinder EPCC (1x)
Fig. 2
5 Assembly
5.1 Attachment to mini slide
The sensor bracket can also be mounted on the opposite side. However, in this1
case a switch lug cannot be mounted.
Fig. 3
Position sensor bracket in the slot[A] as shown. 1
Tighten threaded pins . Tightening torque: 0.7Nm2
èSensor bracket is jammed in the slot[A].1
5.2 Attachment to guide/spindle axis
The sensor bracket can also be mounted on the opposite side. A switch lug can1
be mounted on both sides.
Fig. 4
Position sensor bracket in the slot[A] as shown. 1
Tighten threaded pins . Tightening torque: 0.7Nm2
èSensor bracket is jammed in the slot[A].1
5.3 Attachment on electric cylinder
The sensor bracket can be mounted on three sides. A switch lug cannot be1
mounted.
Fig. 5
Position the sensor bracket in the slot[A] so the sensor will later be in the1
middle of the profile.
Tighten threaded pins . Tightening torque: 0.7Nm2
èSensor bracket is jammed in the slot[A].1
8135693
EAPM-L2-SH
Sensor bracket
8135693
202101a
[8135695]
Assembly instructions
Festo SE & Co. KG
Ruiter Straße 82
73734 Esslingen
Germany
+49 711 3470
www.festo.com

Termékspecifikációk

Márka: Festo
Kategória: nincs kategorizálva
Modell: EAPM-L2-SH

Szüksége van segítségre?

Ha segítségre van szüksége Festo EAPM-L2-SH, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek




Útmutatók nincs kategorizálva Festo

Útmutatók nincs kategorizálva

Legújabb útmutatók nincs kategorizálva