Használati útmutató Fellowes Fortishred 4250S

Fellowes Papír aprító Fortishred 4250S

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Fellowes Fortishred 4250S (8 oldal) a Papír aprító kategóriában. Ezt az útmutatót 2 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF

Oldal 1/8

Quality Office Products Since 1917

FORTISHREDTM

4250C/4250S

Please read these instructions before use.

Do not discard: keep for future reference.

Veuillez lire ces instructions avant d’utiliser l’appareil.

Ne pas jeter : conserver aﬁn de consulter les directives

ultérieurement, en cas de besoin.

Lea estas instrucciones antes del uso.

No las deseche: consérvelas como referencia futura.

ENGLISH

Models 4250C/4250S

Will shred: Paper, credit cards, CD/DVDs, staples, paper clips and junk mail

Will not shred: Adhesive labels, transparencies, newspaper, cardboard, laminates, file

folders, X-rays or plastic other than noted above

Paper shred size:

Strip-Cut ........................................................................................... 5/32 in. (4mm)

Cross-Cut ........................................................ 5/32 in. x 1-9/16 in. (4mm x 40mm)

Maximum:

Paper entry width .......................................................................... 12-1/5”(310mm)

8.5”x11”, 20lb., (75g) paper at 120V, 60 Hz, 8Amps; heavier paper, humidity or other than

rated voltage may reduce capacity.

* In order to perform at capacity, shredder must be plugged into a dedicated 15Amp,

120V outlet.

CAPABILITIES

KEY

• Operation, maintenance, and service requirements are covered in the instruction

manual. Read the entire instruction manual before operating shredders.

• Keep away from children and pets. Keep hands away from paper entry. Always set

to off or unplug when not in use.

• Keep foreign objects – gloves, jewelry, clothing, hair, etc. – away from shredder

openings. If object enters top opening, switch to Reverse (R) to back out object.

• Never use aerosol products, petroleum based lubricants or other flammable

products on or near shredder. Do not use canned air on shredder.

• Do not use if damaged or defective. Do not disassemble shredder. Do not place

near or over heat source or water.

• Do not operate the machine without the safety shield closed (A)

• This shredder has a Disconnect Power Switch in the cabinet door. The door must

be fully closed to operate shredder. In case of emergency, open cabinet door. This

action will stop shredding immediately.

• Avoid touching exposed cutting blades under shredder head.

• Do not put foreign objects in paper entry.

• Shredder must be plugged into a properly grounded wall outlet or socket of the

voltage and amperage designated on the label. The grounded outlet or socket

must be installed near the equipment and easily accessible. Energy converters,

transformers, or extension cords should not be used with

this product.

• FIRE HAZARD – Do NOT shred greeting cards with sound chips or batteries.

• For indoor use only.

• Unplug shredder before cleaning or servicing.

IMPORTANT SAFETY INSTRUCTIONS — Read Before Using!

BASIC SHREDDING OPERATIONBASIC SET UP

Ensure access to a

dedicated 15Amp,

120V outlet

Open the door

Place cutter head into

top of cabinet, use 2

people

Plug in and make

sure door is closed

Press ( ) ON to

activate

When finished

shredding set to

( ) OFF

Feed paper straight

into paper entry and

release

Do nothing and shredder

will automatically shut

off after 30 minutes of

inactivity

Make sure safety flap

is securely in place

SHREDDER SET-UP TO SHRED

4 51

H. Control Panel and LEDs

1. ON/OFF (blue)

2. Reverse (red)

3. Bin full (yellow)

4. Door open (red)

5. Safety Shield Open (red)

A. Safety Shield

B. Paper entry

C. Disconnect switch (open door)

D. Door

E. Basket (inside)

F. Casters

G. See safety instructions

PRODUCT MAINTENANCE

All shredders require oil for peak performance. If not oiled, a machine may experience

diminished sheet capacity, intrusive noise when shredding and could ultimately stop

running. To avoid these problems, we recommend you oil your shredder each time you

empty your waste bin.

OILING SHREDDER

*Apply oil

across entry

Set to Reverse (R) 2-3

seconds

Set to Off (O)

CLEANING AUTO-START INFRARED SENSORS

FOLLOW OILING PROCEDURE BELOW AND REPEAT TWICE

Paper detection sensors are designed for maintenance free operation. However,

on rare occasions the sensors may become blocked by paper dust causing the

motor to run even if there is no paper present (Note: two paper detection sensors are

located in the center of the paper entry).

Turn off and unplug

shredder

Locate Auto-start

infared sensor

Clean any contamination

from the paper sensors

Use thin, long-handled brush

to clean sensors. Make sure

brush is clean and dry

TO CLEAN THE SENSORS

SHEET CAPACITY SENSOR

Eliminates frustrating jams by preventing overloads.

Electronically measures paper thickness to prevent

paper jams:

Up to RED: Too many sheets have been

inserted. Automatic reverse of paper.

Up to YELLOW: Maximum sheet capacity.

Up to GREEN: Normal sheet capacity

during shredding process.

*Only use a non-aerosol vegetable oil in long nozzle

container such as Fellowes 35250

12 3

ADVANCED PRODUCT FEATURES

SilentShred™ Technology

SilentShred™ noise quality

shreds without noisy disruptions

Sheet Capacity Sensor

Helps prevent paper jams

by indicating sheet capacity

levels during the shredding

process

Safety Shield

Electronically controlled

shield stops shredder

when opened for

advanced safety

Auto Shut Off

After 30 minutes of

inactivity, shredder

automatically turns off for

zero energy consumption

TROUBLESHOOTING

When flashing blue,

too much paper is

inserted. Shredder

will automatically stop

and reverse paper

Gently pull uncut paper

from paper entry

Shred 1 sheet of

paper to clear

cutters. Resume

normal shredding

PAPER JAM

If necessary, press

Reverse (R) to run

shredder in reverse and

then pull uncut paper

from shredder

Overheat Indicator: When flashing alternatively with On/Off

( )

LED, shredder requires a 10-15, minute cool down period. When

( )

is blue, resume shredding

Safety Shield Indicator: When flashing alternatively with On/Off

( )

LED, safety shield is open and shredding will stop. To resume shredding, make sure safety shield is closed.

Door Open Indicator: When flashing alternatively with On/Off

( )

LED, safety shield is open. To resume shredding, make sure the door is closed.

Paper Capacity Indicator: When flashing blue, too much paper is inserted. Shredder will automatically stop and reverse paper. See Paper Jam section below.