Használati útmutató Extech AUT20

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Extech AUT20 (1 oldal) a Mérőberendezések kategóriában. Ezt az útmutatót 4 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Oldal 1/1
USER MANUAL
AUT20/AUT20M-en- V1.1 4/17 GB_
Model AUT20 and AUT20M
20A s Automotive Current Tester
Features
Large digit LCD display
For use on standard ATC blade size fuse circuits (AUT20)
or mini- ) blade size fuse circuits (AUT20M
Measuring range (10 sec. test time max.)to 20A/48VDC
Safety
WARNING: Risk of Electrocution. Keep hands and fingers on
the body of the probe and away from the blade tips.
CAUTION: Read, understand and follow Safety Rules and
Operating Instructions in this manual before using this
product.
Do not attempt to repair this unit. There are no user
serviceable parts.
Do not expose unit to extreme temperatures or high humidity
Do not use the unit if it is wet or damaged
Do not apply more than the rated voltage between the probe
tip and ground.
Do not operate with the case open
This symbol, adjacent to another symbol or terminal,
indicates the user the user must refer to the manual
for further information.
This symbol, adjacent to a terminal, indicates that,
under normal use, hazardous voltages may be present
Double insulation
Specifications
Range 0 to 20A DC / 48V DC
Resolution 10mA
Accuracy ± (2.0% of reading + 2 digits)
Detection distance <0.2”
Operating Temperature 0 to 50 oC (32 to 122oF)
Storage Temperature 20 to 60 - oC (-4 to 140oF)
Altitude 2000 meters (7000 ft.) maximum
Relative Humidity 80% up to 31oC (88
oF), decreasing to
50% at 50oC (122
oF)
Battery 1 x ‘A23G’ 12V battery
Dimensions/Weight 159 x 25mm (6.25 x 1” ) ) / 42g (1.5oz
Cable length 71cm (2.3 )ft.
Operating Instructions
1. With the vehicle ignition OFF, remove the fuse from the
circuit to be tested and set it aside.
2. Insert the meters fuse blades (3) into the jack from where
the fuse was removed.
3. Insert the removed fuse into the meters fuse jack (4).
4. Press the meters On/Off button (2)
5. Operate the circuit under test for up to 10 seconds only; the
LCD (1) will display the measured current.
6. When finished press the On/Off button to turn off the tester.
7. WARNING! The Fuse blade may become hot during testing.
Allow to cool before removing. Do not test > 10 seconds.
BATTERY INSTALLATION
1. To replace the battery, remove the screw from the back of
the unit and remove the cover.
2. Insert one 12V ‘A23G’ battery (observe polarity).
3. Replace the battery cover
NOTE: If the meter does not work properly, check the
battery to ensure that its fresh and properly inserted.
Battery Safety
Never dispose of batteries in a fire; batteries may explode or
leak.
Never dispose of used batteries or rechargeable
batteries in household waste.
As consumers, users are legally required to take used
batteries to appropriate collection sites, the retail
store where the batteries were purchased, or
wherever batteries are sold.
Disposal: Do not dispose of this instrument in household waste. The
user is obligated to take end- -of life devices to a designated collection
point for the disposal of electrical and electronic equipment.
Copyright © - 2013 2017 FLIR Systems, Inc.
All rights reserved including the right of reproduction in whole or in part in any form
ISO- 9001 Certified
www.extech.com

Termékspecifikációk

Márka: Extech
Kategória: Mérőberendezések
Modell: AUT20

Szüksége van segítségre?

Ha segítségre van szüksége Extech AUT20, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek




Útmutatók Mérőberendezések Extech

Extech

Extech CO230 Útmutató

12 Szeptember 2024
Extech

Extech PRC20 Útmutató

3 Szeptember 2024
Extech

Extech PRC30 Útmutató

3 Szeptember 2024
Extech

Extech SD900 Útmutató

3 Szeptember 2024
Extech

Extech PRC15 Útmutató

3 Szeptember 2024
Extech

Extech 412300A Útmutató

3 Szeptember 2024
Extech

Extech 412400 Útmutató

3 Szeptember 2024
Extech

Extech 433201A Útmutató

3 Szeptember 2024
Extech

Extech SD910 Útmutató

3 Szeptember 2024
Extech

Extech EN100 Útmutató

3 Szeptember 2024

Útmutatók Mérőberendezések

Legújabb útmutatók Mérőberendezések