Használati útmutató Elba EIC-G3602ST(BK)

Elba sütő EIC-G3602ST(BK)

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Elba EIC-G3602ST(BK) (22 oldal) a sütő kategóriában. Ezt az útmutatót 5 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/22
For The Warranty Terms & Conditions, Please Refer To Warranty Certificate
Owner’s Manual
Please read this manual carefully before
operating your set.
Retain it for future reference.
Record model number and serial number
of the set.
See the label attached on the set and
quote this information to your dealer when
you require service.
BUILT IN INDUCTION COOKER
MODEL: EIC-G3602ST(BK)
2
We recommend that you read the instructions in this owner’s manual carefully before
using it for the best performance and to extend the lifespan of your appliance, as it will
provide you with all the instructions you require to ensure its safe installation, use and
maintenance.
Safety Precautions
Edges of the appliance may be sharp, extra cautions must be paid to protect injury
cause by the sharp edges.
To ensure your safety, all electric appliances should only be installed or serviced by
qualified technician. If the supply cord is damaged, it must be replaced by the
authorized service center or similarly qualified technician in order to avoid hazard.
Do not place supply cord on the edge of table and counter, or near any heating
appliance.
In order to avoid electric shock, do not immerse supply cord, plug or other parts into
water.
Do not place the appliance near electric stove, heated oven, microwave or other heat
source.
In order to avoid burning or explosion, combustibles or flammable material (curtains,
cloth, wallpaper and others) should be kept away from the appliance.
Do not place plastic or other similar items on the cooktop.
This appliance has to be properly installed and earthed, with a connecting fuse with the
load of 15A.
The glass surface may become hot during use. Please keep away from children and
never touch the glass by bare hands.
Disconnect the appliance from the power supply and wait until it is cool before cleaning
or maintenance.
In order to avoid electric shock, never use wire brush to clean the appliance since
pieces of metal is easy to touch live part.
3
Never use metal scouring pads or sharp scrapers which will damage the glass surface
leading to broken or scratches.
In order to avoid burn or electric shock, never put too much food or metal utensils on
the cooktop.
Please make sure the function has been switched off when it is not be used and hob
unplug from the socket when you are planning not to use the appliance for long time.
Never use your oven outside the built-in cabinet.
Other purpose except cooking is not allowed.
Do not rest heavy object on the glass surface. This may damage the glass .
not cook on a broken or cracked cooktop. If the cooktop surface has been broken, Do
switch off the appliance immediately at the electrical mains and contact the service
center .
Never leave the appliance unattended when in use.
This appliance is not intended for use by persons (including children) with reduced
physical sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety.
Do not use a steam cleaner to clean your cooktop.
Do not cook the food directly on the glass surface without any cooking utensils.
4
Installation
Selection of installation equipment
1. Cut out the work surface according to the sizes shown in the drawing. For the purpose
of installation and use, a minimum of 50mm space shall be preserved around the hole.
Be sure that the thickness of the work surface is at least 30mm. Please select
heat-resistant work surface material to avoid larger deformation caused by the heat
radiation from the appliance Installation as shown below:.
Under any circumstances, make sure the hob is well ventilated and the air inlet and outlet
are not blocked. Ensure the hob is in good work condition as shown above. ing
Note: The safety distance between the hotplate and the cupboard above the
hotplate should be at least 760mm.
A(mm)
B(mm)
C(mm)
D
E
760
50 mini
30 mini
Air intake
Air exit 10 mm
5
Before locating the fixing brackets
The unit should be placed on a stable, smooth surface (use the packaging). Do not apply
force onto the controls protruding from the hob. Fix the hob on the work surface by screw
four brackets on the bottom of hob (see picture) after installation. Adjust the bracket position
to suit for different work surface’s thickness.
Connecting the hob to the mains power supply
The power supply should be connected in compliance with the relevant standard, or a
single-pole circuit breaker. The method of connection is shown below.
1. If the cable is damaged or needs replacing, this should be done by an authorized
technician using the proper tools, so as to avoid any accidents.
2. If the appliance is being connected directly to the mains supply, an omnipolar circuit
breaker must be installed with a minimum gap of 3mm between the contacts.
3. The installer must ensure that the correct electrical connection has been made and it
complies with the safety regulations.
4. The cable must not be bent or compressed and shall be checked regularly.
6
Product Overview
Top View
Control Panel
1. ON/OFF
2. Power Slider Control
3. Timer Control
4. Child Lock
5. Heating Zone
6. Boost Control
1
2
3
4
7
Using the Touch Controls
• touch, so you don’t need to apply any The controls respond to sensor pressure.
• Use the ball of your finger, not its tip.
• You will hear a beep corresponding to the sensor touch function.
• Make sure the controls are always clean, dry, and that there is no object (e.g. a utensil
or a cloth) covering them. Even a thin film of water may make the controls difficult to
operate.
Choosing the right Cookware
Do not use cookware with jagged edges or a curved base.
Make sure that the base of your pan is smooth, sits flat against the glass, and is the same
size as the cooking zone. Always centre your pan on the cooking zone.
Always lift pans off the hob do not slide, or they may scratch the glass.–
8
Using Suitable Cookware for Induction
Use cookware made from ferromagnetic materials which are compatible with the induction
principle. We recommend cookware made from cast iron, enamel coated steel or stainless
steel cookware designed for induction cooking. Pans made of glass, ceramic and stoneware
are not suitable for use in the induction zone Cookware with aluminum bottoms is not .
recommended as it can cause metallic, shiny marks to appear on the glass ceramic surface
which are difficult to remove.
To test the compatibility of the cookware
Turn on the appliance and put some water in the cookware you want to check, and then
place the cookware on a cooking zone at any power level. You will notice that the induction
cooker remain cooking. If the power display the error code the cookware is compatible , in
and unsuitable for use with induction cooking.
To obtain best results
• Cookware with thick flat bases should be chosen for the benefit of uniform heat
distribution. Avoid using cookware with rough or deformed bases.
• Use of cookware with enamel coated base can prevent the glass top from getting
scratched.
• Always use pans with a diameter large enough to cover the cooking zone fully to
achieve even cooking and more efficient heat distribution.
9
Using your Induction Hob
To start cooking
After power on, the buzzer beeps once. All the indicators light up for 1 second then go out.
Indicating the induction hob has entered the state of standby mode.
1. Touch the ON/OFF control. A the indicators s - .ll how “ “
2. Place a suitable pan on the cooking zone that you wish to use. Make sure the bottom of
the pan and the surface of the cooking zone are clean and dry.
3. Touch the heating zone selection control.
4. Select a heat setting by sliding the control panel. If you don’t choose a heat setting
with minute, the induction hob will automatically switch off You will need to start in 1 .
again at step 1. You can modify the heat setting at any time during cooking. By slide to
left or right direction, the value will adjust up or down.
10
When you have finished cooking
1. Touching the heating zone selection control that you wish to switch off.
2. Turn the cooking zone off by slide to left to area . “0” until display show “0”
3. Turn the whole cooktop off by touching the ON/OFF control.
4. Beware of hot surfaces will show which cooking zone is hot to touch. It will disappear . “H”
when the surface has cooled down to a safe temperature. It can also be used as an
energy saving function if you want to heat further pans, use the hotplate that is still hot.
11
Using the boost function
1. Select the zone with boost function required.
2. Touch boost control until p ower level indication shows “P”.
*Boost function is only last for 5 minutes, after that the boost zone will go back to level 9
automatically.
Cancel the boost function
1. Select the zone with boost function.
2. Touch the slider bar to cancel the boost function and select the level you want to set.
12
Locking the Controls
• You can lock the controls to prevent unintended use (for example children accidentally
turning the cooking zones on).
• When the controls are locked, all the controls except the ON/OFF control are disabled.
To lock the controls
Touch and hold the key lock button . The timer indicator will show “Lo“
To unlock the controls
1. Make sure the induction hob is turned on.
2. Touch and hold the key lock control for 3 seconds.
3. You can now start using your induction hob.
When the hob is in the lock mode, all the controls are disable except the ON/OFF function.
You can always turn the hob off with the ON/OFF control in an emergency, but you shall
unlock the hob first in the next operation.
Residual Heat Warning
When the hob has been operating for some time, there will be some residual heat. The letter
“ ”H will appear to warn you to keep away from the glass surface.
Auto Shutdown
This safety feature occurs whenever you forget to switch off the cooking zone. The default
shutdown times are shown in the table below:
Power Level
1
2
3
4
5
6
7
8
9
Default working timer (hour)
8
8
8
4
4
4
2
2
2
13
Using the Timer
You can use the timer in two different ways:
• Use it as a minute minder. In this case, the timer will not turn any cooking zone off when
the set time is up.
• Use it to turn off after the set time is up. You can set the timer for up to 99 minutes.
Using the Timer as a Minute Minder
If you are not selecting any cooking zone
1. Make sure the cooktop is turned and the zone selection key is not activated (zone on
indicator show “ ”- and not blinking)
2. Touch the timer control, will show in the “10” timer display. “0” will flash and ready to set
the timer.
3. Set the timer setting by sliding the controls to right. Now the timer will from 10 minutes
become 15 minutes.
4. Touching timer control again, the first digit will flash and ready to set the timer.
5. Set the timer setting by sliding the controls to right. Now the timer will from 15 minutes
become 95 minutes.
14
6. When the time is set, it will begin to count down immediately. The display will show the
remaining time.
7. Buzzer will beep for 30 seconds and the timer indicator shows - - when the setting time “ ”
finished.
Setting the timer to switch off one or more cooking zones
If you are selected any cooking zone
1. Touching the heating zone selection control that you want to set the time.
2. Touch the timer control, “10” will show in the timer display. “0” will flash and ready to set
the timer.
3. Set the timer setting by sliding the controls to right. Now the timer will from 10 minutes
become 15 minutes.
4. Touching timer control again, the first digit will flash and ready to set the timer.
15
8. Set the timer setting by sliding the controls to right. Now the timer will from 15 minutes
become 95 minutes.
9. When the time is set, it will begin to count down immediately. The display will show the
remaining time.
10. There will be a red dot in the right bottom corner of power indicator which indicate that
zone has been selected.
11. When cooking timer is end, the corresponding cooking zone will be switch off
automatically.
If the timer is set on more than one zone
1. When you set the timer for several cooking zone, the red dot of the related cooking zone
are indicated. The timer display show the “minutes” count down for the shortest timer
zone and show the longest timer once the first one finished.
2. For example, the left zone has been set to power 3 level, 15 minutes timer and right
zone, power 6 level, 45 minutes timer. The timer display will show the shortest timer and
flash the indicator as left zone.
3. Once the left zone timer has end, the corresponding zone will switch off. Then the right
zone will show a new timer and the dot of the right zone will flash again.
16
Cancel the timer
1. Touch the heating zone selection control that you wish to cancel the timer.
2. Touch the timer control and the indicator will flash.
3. Touch the slider control to set the timer to “00” then the timer will be cancelled.
Cooking Guidelines
Take care when frying as the oil and fat heat up very quickly, particularly at high
power levels. At extremely high temperatures oil and fat will ignite spontaneously
and this presents a serious fire risk.
Cooking Tips
• When food comes to boil, reduce the temperature setting.
• Using a lid will reduce cooking times and save energy by retaining the heat.
• Minimize the amount of liquid or fat to reduce cooking times.
• Start cooking on high setting and reduce the setting when the food has heated through.
Simmering
• around 85˚ Simmering occurs below temperature C. When bubbles are just rising
occasionally to the surface of the cooking liquid. It is the key to delicious soups and
tender stews because the flavour develops without overcooking the food.
• You should also cook egg-based and flour-thickened sauces below boiling point.
• Some tasks including cooking rice by the absorption method may require a setting
higher than the lowest setting to ensure the food is cooked properly in the time
recommended.
17
Searing steak
To cook juicy flavour steaks:
1. Defrost the meat at room temperature for about 20 minutes before cooking.
2. Heat up a heavy-based frying pan.
3. Brush both sides of the steak with oil. Drizzle a small amount of oil into the hot pan and
then lower the meat onto the hot pan.
4. Turn the steak only once during cooking. The exact cooking time will depend on the
thickness of the steak and how cooked you want it. Times may vary from about 2 to 8
minutes per side. Press the steak to gauge how cooked it is the firmer it feels the more –
‘well done’ it will be.
5. eav L e the steak to rest on a warm plate for a few minutes to allow it to relax and
become tender before serving.
For stir-frying
1. Choose a compatible flat-based wok or a large frying pan.
2. Have all the ingredients and equipment ready. Stir-frying should be quick. If cooking
large quantities, cook the food in several smaller batches.
3. oil. Preheat the pan briefly and add two tablespoons of cooking
4. Cook any meat first , put it aside and keeps it warm. ly
5. Stir-fry the vegetables. When they are hot but still crisp, turn the cooking zone to a lower
setting, return the meat to the pan and add your sauce.
6. Stir the ingredients gently to make sure they are heated through before serving.
18
Heat Settings
The settings below are reference guidelines only. The exact setting will vary depending on
several factors, including your cookware and the amount of food you are cooking.
Experiment with the hob to find the best settings that suit you.
Heat Setting
Purpose
1 - 2
• delicate warming for small amounts of food
• melting chocolate, butter, and foods that burn quickly
• gentle simmering
• slow warming
3 - 4
• reheating
• rapid simmering
• cooking rice
5 - 6
• pancakes
7 - 8
• saute ing
• cooking pasta
9
• stir-frying
• searing
• bringing soup to the boil
• boiling water
Error Code
If an abnormal situation come up, the induction zone will enter the protective status
automatically and display corresponding code as below:
Error Code
Possible causes
What to do
E2/E3
Abnormal supply voltage
Please inspect the supply voltage and
power on after the power supply is
normal.
E4/E5
Temperature sensor failure
Please contact technician.
E6/E9
Bad induction hob heat radiation
Please restart after the induction hob
cools down.
E7/E8
Temperature sensor IBGT failure
Please contact technician.
19
Cleaning and Maintenance
What?
How?
Important!
Everyday soiling on
glass (fingerprints,
marks, stains left by
food or non-sugary
spillovers on the glass)
1. Switch off the power.
2. Apply a cooktop cleaner while the
glass is still warm. (Not hot!)
3. Rinse and wipe dry with a clean
cloth or paper towel.
4. Switch the power to the cooktop
back on.
When the power is switched off, there
will be no ‘hot surface’ indication but
the cooking zone may still be hot! Take
extreme care.
Heavy duty scourers, some nylon
scourers and harsh/abrasive cleaning
agents may scratch the glass. Always
read the label to check if the cleaner or
scourer used is suitable.
Never leave cleaning residue on the
cooktop. The glass may become
stained.
Boil overs, melts, and
hot sugary spills on the
glass surface.
Remove these immediately palette
knife or razor blade scraper suitable
for glass cooktops, but beware of
hot cooking zone surfaces:
1. Switch off the power of the
cooktop from the wall socket.
2. Hold the blade or utensil at a 30°
angle and scrape the soiling or
spill to a cool area of the cooktop.
3. Clean the soiling or spill up with a
dish cloth or paper towel.
4. Follow steps 2 to 4 for Everyd “ay
soiling on glass above. ”
Remove stains left by melts and
sugary food or spillovers as soon as
possible. If left to cool on the glass,
they may be difficult to remove or even
permanently damage the glass
surface.
Cut hazard: When the safety cover is
retracted, the blade in a scraper is
razor-sharp. Use with extreme care
and always store safely and out of
reach of children.
Spill overs on the
touch controls
1. Switch off the power of the
cooktop.
2. Soak up the spill.
3. Wipe the touch control area with
a clean damp sponge or cloth.
4. Wipe the area completely dry
with a paper towel.
5. Switch the power to the cooktop
back on.
The cooktop may beep and turn itself
off, and the touch controls may not
function while there is liquid on them.
Make sure you wipe the touch control
area dry before turning the cooktop
back on.

Termékspecifikációk

Márka: Elba
Kategória: sütő
Modell: EIC-G3602ST(BK)

Szüksége van segítségre?

Ha segítségre van szüksége Elba EIC-G3602ST(BK), tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók sütő Elba

Elba

Elba Excellence EW 965 M Útmutató

4 Szeptember 2024
Elba

Elba Elementum E 5 XLX G Útmutató

4 Szeptember 2024
Elba

Elba Elementum ENF60-444 XD Útmutató

4 Szeptember 2024
Elba

Elba Elementum ENS60-310 XD Útmutató

4 Szeptember 2024
Elba

Elba Elio EIN 32 Útmutató

4 Szeptember 2024
Elba

Elba Elio EIN 600 Útmutató

4 Szeptember 2024
Elba

Elba Elio ELIO 95-545 CG Útmutató

4 Szeptember 2024
Elba

Elba Elio ELIO 65-444 L Útmutató

4 Szeptember 2024
Elba

Elba Alterum EN95-565 XD Útmutató

4 Szeptember 2024
Elba

Elba Alterum ENS65-444 XD Útmutató

4 Szeptember 2024

Útmutatók sütő

Legújabb útmutatók sütő

Zanussi

Zanussi BMW 15 Útmutató

7 Április 2025
AEG

AEG BP9304001 Útmutató

7 Április 2025
Whirlpool

Whirlpool AKZ 116 IX S Útmutató

7 Április 2025
Atag

Atag ox 6011 m Útmutató

7 Április 2025
Thetford

Thetford XL-SOV10 series Útmutató

7 Április 2025
Smeg

Smeg cs19ida 6 Útmutató

7 Április 2025
Opera

Opera Fonda 800 DFO80B1 Útmutató

7 Április 2025
Zanussi

Zanussi zob 881 q x n w al Útmutató

6 Április 2025
Bosch

Bosch HBA74S460E Útmutató

6 Április 2025
Whirlpool

Whirlpool akp 767 nb Útmutató

6 Április 2025