Használati útmutató Digital Watchdog MegaPix IVA+ DWC-MV82WIATW

Digital Watchdog Térfigyelő kamera MegaPix IVA+ DWC-MV82WIATW

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Digital Watchdog MegaPix IVA+ DWC-MV82WIATW (2 oldal) a Térfigyelő kamera kategóriában. Ezt az útmutatót 4 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF

Oldal 1/2

MEGApix® IVA+™ models 5MP models 2.1MP models

DWC-MPV85WiATW DWC-MV85WiAT DWC-MV82WiAT

DWC-MPV82WiATW DWC-MV85WiATW DWC-MV82WiATW

DWC-MV82DiVT

Resetting the camera: To reset the

camera, use the tip of a paper clip

or a pencil and press the reset

button. Pressing the button for

ﬁve (5) seconds will initiate a

camera-wide reset of all the

settings, including network settings.

Quick Start Guide Quick Start Guide

1. The mounting surface must withstand ﬁve times the camera weight.

2. Do not let the cables get caught in improper places or the electric line

cover can be damaged. This may cause a short or ﬁre.

3. CAUTION: These servicing instructions are for use by qualiﬁed service

personnel only. To reduce the risk of electric shock do not perform any

servicing other than that contained in the operating instructions unless

you are qualiﬁed to do so.

4. CAUTION: There is a risk of explosion if the battery is replaced

incorrectly and it should be replaced only with the same battery.

ATTENTION: Il y a risque d’explosion si la batterie est remplacée par

une batterie de type incorrect. Mettre au rebut les batteries usages

conformément aux instructions.

5. Used batteries must be disposed of according to local regulations or

the battery manufacturer’s instructions. Disposing of batteries in a ﬁre

or in a hot oven, or mechanically crushing and cutting them may cause

an explosion.

6. Leaving the battery in very high temperature or low air pressure

environments may result in an explosion or leak of ﬂammable liquids

or gases.

7. This product is intended to be supplied by a UL Listed Power

Supply Unit marked “Class 2” or “LPS” or “PS2” and rated 12

Vdc, 0.62A (DWC-MPV85WiAT and DWC-MV85WiAT), 0.54A

(DWC-MPV82WiAT and DWC-MV82WiAT) and 0.36A

(DWC-MV82DiVT) min.

8. The wired LAN hub providing power over the Ethernet (PoE) in

accordance with IEEE 802-3af shall be a UL Listed device with the

output evaluated as a Limited Power Source as deﬁned in UL60950-1 or

PS2 as deﬁned in UL62368-1.

9. Unit is intended for installation in a Network Environment 0 as deﬁned

in IEC TR 62102. As such, associated

Ethernet wiring shall be limited to inside

the building.

10. For the installation process, remove the

dome cover from the camera module

by loosening the three (3) screws on

the dome. Use the wrench provided

with the camera.

11. Install the moisture packet in the

base of the camera’s lens.

• Remove the moisture absorber

from the packaging.

• Cut the card and folder along the dotted line.

• Place the moisture absorber behind the

camera’s lens module.

12. Remove the protective ﬁlm between

the dome and the camera module.

13. Remove the screw hole caps as shown

in the image below. If you are mounting

the camera using the mounting plate, do

not remove these screws.

14. Using the mounting template sheet or the

camera itself, mark and drill the

necessary holes in the wall or ceiling.

Pass the wires through and make all the necessary connections.

1. NETWORK CONNECTIONS – If you are using a PoE Switch, connect

the camera using an Ethernet cable for both data and power.

2. NETWORK CONNECTIONS – If you are using a non-PoE switch,

connect the camera to the switch using an Ethernet cable for data

transmission and use a power adapter to power the camera.

STEP 1 – PREPARING TO MOUNT THE CAMERA

STEP 3 – INSTALLING THE CAMERA

STEP 2 – POWERING THE CAMERA

1. Attach the camera to the mounting surface.

2. For soft installation surfaces, use the included metal mount plate. Fix

the mount plate on the mounting surface using the included screws.

Then, press the bottom case onto the mount plate. The three bezels on

the case will align and snap lock onto the plate.

3. To use the camera’s waterproof wiring:

a. Install the LAN cable into .

b. will be assembled

to with a 1/4 turn.

c. Thread tightly to .

4. Once the installation is complete,

remove the protective ﬁlm from

the camera’s dome cover.

5. Assemble the dome cover over the

camera body and detach the protecting ﬁlm from the dome bubble.

NOTE: To ensure moisture seal, make sure the o-ring is in place

between and . In extreme environments use of an

outdoor rated sealer is recommended.

NOTE: When using the waterproof cap, crimp the RJ45

connector after passing the cable through the

waterproof cap.

Tel: +1 (866) 446-3595 / (813) 888-9555

Technical Support Hours:

9:00 AM – 8:00 PM EST, Monday through Friday

digital-watchdog.com

Attention: This document is intended to serve as a quick reference for the

initial setup. It is recommended that the user read the entire instruction manual

for complete and proper installation and usage.

NOTE: Download all your support materials and tools in one place

1. Go to: http://www.digital-watchdog.com/resources

2. Search your product by entering the part number in the

search bar. Results for applicable ‘Search by Product’

part numbers will populate automatically based on the

part number you enter.

3. Click . All supported materials, including manuals ‘Search’

and quick start guide (QSGs) will appear in the results.

WHAT’S IN THE BOX

Mounting

Bolts and

Nuts

1 set

Mounting

Template for

Metal Plate

Installation

Metal

Mounting

Plate

Quick Setup

and

Installation

Guides

1 set

Star Wrench 1

Moisture

Absorber

and Absorber

Guide

1 set

Screws and

Plastic

Anchors-

3pcs

1 set

Waterproof

Cap and

Gasket

1 set

Mounting

Template a

Bolt and Nut

Installation

Test Video

Cable

DWC-MV85WiAT,

DWC-MV82WiAT

only

Protec�on

Film

Mounting Template

Default Login Information: admin | admin

When logging into the camera for the ﬁrst time, you will be prompted

to set up a new password. You can set the new password using the

DW® IP Finder™ software or directly from the camera’s browser menu.

Models Power requirements Power consumption

DWC-MPV85WiATW

DWC-MV85WiATW

DWC-MV85WiAT

DC 12V, PoE IEEE 802.3af

Class 3.

(Adapter not included)

DC12V: max7.4W

PoE: max8.7W

DWC-MPV82WiATW

DWC-MV82WiATW

DWC-MV82WiAT

DC12V: max 6.5W

PoE: max 8.5W

DWC-MV82DiVT DC12V: max 4.3W

PoE: max 6.2W

Ethernet

Cable

Power

Ethernet

Cable

Rev: 01/21

Speciﬁcations and pricing are subject to change without notice.

STEP 3 – INSTALLING THE CAMERA (CONT.)

Installation using Mount Bolt and Screws:

1. Using the mounting template, mark and drill the holes on the mounting

surface.

2. Secure the two long mounting screws to the camera’s base.

3. Pass the wires through the mount bracket and make all

necessary connections.

4. Mount the camera to the mounting surface by using the 2 mounting

nuts. Rotate the locking discs over the screws until the camera is held

tightly from the mounting surface.

WARNING DO NOT TOUCH THE SURFACE OF THE

BUBBLE. CleanView™ Hydrophobic Dome

Coating has been applied to the camera’s dome.

Quick Start Guide

STEP 4 – CABLING

STEP 5 – MANAGING THE SD CARD

N.C

Activation

N.O In 1

COM

In 1

COM

In 1

COM

In 1

COM

3Audio In

6Alarm

4Audio Out

5Alarm Out

2Network

1Power

The following models include a local SD card slot:

DWC-MV85WiAT, DWC-MV82WiAT

1. To install the camera’s SD Card, locate the SD card

slot in the back of the camera module.

2. Insert a class 10 SD card into the SD card slot by

pressing the SD card slot.

3. To remove the SD Card, press the card inward to

release from the card slot.

DI (+)

DI ( - )

DO ( - )

DO (+)

WHITE

YELLOW

SKY BLUE

GRAY + DOT

STEP 6 – DW® IP FINDER™

Thumbnail view

Firmware version

DHCP status

Camera’s uptime

Open IP conﬁguration

settings

Ping camera

Port information

Gateway address

Netmask address

Camera’s MAC address

Filter results

Scan network

Select network to scan

Show/hide thumbnail view

Refresh thumbnail view

Bulk password assignment

Bulk IP assignment

Firmware upgrade

Camera’s name

Camera’s IP address

Part number

Use the DW IP Finder software to scan the network and detect all MEGApix® cameras, set the camera’s network settings or access the camera’s web client.

Network Setup

1. To install the DW IP Finder, go to

http://www.digital-watchdog.com

2. Enter “DW IP Finder” on the search box at the top of the page.

3. Go to the “Software” tab on the DW IP Finder page to download

the installation ﬁle.

4. Follow the installation to install the DW IP Finder. Open the

DW IP Finder and click ‘Scan Devices’. It will scan the selected

network for all supported devices and list the results in the

table. During the scan, the DW® logo will turn gray.

‘Port forwarding’ has to be set in your

network’s router for external access

to the camera.

Select DHCP to allow the camera to receive its IP address

automatically from the DHCP server.

Select “Static” to manually enter the camera’s IP address, (Sub)

Netmask, Gateway and DNS information.

* The camera’s IP must be set to Static if connecting to

Spectrum® IPVMS

Contact your network administrator for more information.

Default TCP/IP information: DHCP

5. When connecting to the camera for the ﬁrst time, a password

must be set. To set up a password for your new camera:

a. Check the box next to your new camera from the IP Finder’s

search results. You can select multiple cameras.

b. Click “Bulk Password Assign” on the left.

c. In the pop-up window, enter admin/

admin in the current username and

password ﬁelds. Enter a new

username and password to the right.

d. Press “change” to apply all changes.

6. Select a camera from the list by

double-clicking on the camera’s image

or clicking on the ‘Click’ button under

the IP Conf. column. The pop-up

window will show the camera’s current

network settings, allowing admin users

to adjust the settings as needed.

7. To access the camera’s web page, go

to the IP Conﬁg page and click on the

‘View Camera Website’.

8. To save the changes made to the

camera’s setting, input the username

and password of the camera and

click Apply.

The following models include I/O and audio inputs and outputs:

DWC-MPV85WiAT, DWC-MV85WiAT, DWC-MPV82WiAT and

DWC-MV82WiAT

STEP 7 – WEB VIEWER

The GUI display may dier by camera models.

NOTE: Some menu options may not be available based on the

camera model. See the full manual for more information.

NOTE: 32bit version of the VLC player must be installed. If you are

using a 64bit system, uninstall the previous 64bit version

and reinstall using the 32bit version.

Once the camera’s network settings have been setup properly, you can

access the camera’s web viewer using the DW IP Finder.

To open the camera’s web viewer:

1. Find the camera using the DW IP Finder.

2. Double-click on the camera’s view in the results table.

3. Press the ‘View Camera Website’. The camera’s web viewer will

open up in your default web browser.

4. Enter the camera’s username and password you setup in the DW IP

Finder. If you did not setup a new username and password via the

DW IP Finder, you will not be able to view video from the camera.

A message will direct you to setup a new password for the camera

to view video.

5. When accessing the camera for the ﬁrst time, install the VLC player

for web ﬁles to view video from the camera.

Termékspecifikációk

Márka:	Digital Watchdog
Kategória:	Térfigyelő kamera
Modell:	MegaPix IVA+ DWC-MV82WIATW

Szüksége van segítségre?

Ha segítségre van szüksége Digital Watchdog MegaPix IVA+ DWC-MV82WIATW, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek

Az Ön neve*

Az Ön e-mail címe*

Írja ide kérdését

Útmutatók Térfigyelő kamera Digital Watchdog

Digital Watchdog MegaPix CaaS DWC-MB44WI650C1 Útmutató

11 Január 2025

Digital Watchdog Star-Light Plus DWC-B6853WTIR Útmutató

27 Augusztus 2024

Digital Watchdog MegaPix DWC-MVT4WiA Útmutató

27 Augusztus 2024

Digital Watchdog DW-VMAXD1 Útmutató

27 Augusztus 2024

Digital Watchdog DWC-MC352 Útmutató

27 Augusztus 2024

Digital Watchdog Star-Light DWC-V4363TIR Útmutató

27 Augusztus 2024

Digital Watchdog MegaPix IVA+ DWC-MPV85WIATW Útmutató

27 Augusztus 2024

Digital Watchdog Star-Light Plus DWC-B6563WTIR650 Útmutató

27 Augusztus 2024

Digital Watchdog MegaPix CaaS DWC-MF4WI4C2 Útmutató

27 Augusztus 2024

Digital Watchdog Star-Light Flex DWC-VS753WT Útmutató

27 Augusztus 2024

Útmutatók Térfigyelő kamera

Legújabb útmutatók Térfigyelő kamera

Hikvision DS-2CE10DF8T-FSLN Útmutató

6 Április 2025

Hikvision DS-2CE56C0T-IRPF Útmutató

5 Április 2025

Hikvision DS-2CD2141G1 Útmutató

5 Április 2025

Dahua Technology Pro IPC-HDPW5442G-Z Útmutató

15 Január 2025

Toshiba IKS-WR7412 Útmutató

14 Január 2025

Flir FC-610 O Útmutató

13 Január 2025

AVerMedia FC1320-P Útmutató

13 Január 2025

Digitus OptiMax DN-16037 Útmutató

13 Január 2025

Hikvision DS-2CE59U1T-AVPIT3ZF Útmutató

13 Január 2025

Hikvision IDS-2CD7526G0-IZHSY Útmutató

13 Január 2025