Használati útmutató DeWalt DWS779

DeWalt Fűrészgép DWS779

Olvassa el alább 📖 a magyar nyelvű használati útmutatót DeWalt DWS779 (60 oldal) a Fűrészgép kategóriában. Ezt az útmutatót 4 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/60
DWS779
12" (305 mm) Double Bevel Sliding Compound Miter Saw
Scie coulissante à onglet mixte 305 mm (12 po)
Sierra ingletadora compuesta deslizante de doble bisel de
305mm (12pulg.)
INSTRUCTION MANUAL
GUIDE D’UTILISATION
MANUAL DE INSTRUCCIONES
INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE
GARANTÍA. : ADVERTENCIA LÉASE ESTE INSTRUCTIVO ANTES DE
USAR EL PRODUCTO.
Questions? Visit us at www.dewalt.com
Des questions ? Rendez nous visite à www.dewalt.com
¿Tiene preguntas? Visítenos en www.dewalt.com
Before returning this product call
1-800-4-
DeWALT
IF YOU SHOULD EXPERIENCE A PROBLEM WITH YOUR D
e
WALT PURCHASE,
CALL 1-800-4-D
e
WALT
IN MOST CASES, A D
e
WALT REPRESENTATIVE CAN RESOLVE
YOUR PROBLEM OVER THE PHONE.
IF YOU HAVE A SUGGESTION OR COMMENT, GIVE US A CALL.
YOUR FEEDBACK IS VITAL TO THE SUCCESS OF D
e
WALT’S
QUALITY IMPROVEMENT PROGRAM.
Final Print Size: 11 x 8.5 inches
English
1
Definitions: Safety Guidelines
The definitions below describe the level of severity for each signal word. Please read the
manual and pay attention to these symbols.
DANGER: will Indicates an imminently hazardous situation which, if not avoided,
result in death or serious injury.
WARNING: Indicates a potentially hazardous situation which, if not avoided, could
result in death or serious injury.
CAUTION: Indicates a potentially hazardous situation which, if not avoided, may
result in minor or moderate injury.
NOTICE: Indicates a practice which, if not avoided, not related to personal injury
may result in property damage.
IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY D
e
WALT TOOL,
CALL US TOLL FREE AT: 1-800-4-D
e
WALT (1-800-433-9258).
WARNING: To reduce the risk of injury, read the instruction manual.
Important Safety Instructions
WARNING! Read all safety warnings and all instructions. Failure to follow the
warnings and instructions may result in electric shock, fire and/or serious injury.
SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTURE REFERENCE
Double Insulation
Double insulated tools are constructed throughout with two separate layers of electrical
insulation or one single layer of reinforced insulation between you and the tool’s electrical
system. Tools built with this insulation system are not intended to be grounded. As a result,
your tool is equipped with a two prong plug which permits you to use extension cords without
concern for maintaining a ground connection.
NOTE: Double insulation does not take the place of normal safety precautions when
operating this tool. The secondary insulation system is for protection against injury resulting
from a possible failure of the primary insulation within the tool.
CAUTION: WHEN SERVICING USE ONLY IDENTICAL REPLACEMENT PARTS. Repair or
replace damaged cords.
Polarized Plugs
Polarized plugs (one blade is wider than the other) are used on equipment to reduce the risk
of electric shock. When provided, this plug will fit in the polarized outlet only one way. If the
plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified
electrician to install the proper outlet. Do not change the plug in any way.
Safety Instructions for All Tools
WARNING: To reduce the risk of eye injury, use eye protection when ALWAYS
operating the miter saw.
• KEEP GUARD IN PLACE and in working order.
• REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that
keys and adjusting wrenches are removed from spindle before turning tool on. Tools, scrap
pieces, and other debris can be thrown at high speed, causing injury.
• KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents.
• DO NOT USE THE MACHINE IN A DANGEROUS ENVIRONMENT. The use of power
tools in damp or wet locations or in rain can cause shock or electrocution. Keep your work
area well-lit to avoid tripping or placing arms, hands, and fingers in danger.
• KEEP CHILDREN AWAY. All visitors should be kept at a safe distance from work area.
Your shop is a potentially dangerous environment.
• MAKE WORKSHOP CHILDPROOF with padlocks, master switches, or by removing
starter keys. The unauthorized start-up of a machine by a child or visitor may result in injury.
• DON’T FORCE TOOL. It will do the job better and be safer at the rate for which it was
designed.
• USE RIGHT TOOL. Don’t force tool or attachment to do a job for which it was not
designed. Using the incorrect tool or attachment may result in personal injury.
• WEAR PROPER APPAREL. Do not wear loose clothing, gloves, neckties, rings,
bracelets, or other jewelry which may get caught in moving parts. Nonslip footwear is
recommended. Wear protective hair covering to contain long hair.
• ALWAYS USE SAFETY GLASSES. Everyday eyeglasses are NOT safety glasses. Also
use face or dust mask if cutting operation is dusty. ALWAYS WEAR CERTIFIED SAFETY
EQUIPMENT:
• ANSI Z87.1 eye protection (CAN/CSA Z94.3).
• ANSI S12.6 (S3.19) hearing protection.
• NIOSH/OSHA/MSHA respiratory protection.
• SECURE THE WORKPIECE. Use clamps or a vise to hold the workpiece on the table
and against the fence or when your hand will be dangerously close to the blade within 6"
(152mm). It is safer than using your hand and it frees both hands to operate tool.
• DON’T OVERREACH. Keep proper footing and balance at all times. Loss of balance may
cause personal injury.
• MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and safest
performance. Follow instructions for lubricating and changing accessories. Poorly
maintained tools and machines can further damage the tool or machine and/or cause
injury.
• TURN THE MACHINE “OFF”, AND DISCONNECT THE MACHINE FROM THE
POWER SOURCE before installing or removing accessories, before adjusting or changing
set-ups, when making repairs or changing locations. An accidental start-up can cause
injury. Do not touch the plug’s metal prongs when unplugging or plugging in the cord.
• REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure that the switch is in
the “OFF” position before plugging in the power cord.
• USE PROPER EXTENSION CORD. Make sure your extension cord is in good condition.
When using an extension cord, be sure to use one heavy enough to carry the current your
product will draw. An undersized cord will cause a drop in line voltage resulting in loss of
power and overheating. The following table shows the correct size to use depending on
cord length and nameplate ampere rating. If in doubt, use the next heavier gauge. The
smaller the gauge number, the heavier the cord.
Minimum Gauge for Cord Sets
Ampere Rating
Volts Total Length of Cord in Feet (meters)
120V 25 (7.6) 50 (15.2) 100 (30.5) 150 (45.7)
240V 50 (15.2) 100 (30.5) 200 (61.0) 300 (91.4)
More
Than
Not More
Than AWG
0 6 18 16 16 14
6 10 18 16 14 12
10 12 16 16 14 12
12 16 14 12 Not Recommended

Termékspecifikációk

Márka: DeWalt
Kategória: Fűrészgép
Modell: DWS779

Szüksége van segítségre?

Ha segítségre van szüksége DeWalt DWS779, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók Fűrészgép DeWalt

DeWalt

DeWalt DCCS621 Útmutató

3 Január 2025
DeWalt

DeWalt DCPS671 Útmutató

3 Január 2025
DeWalt

DeWalt DCS590 Útmutató

3 Január 2025
DeWalt

DeWalt DWM120 Útmutató

2 Október 2024
DeWalt

DeWalt DW309K Útmutató

30 Szeptember 2024
DeWalt

DeWalt DW317 Útmutató

30 Szeptember 2024
DeWalt

DeWalt DW100 Útmutató

23 Szeptember 2024
DeWalt

DeWalt DW861 Útmutató

12 Szeptember 2024
DeWalt

DeWalt DCS312B Útmutató

10 Szeptember 2024
DeWalt

DeWalt DCS397 Útmutató

2 Szeptember 2024

Útmutatók Fűrészgép

Legújabb útmutatók Fűrészgép

Bavaria By Einhell

Bavaria By Einhell BHS 66 Útmutató

3 Április 2025
Bavaria By Einhell

Bavaria By Einhell BPS 600 E Útmutató

3 Április 2025
Makita

Makita DCS4610 Útmutató

2 Április 2025
Makita

Makita DPC6430 Útmutató

1 Április 2025
Makita

Makita DCS431 Útmutató

1 Április 2025
Makita

Makita DCS430 Útmutató

1 Április 2025
Makita

Makita EK6101 Útmutató

1 Április 2025
Makita

Makita DCS6401 Útmutató

1 Április 2025
Kraftronic

Kraftronic KT-ST 550 Útmutató

30 Március 2025
Kraftronic

Kraftronic KT-US 650 Útmutató

30 Március 2025