Használati útmutató Dahua Technology HAC-HFW2241TU-A-POC

Dahua Technology Térfigyelő kamera HAC-HFW2241TU-A-POC

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Dahua Technology HAC-HFW2241TU-A-POC (12 oldal) a Térfigyelő kamera kategóriában. Ezt az útmutatót 4 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF

Oldal 1/12

HDCVI Camera

User’s Manual

V1.0.

III

Important Safeguards and Warnings

Electrical Safety

 All installation and operation should conform to your local electrical safety codes.

 The power supply must conform to the requirements of ES1 in IEC 62368-1 standard and be no

higher than PS2. Note that the power supply requirements are subject to the device label.

 A readily accessible disconnect device shall be incorporated in the building installation wiring.

 Make sure that the power adapter meets the operating voltage requirement before device

powering up the device (The material and length of the power cable might influence the device

voltage).

 Prevent the power cable from being trampled or pressed, especially the plug, power socket and

the junction extruded from the device.

 We assume no liability or responsibility for all the fires or electrical shock caused by improper

handling or installation.

Operating Requirements

 Do not aim the device at strong light to focus, such as lamp light and sun light.

 Transport, use and store the device within the range of allowed humidity and temperature.

 Keep the device away from water or other liquid to avoid damages to the internal components.

 Keep sound ventilation to avoid heat accumulation.

 Heavy stress, violent vibration or water splash are not allowed during transportation, storage

and installation.

 Pack the device with standard factory packaging or the equivalent material when transporting

the device.

 You are recommended to use the device together with lightning arrester to improve lightning

protection effect.

 You are recommended to ground the device to enhance reliability.

 You are recommended to use qualified video transmission cable to improve video quality, and

use RG59 coaxial cable or higher standard.

WARNING

 Use standard components or accessories provided by the manufacturer and make sure that the

device is installed and maintained by professional engineers.

 The surface of the image sensor should not be exposed to laser beam radiation in an

environment where a laser beam device is used.

 Do not provide two or more power supply sources for the device; otherwise it might damage

the device.

 If PoC power supply is used, do not connect any other device between the device and PoC

transceiver including UTC, Balun, optical transceiver, distributor and convertor and so on;

otherwise, the device might get burned.

 PoC supply voltage is up to 52V. Do not dismantle the device during normal operation;

otherwise it might cause danger to both device and users due to high voltage.

Table of Contents

Foreword I.....................................................................................................................................................

Important Safeguards and Warnings ........................................................................................................ III

1 Overview ....................................................................................................................................................1

Introduction................................................................................................................................................. 1 1.1

Application ................................................................................................................................................... 1 1.2

Transmission Distance .................................................................................................................................. 2 1.3

2 Cable Connection ........................................................................................................................................3

Power Output 3 ..............................................................................................................................................2.1

12 VDC Power Input Port ............................................................................................................................. 3 2.2

24 VAC Power Input Port 3 .............................................................................................................................2.3

Video Output Port ........................................................................................................................................ 4 2.4

Audio Input Port 4 ..........................................................................................................................................2.5

Alarm Output Port ....................................................................................................................................... 4 2.6

DIP Switch .................................................................................................................................................... 5 2.7

HD/SD Switch Control Cable ........................................................................................................................ 5 2.8

HDCVI Aviation Connector ........................................................................................................................... 5 2.9

3 General Configuration and Operation ..........................................................................................................7

Entering XVR Main Menu ............................................................................................................................. 7 3.1

Setting Audio Input ...................................................................................................................................... 7 3.2

Operating PTZ Control Panel ........................................................................................................................ 8 3.3

3.3.1 Operating OSD Menu ....................................................................................................................... 8

3.3.2 Operating Auto Focus (AF) ............................................................................................................. 10

4 Full-Color Camera Configuration ................................................................................................................ 11

Enabling/Disabling Smart Light .................................................................................................................. 11 4.1

Configuring Smart Light Adjustment.......................................................................................................... 11 4.2

5 Smart Dual Illuminators Cameras Configuration ......................................................................................... 12

6 Temperature and Humidity Camera Configuration ...................................................................................... 14

Enabling/Disabling Temperature and Humidity ......................................................................................... 14 6.1

Configuring Temperature Monitoring Mode ............................................................................................. 14 6.2

Adjusting Temperature and Humidity Display ........................................................................................... 14 6.3

Viewing Temperature and Humidity .......................................................................................................... 15 6.4

7 Active Deterrence Camera Configuration ................................................................................................... 16

Detection Range of PIR Detector ............................................................................................................... 16 7.1

Configuring Trigger Mode .......................................................................................................................... 16 7.2

Configuring Light Warning and Audio Alarm ............................................................................................. 17 7.3

Configuring Smart Dual Illuminators Active Deterrence Camera .............................................................. 17 7.4

8 Gateway Camera Configuration ................................................................................................................. 20

Connecting Node Devices on OSD menu................................................................................................... 20 8.1

Connecting Node Devices on XVR.............................................................................................................. 20 8.2

9 Box Camera Installation ............................................................................................................................22

Lens Installation ......................................................................................................................................... 22 9.1

9.1.1 Installing Lens Type 1 ..................................................................................................................... 22

9.1.2 Installing Lens Type 2 ..................................................................................................................... 23

I/O Port Installation ................................................................................................................................... 24 9.2