Használati útmutató Da-Lite Flex Plex 29529

Da-Lite Vetítővászon Flex Plex 29529

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Da-Lite Flex Plex 29529 (12 oldal) a Vetítővászon kategóriában. Ezt az útmutatót 6 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Oldal 1/12
INSTRUCTION BOOK FOR
Polacoat Flex Plex Screen
2
Preparation
It requires at least four people to assemble a Flex Plex screen. To maintain optimal image geometry and screen alignment, a lat and
straight wall free from obstructions and angular distortions should be used. A wall opening with 5 + the ordered viewing height and
5+ the ordered viewing width must be used to maintain the precise in-wall it of the Flex Plex sreen. When assembling the screen,
choose a clean work area using padded material or other soft, clean materials. The work area should be larger than the overall screen
size and directly in front of the wall opening where the screen is to be installed (audience side).
NOTE: Please read through the installation steps and note wait times. The rolled screen surface needs to be acclimated to the room for
48 hours prior to installation (Step 1). Once the surface is unrolled it will need to lay in its unrolled state for (Step 2).4 hours
Screen Orientation
Polacoat® In-Wall rear projection screens have a polished surface and a matte, coated surface. The polished surface should always be
installed so that it faces the projector and the matte surface must face the audience. If screen has anti-glare coating, the anti-glare
surface should always face the projector.
Tools Required for Installation (not provided)
Screw Gun/Drill and Drill Bits 1/2" Open Wrenches
(2) Ladders
#10 x 1” Countersunk
Flat Head Screws
¼ x 1” Hex Lag Screws
1/8” & 3/16Hex Keys
Measuring Tape LevelRubber Mallet
Knife
3
Maintenance and Protection
Projection screens should always be installed after the
completion of construction, drywall, and painting of all adjacent
areas. If construction work needs to occur near an installed
screen, clean polyethylene sheeting should be used to cover and
protect both surfaces. Never apply adhesive tapes to the
coated surface. Always be careful to guard the screen against
damage from moving scafolding, ladders, or staging materials.
General Cleaning
Never use solvents on or near Da-Lite rear projection screens.
Remove dust by gently blotting the screen with a soft, clean, lint-
free cloth.
Included Hardware
(3) 30’ Ropes(4) pairs Gloves (2) 4” Pieces of Trim (1) Screen Surface
(6) Trim Pieces
(2) Hoisting Brackets (24) Tensioning Assemblies
(6) Frame Pieces (4) Rubber Gaskets(6) TTracks
(3) Lifting Brackets (4) Cap Screws
NOTE: Quantities listed are for standard sizes. Quantities will vary if a custom screen that is larger than standard is ordered.
Dry Soil Marks
Clean with VM&P Naptha or with Da-Lite Lenskleen and a soft,
clean, lint-free cloth.
Cleaning of Frame and Trim
The exposed surfaces of the aluminum frames can be cleaned
with a dilute solution of detergent and water, followed by a clear
water rinse. Use a soft, grit-free cloth to preserve the anodized
inish. Protect screen surface during frame cleaning. Do not use
abrasive cleaners or solvents.
(4) Corner Covers

Termékspecifikációk

Márka: Da-Lite
Kategória: Vetítővászon
Modell: Flex Plex 29529

Szüksége van segítségre?

Ha segítségre van szüksége Da-Lite Flex Plex 29529, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek




Útmutatók Vetítővászon Da-Lite

Útmutatók Vetítővászon

Legújabb útmutatók Vetítővászon