Használati útmutató D-Link DIS-100G-S5W

D-Link kapcsoló DIS-100G-S5W

Olvassa el alább 📖 a magyar nyelvű használati útmutatót D-Link DIS-100G-S5W (8 oldal) a kapcsoló kategóriában. Ezt az útmutatót 2 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/8
1
DIS-100E Series Unmanaged
Industrial Fast Ethernet Switch
Quick Installation Guide
O verview
The -DIS 100E Series nmanaged Industrial U Fast Ethernet
Switch solutions are designed for supporting standard
industrial applications without complex setup, allowing for
a - - truly plug and play network.
If the equipment is used in a manner not specified by the
manufacturer, the protection provided by the equipment
may be impaired.
Package Checklist
Please verify that the box contains the following items:
Item Quantity
Unmanaged switch 1
Wall-mount plates 2
DIN r 1 ail clip
M4 Screws
(for the wall mount plates &
DIN clip)
4
DC power terminal block 1
RJ-45/SFP protective cap 2-4
Quick Installation Guide 1
Safety I nstructions
When a connector is removed during installation, testing,
or servicing, or when an energized fiber is broken, a risk of
ocular exposure to optical energy that may be potentially
hazardous occurs, depending on the laser output power.
The primary hazards of exposure to laser radiation from an
optical-fiber communication system are:
Damage to the eye by accidental exposure to a beam
emitted by a laser source.
Damage to the eye from viewing a connector attached
to a broken fiber or an energized fiber.
Documentation Conventions
The following conventions are used in this quick installation
guide to emphasize information that will be of interest to
the reader.
D — ANGER The described activity or situation might or
will cause personal injury.
WARNING — The described activity or situation might
or will cause equipment damage.
C — AUTION The described activity or situation might or
will cause service interruption.
N — OTE The information supplements the text or
highlights important points.
Di mension Illustration (unit: mm)
5- Port Model
8- Port Model
2
DIN Rail- M ounting
1. Attach the DIN rail kit onto the switch using the bracket
and screws in the accessory kit.
2. Hook the unit over the DIN rail.
3. Push the bottom of the unit towards the DIN rail until it
snaps into place.
Wall M ounting (unit: mm)
1. the Attach wall mounting kit onto the switch using the
mounting plate and s M4 screws in the accessory kit.
5- Port Model
8- l Port Mode
Connecting to Ground
The switch must be properly grounded for optimum system
performance.
5- 8- Port Model Port Model
Connecting to Ethernet Interfaces
(RJ- 45)
Connecting the Ethernet interface via RJ- 45:
To connect to a PC, use a straight through or a -
cross-over Ethernet cable,
To connect the switch to an Ethernet device, use UTP
(Unshielded Twisted Pair) or STP (Shielded Twisted
Pair) Ethernet cables.
The pin assignment of the RJ-45 connector is shown in the
following figure and table.
Pin Assignment
1,2 - T/Rx+,T/Rx
3,6 R/T R/Tx- x+,
3
Ver. 1.0 )0(WW 2018/ / - 06 06 GP801010X 000
3
Connecting to Fiber Interfaces ( ) SFP
Please prepare LC connectors or SC connectors (with the
the use of an optional SC se adapters -to-LC adapter). The
are available with multimode, single mode, long haul (for -
connections up to 120+ km) or in the form of
special-application transceivers.
For each fiber port there is a transmit (TX) and receive (RX)
signal. Please make sure that the transmit (TX) port of the
switch connects to the receive (RX) port of the other device,
and the receive (RX) port of the switch connects to the
transmit (TX) port of the other device when making your
fiber optic connections.
DANGER: Never attempt to view optical connectors
that might be emitting laser energy.
Do not power up the laser product without
connecting the laser to the optical fiber and
putting the cover in position, as laser
outputs will emit infrared laser light at this
point.
Connecting the Power
The switch can be powered two powerusing supplies
(input range 12V Insert the positive and negative – . 58V)
wires into V+ and Vthe - contacts on the terminal block and
tighten the wire-clamp screws to prevent the wires from
being loosened.
N : OTE The DC power should be connected to a
properly-fused power supply.
Connecting the Alarm Relay
The alarm relay output contacts are in the middle of the DC
terminal block connector as shown in the following . figure
By inserting the wires and set the DIP switch of the Port ting
Alarm to “ ”ON , the relay output alarm will detect any port
failures, and form a short circuit.
The alarm re Normal Openla “y out is ”.
DIP Switch Setting
Pin No# 5-Status Port Model
Pin 1
ON E nable the power alarm.
OFF D isable the power alarm.
Pin 2
ON E b . nable roadcast storm rate limiting
OFF D b . isable roadcast storm rate limiting
Pin No# 8- t Status Por Model
Pin 1
ON E b . nable roadcast storm rate limiting
OFF D b . isable roadcast storm rate limiting
Pin 2
ON E nable the power alarm.
OFF D isable the power alarm.
LED STATUS INDICATIONS
LED Name
Status
Condition
P1
Solid
green
P1 power line has power.
Off
P1 power is disconnected or
is not being powered.
P2
Solid
green
P2 power line has power.
Off
P2 power disconnectedis or
is not being powered.
Alarm
Solid red
Power failure alarm
triggered.
Off
No power failure alarm.
Copper 1 to
N port
Link/Act
Solid
g reen
Ethernet link up but no traffic
is detected.
Blinking
g reen
Ethernet link up and there is
traffic detected.
Off
Ethernet link down.
Copper 1 to
N port
Speed
Solid
y ellow
A 100Mbps connection is
detected.
Off
No link, or a10Mbps
connection is detected.
SFP 1 to N
port
(N=0,1,2)
Link/Act
Solid
g reen
SFP p . ort link up
Off
SFP . link down
Additional Information
You can refer to the user manual or visit
http://support.dlink.com/ for more support.
Online Support
If there are any issues that are not in the user manual,
please visit http://support.dlink.com/ which will direct you to
your appropriate local D-Link support website.
Warranty Information
Visit http://warranty.dlink.com/ to view the D-Link Warranty
information.

Termékspecifikációk

Márka: D-Link
Kategória: kapcsoló
Modell: DIS-100G-S5W

Szüksége van segítségre?

Ha segítségre van szüksége D-Link DIS-100G-S5W, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók kapcsoló D-Link

D-Link

D-Link DIS-100G-S5W Útmutató

25 December 2024
D-Link

D-Link DPS-200 Útmutató

24 December 2024
D-Link

D-Link DES-1016R+ Útmutató

24 December 2024
D-Link

D-Link DES-1024R+ Útmutató

24 December 2024
D-Link

D-Link DES-1008F Útmutató

24 December 2024
D-Link

D-Link DES-1228 Útmutató

24 December 2024
D-Link

D-Link DGS-3630-28TC Útmutató

24 December 2024
D-Link

D-Link DXS-3130-28P Útmutató

21 December 2024
D-Link

D-Link DGS-1100-05PDV2 Útmutató

20 December 2024
D-Link

D-Link DGS-1100-05V2 Útmutató

20 December 2024

Útmutatók kapcsoló

Legújabb útmutatók kapcsoló

Smart-AVI

Smart-AVI DVN-16Pro Útmutató

24 December 2024
Smart-AVI

Smart-AVI SM-D2H-4Q Útmutató

24 December 2024
Adder

Adder View Secure AVS 2214 Útmutató

24 December 2024
Adder

Adder Link INFINITY 1102 Útmutató

24 December 2024
Adder

Adder Link INFINITY Dual 2020 Útmutató

24 December 2024
Adder

Adder Link INFINITY 2122 Útmutató

24 December 2024
Adder

Adder View 4 PRO VGA Útmutató

24 December 2024
Adder

Adder View Secure AVS 4214 Útmutató

24 December 2024
Adder

Adder View Secure AVS 4114 Útmutató

24 December 2024
Adder

Adder View Secure Útmutató

24 December 2024