Használati útmutató Ctek XS 7000

Ctek Akkumulátor töltő XS 7000

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Ctek XS 7000 (1 oldal) a Akkumulátor töltő kategóriában. Ezt az útmutatót 7 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF

Oldal 1/1

XS 7000

Battery Charger

For lead-acid batteries 14–225Ah

User’s manual and guide to

professional battery charging for

starter and deep cycle batteries.

Model 1007

INTRODUCTION

Congratulations on your purchase of your new professional XS 7000 Switch Mode Charger

with Pulse Maintenance, Float and Analysis. XS 7000 is a member of a family of professional

chargers from CTEK Sweden AB. It represents the state-of-the-art technology for battery

charging. A XS 7000 will prolong the lifetime of your battery. Read this user manual and follow

the instructions carefully before using the charger.

SAFETY

• The charger is designed for lead-acid batteries 14–225Ah. Do not use the charger for any

other purpose.

• Use safety glasses and turn your head away when connecting or disconnecting a battery.

• Battery acid is corrosive. Rinse immediately with water if acid comes into contact with skin or

eyes. Seek medical advice.

• Make sure that the cable is not being pinched or in contact with warm surfaces

or sharp edges.

• While charging, a battery can emit explosive gases, so it is important to avoid sparks in the

immediate area.

• Always provide for proper ventilation during charging.

• Avoid covering the charger.

• Make sure that the electrical cable does not come into contact with water.

• Never charge a frozen battery.

• Never charge a damaged battery.

• Do not place the charger on the battery while charging.

• The electrical connection must fulfil the national heavy current requirements.

• Check the cabling in the charger before use. Make sure there are no cracks in the cabling or

in the protective covering. A charger with damaged cables may not be used.

• Always check that the charger has gone over to maintenance charging mode before leaving

the charger unattended and connected for long periods. If the charger has not gone over

to maintenance charging within 3 days, this is an indication of a problem. In this case the

charger must be disconnected manually.

• All batteries fail sooner or later. A battery that fails during charging is normally taken care of

by the chargers advanced control, but certain uncommon errors in the battery can still arise.

Don’t leave the battery charger unattended for a longer period of time.

• Only mount the charger on a flat surface.

• This equipment may not be used by children or by those who can not read and understand

the manual if they are not supervised by a responsible person who can guarantee that the

battery charger is being used in a safe manner. Store and use the battery charger out of the

reach of children. Make sure that children do not play with the battery charger.

BATTERY TYPES

The following recommendations should only be considered as guidelines. In the event of

uncertainty always refer to the battery manufacturer’s recommendations.

XS 7000 is suitable for charging all types of 12V lead-acid batteries: open batteries, MF, AGM

and most GEL-batteries. Battery sizes 14–225Ah.

CHARGING

Charging batteries mounted in a vehicle:

1. The power cord should be disconnected before connecting or disconnecting

the battery leads.

2. Identify the pole that is grounded (attached to the chassis). Ground is normally connected to

the negative terminal.

3. Charging a negatively grounded battery. Connect the red wire to the positive pole of the

battery and the black cable to the vehicle’s chassis. Be careful not to connect the black cable in

the vicinity of a fuel pipe or the battery.

4. Charging a positively grounded battery. Connect the black wire to the negative pole of the

battery and the red cable to the vehicle's chassis. Be careful not to connect the red cable in the

vicinity of a fuel pipe or the battery.

Charging of a battery not connected to a vehicle:

1. The power cord should be disconnected before connecting or disconnecting the

battery leads.

2. Connect the red wire to the positive pole of the battery and the black cable to the

negative pole.

Connecting the provided cables with eyelet terminals:

Make sure that the cable is not being pinched or in contact with warm surfaces or sharp edges.

When the cable is mounted on the battery, it should not be connected to the charger. Connect

the eyelet terminals to the battery's poles - the red cable to the positive pole and the black cable

to the negative pole. After this, the quick contact can be connected.

Reverse Polarity Protection

If the battery cables are connected incorrectly, the reverse polarity protection will make

sure that the charger and the battery are not damaged. In this case, the red warning

lamp (0) will be lit.

Start charging

1. Connect the power cord to the power outlet.

2. The lamp for Deep Discharged battery (1) will indicate if the battery voltage is low.

If lamp 1 blinks, this indicates that the battery is lightly sulfated. Read more under

”CHARGING PHASES”

3. Normal charging is indicated by the following lamps: Deep Discharged (1), Bulk Charge

(2), Absorption Charge (3) or Maintenance Charging (4). When the maintenance lamp is lit,

the battery is fully charged. The charge will restart if the voltage drops. The charger can be

connected for months.

4. If the battery cables are connected incorrectly, the reverse polarity protection will make

sure that neither the charger nor the battery will be damaged. In this case, the red warning

lamp (0) will be lit.

5. If nothing happens. If none of the lamps come on this may be due to the connection to the

battery or chassis is poor or that the battery is faulty or has a too low terminal voltage. Another

cause may be a lack of voltage in the wall socket.

6. Charging can be interrupted at any time by disconnecting the power from the wall socket.

Always disconnect the power cable from the wall socket before removing the battery cables.

When you interrupt charging of a battery mounted in a vehicle, always disconnect the battery

cable from the chassis before removing the other battery cable.

CHARGING PHASES

XS 7000 is a multi stage fully automatic charger.

Desulphation (Lamp 1, blinking)

Desulphation with pulses to recover sulphated batteries. Indicated by blinking lamp 1.

Start (Lamp 1)

Starting phase for charging. The starting phase continues until the batter y’s terminal voltage

has risen over a preset level. At this point, charging goes into the bulk phase. If the terminal

voltage has not reached the preset level within 8 hours, charging is suspended. The error mode

is indicated. This indicates a battery which is faulty or has too large capacity. If a large battery

is charged that has been severely discharged, it may be necessary to restart the charger after 8

hours. Start is indicated by lamp 1.

Bulk (Lamp 2)

Primary charging where approximately 80% of the charging happens. The charger delivers

maximum current until the terminal voltage has risen to the preset level. After a number of

hours, the charger goes on to the next phase, even if maximum voltage is not reached. Bulk is

indicated by lamp 2.

Absorption (Lamp 3)

Final charging, voltage is kept at the preset level. During this phase, the current is gradually

reduced. If the maximum length of time for Absorption is exceeded, the charger automatically

continues with Analysis. Absorption is indicated by lamp 3.

Analysis (Lamp 3)

Charging is suspended for a short period and the battery voltage measured. If it falls too quick-

ly, the battery is probably faulty. Charging is suspended and an error is indicated (lamp 0).

Maintenance charging - float (Lamp 4)

During the first 10 days of maintenance charging the battery is maintained with constant

voltage, 13.6V. Float-maintenance is indicated by lamp 4.

Maintenance charging - pulse (Lamp 4)

Charging level varies between 95% and 100%. The battery receives a pulse when the voltage

drops, keeping the battery in good shape when it is not being used. The charger can be

connected for months.

If the battery is charged and/or the battery’s terminal voltage drops, the charger starts a charge

pulse until the voltage has reached the preset level. The charge pulse is then interrupted and

the cycle is repeated as long as the charger is in pulse maintenance phase. If the terminal

voltage drops even lower, the charger automatically reverts to the beginning of the charging

curve. Pulse maintenance phase is indicated by lamp 4. If possible, check the water level

in the battery.

TEMPERATURE PROTECTION

XS 7000 is protected from being overheated. The power will be reduced if the ambient temper-

ature is raised.

EQUIPMENT

XS 7000 is delivered with a set of battery leads with battery pole clamps and a set of battery

leads with eyelet terminals.

MAINTENANCE

The charger is maintenance free. Note that disassembly of the charger is not permitted and

will void the warranty. If the power cord is damaged, the charger must be left to the reseller for

maintenance. The case can be cleaned with a soft damp cloth and mild cleanser. The charger

should be disconnected from the power while cleaning.

WARRANTY

CTEK SWEDEN AB, Rostugnsvägen 3, SE-776 70 VIKMANSHYTTAN, SWEDEN provides

a limited warranty to the original purchaser of this product. This limited warranty is not

transferable. The unit is warranted against defective workmanship or materials for 2 years from

the date of purchase. The customer must return the product together with the original purchase

receipt to the place of purchase. This warranty is void if the unit is handled carelessly, opened

or repaired by anyone other than CTEK SWEDEN AB or its authorized representative. CTEK

SWEDEN AB makes no warranty other than this limited warranty and expressly excludes any

implied warranty including any warranty for consequential damages. This is the only expressed

limited warranty and CTEK SWEDEN AB neither assumes nor authorizes anyone to assume or

make any other obligation towards the product other than his limited warranty.

TECHNICAL SPECIFICATION

Model 1007

Voltage AC 170–260VAC, 50–60Hz

Back current drain* < 1mA

Charging voltage 14.4V (Nominal 12V)

Ripple** Max 150mV rms, max 0.3A (=4%)

Current 7A max

Ambient Temperature -20°C – +50°C, power is reduced automatically at

increased ambient temperature.

Cooling Natural convection.

Charging cycle XS 7000 is a multi stage fully automatic charger

Type of batteries All types of 12V lead-acid batteries (Wet, MF, AGM and GEL).

Battery Capacity 14–225Ah

Dimensions 191 x 89 x 48 mm (L x W x H)

Insulation IP65

Weight 0.8 kg

*) Back current drain is the current that the charger drains the battery with, if the wall socket

is disconnected.

**) Quality of the current and voltage are very important. High current ripple heats up the

battery and makes the positive electrode age prematurely. High voltage ripple could harm other

equipment connected to the battery. XS 7000 produces a high quality current and voltage with

very low ripple.

MANUFACTURERS DECLARATION

CTEK SWEDEN AB, Rostugnsvägen 3, SE-776 70 VIKMANSHYTTAN, SWEDEN. Declares

under sole responsibility that the battery charger XS 7000, to which this declaration relates is

in conformity with the following LVD standards: EN60335-1, EN60335-2-29 according to the

terms of directive 73/23/EEC with the addition of 93/68/EEC. This product also is in agreement

with the following EMC standards: EN61000-3-3, EN61000 -3-2, EN55014-1 and EN55014-2

according to the terms of directive 89/336/EEC with the addition of 92/31/EEC and 93/68/EEC.

VIKMANSHYTTAN, SWEDEN 2006-01-23

Börje Maleus, VD

CTEK SWEDEN AB,

Rostugnsvägen 3

SE-776 70 VIKMANSHYTTAN, SWEDEN

Fax: +46 225 30793

www.ctek.com

INDICATIONS

Indication Description

3 4

RESET

0 Error mode, the charger suspends the

charging / voltage maintenance. See

further description below.

1 Start mode.

2 Bulk charging, maximum voltage.

3 Absorption charging, voltage is limited.

4 Pulse maintenance charging

A Power On

Error mode

The charger enters error mode before start in the following situations:

• The battery is connected with poles reversed to the charger’s terminals.

• The terminals on the charger are short-circuited.

Error mode before start is reset by removing the error situation.

The charger enters steady error mode in the following situations:

• The charger’s analysis function has interrupted charging.

• The charger has been in start mode longer than maximum time.

Steady error mode is acknowledged/reset by pressing the ”RESET” button.

CHARGING TIME

The table shows the length of time for bulk charging.

Battery size (Ah) Time to ~80% charge (h)

20 3

60 8

100 12

225 25

20011010B

Termékspecifikációk

Márka:	Ctek
Kategória:	Akkumulátor töltő
Modell:	XS 7000

Szüksége van segítségre?

Ha segítségre van szüksége Ctek XS 7000, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek

Az Ön neve*

Az Ön e-mail címe*

Írja ide kérdését

Útmutatók Akkumulátor töltő Ctek

Ctek D250SE Útmutató

2 Szeptember 2024

Ctek READY AUTOMOTIVE Útmutató

31 Augusztus 2024

Ctek MXS 5.0 CHECK Acculader Útmutató

21 Augusztus 2024

Ctek MXS 5.0 POLAR Acculader Útmutató

21 Augusztus 2024

Ctek MXS 5.0 Test and Charge Acculader Útmutató

21 Augusztus 2024

Ctek PRO25SE Acculader Útmutató

20 Augusztus 2024

Ctek MXTS70 Acculader Útmutató

20 Augusztus 2024

Ctek MXT 14 Acculader Útmutató

20 Augusztus 2024

Ctek MXS 3.8 Acculader Útmutató

20 Augusztus 2024

Ctek Njord Go Acculader Útmutató

20 Augusztus 2024

Útmutatók Akkumulátor töltő

Legújabb útmutatók Akkumulátor töltő

Schwaiger LAD230 531 Útmutató

9 Április 2025

Schwaiger 658699 Útmutató

9 Április 2025

Schwaiger LAD440 532 Útmutató

9 Április 2025

Ergotron 97-939 Útmutató

3 Április 2025

Ergotron YES35 Útmutató

3 Április 2025

Trust Maxo 25242 Útmutató

3 Április 2025

Ergotron LiFeKinnex Útmutató

3 Április 2025

Voltcraft PB-19C Útmutató

31 Március 2025

Watson 9V-2BC Útmutató

30 Március 2025

ISDT Q6 Lite Útmutató

26 Március 2025