Használati útmutató Bunn ICB Infusion Series Twin Soft Heat

Bunn Kávéfőző ICB Infusion Series Twin Soft Heat

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Bunn ICB Infusion Series Twin Soft Heat (3 oldal) a Kávéfőző kategóriában. Ezt az útmutatót 7 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Oldal 1/3
BUNN-O-MATIC CORPORATION
POST OFFICE BOX 3227
SPRINGFIELD, ILLINOIS 62708-3227
PHONE: (217) 529-6601 FAX: (217) 529-6644
www.bunn.com
55227.0000A 07/18 ©2018 Bunn-O-Matic Corporation
ICB SH
ICB SH TWIN
Faucet Side Car Relocation
Instructions
TO BE PERFORMED BY QUALIFIED PERSONNEL
These instructions are intended for relocating the facuet side car on an ICB SH brewer. Ensure all tools are present before
performing the installation.
WARNING: Disconnect the brewer from the power source before performing the procedure. Ensure the
water is drained from the tank and be aware that many internal parts can be extremely hot; allow contents of
tank to cool before proceeding.
Note: If technical assistance is needed, please call 1-800-286-6345
Tools Required:
8/32 socket/wrench
Flat Blade Screwdriver
Remove the plastic badge from the right
side of the brewer.
Install the plastic badge on the left side of
the brewer to cover the panel holes.
Install the base screw that was removed
in step 5.
STEP 7
Remove the snap-in fastener from the
faucet side car and place into the hole
directly above as shown.
STEP 8
ICB SH Faucet Side Car Installation Instructions
Place the plate assembly into the
uncovered holes on the inside of the right
panel.
Place the spacer on the outside of the
right panel on the plate assembly.
STEP 9
Remove the base screw on the right side.
STEP 10
Align the faucet side car to the right side
of the brewer.
Secure the faucet side car using the
washers and screws that were removed in
step 5.
STEP 11
Insert the black grommet into the large
tubing hole. This is the same grommet
removed in step 5.
Secure the base screw to the faucet side
car.
STEP 12
Plastic Badge
Secure
Remove
Fastener
Insert
Fastener
Plate Assembly
Spacer
Remove Base Screw
Align
Secure with
Washers &
Screws
Grommet
Loosen the faucet nut to rotate the faucet
handle facing upwards.
Route the faucet tube through the right
side panel.’
Ensure there are no kinks in the tubing.
STEP 13
Attach the faucet tube to the faucet shank.
Secure the tube to the shank using the
hose snap that was removed in step 4.
STEP 14
ICB SH Faucet Side Car Installation Instructions
Secure the cover to the faucet side car
using the screws that were removed in
step 3.
STEP 15
Place the front panel on the brewer.
STEP 16
Secure the front panel to the brewer using
the screws removed in step 1.
STEP 17
Faucet side car relocation is complete.
STEP 18
Position Upright
Route Tube
Connect to
Shank
Secure with Clamp

Termékspecifikációk

Márka: Bunn
Kategória: Kávéfőző
Modell: ICB Infusion Series Twin Soft Heat

Szüksége van segítségre?

Ha segítségre van szüksége Bunn ICB Infusion Series Twin Soft Heat, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek




Útmutatók Kávéfőző Bunn

Bunn

Bunn 04275.0031 Útmutató

2 Szeptember 2024
Bunn

Bunn MCPA - My Cafe Útmutató

24 Augusztus 2024
Bunn

Bunn Single Útmutató

24 Augusztus 2024
Bunn

Bunn CWTF15-1 Útmutató

20 Augusztus 2024
Bunn

Bunn Axiom Twin Útmutató

20 Augusztus 2024
Bunn

Bunn CWTF35-3 Útmutató

20 Augusztus 2024

Útmutatók Kávéfőző

Legújabb útmutatók Kávéfőző